
Relay board
waterloo-rocketry/rlcsv3
Arduino code and electrical schematics for Waterloo Rocketry Remote Launch Control System V3

Arduino code and electrical schematics for Waterloo Rocketry Remote Launch Control System V3
Rlcs power is an open-source printed circuit board by waterloo-rocketry, from the waterloo-rocketry/rlcsv3 repository on GitHub, published under the MIT licence. It is a 2-layer board of 57.1 × 105.4 mm with 44 parts on 96 nets, routed with 232 tracks and 21 vias.
It is built around the LTD-4608JR. Its parts include 20 resistors, 8 connectors, 2 capacitors, 2 diodes and 2 transistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
RLCS stands for Remote Launch Control System. It's purpose is to fill our rocket with ethanol and nitrous oxide, then ignite the ignition puck inside the rocket, all from a distance of 3000' away at launch control. To do so, it has control over multiple valves at the rocket, a linear actuator to disconnect the fill arm from the rocket, and 2 ignition coils inside the ignition puck.
All Arduino firmware code is in /src
All electrical schematics and PCB layouts are in /schematics
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 150 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3, R4, R5, R6, R7, R8, R9, R10, R11 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R20, R24, R27, R28 |
| 2 | 20k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R19, R23 |
| 2 | 4.7K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R21, R22 |
| 2 | 5k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R12 |
| 2 | Conn_01x05_Male | Connector_JST:JST_EH_B5B-EH-A_1x05_P2.50mm_Vertical | J1, J2 |
| 2 | LOGO | rlcs_power_footprints:rocketry_logo_small_noletters | G***, G*** |
| 2 | Q_NPN_BEC | Package_TO_SOT_SMD:SOT-523 | Q1, Q2 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C3 |
| 1 | 12 to 5 | rlcs_power_footprints:VXO78XX-1000 | T2 |
| 1 | 12v Output | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J6 |
| 1 | 12v_test | Connector_PinSocket_2.00mm:PinSocket_1x01_P2.00mm_Vertical | TP1 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C4 |
| 1 | 5A | Fuse_Holders_and_Fuses:Fuseholder5x20_horiz_open_inline_Type-I | F1 |
| 1 | 5v Output | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J7 |
| 1 | 5v_test | Connector_PinSocket_2.00mm:PinSocket_1x01_P2.00mm_Vertical | TP4 |
| 1 | Actuator Battery Conn | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J5 |
| 1 | Arduino_Mega2560_Shield | rlcs_power_footprints:Arduino_Mega2560_Shield | XA1 |
| 1 | GND_test | Connector_PinSocket_2.00mm:PinSocket_1x01_P2.00mm_Vertical | TP3 |
| 1 | Green | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | Keylock Switch Conn | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-2_1x02_P2.54mm_Horizontal | J8 |
| 1 | LTD-4608JR | rlcs_power:LTD-4608JR | AFF1 |
| 1 | Power Board Power Input | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J4 |
| 1 | Red | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D2 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | S1 |
| 1 | UART Conn | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-2_1x02_P2.54mm_Horizontal | J3 |

waterloo-rocketry/rlcsv3
Arduino code and electrical schematics for Waterloo Rocketry Remote Launch Control System V3

waterloo-rocketry/rlcsv3
Arduino code and electrical schematics for Waterloo Rocketry Remote Launch Control System V3

waterloo-rocketry/rlcsv3
Arduino code and electrical schematics for Waterloo Rocketry Remote Launch Control System V3

waterloo-rocketry/rlcsv3
Arduino code and electrical schematics for Waterloo Rocketry Remote Launch Control System V3






mudmin/AnotherMaker
This is where I will store code snippets for AnotherMaker Videos

qbancoffee/imac_g3_ivad_board_init
iMac G3 IVAD board initialization with an arduino

Stefan-Olt/MISRC
MISRC Is a multi channel RF capture device for FM RF, S-Video, CVBS RAW capture and anything else, but intended and supported for the decode family of projects vhs-decode, ld-decode, hifi-decode.
It measures 57.1 × 105.4 mm and has 2 copper layers, 1.6 mm thick.
44 parts, built around the LTD-4608JR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the waterloo-rocketry/rlcsv3 repository on GitHub, at the commit this page was made from: the board is schematics/power_board_schematics/rlcs_power.kicad_pcb and its schematic schematics/can_support_schematics/Hardwired CAN support.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).