

Telephonica
RPico based device for GSM call proxy
- Size
- 95 × 70 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 27
- Nets
- 40
- Pads
- 142
- Tracks, vias
- 61, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 2 Apr 2023
- Updated
- 16 Sep 2024
Overview
Telephonica is an open-source printed circuit board by vladbalmos, from the vladbalmos/telephonicah repository on GitHub, published under the MIT licence. It is a 2-layer board of 95 × 70 mm with 27 parts on 40 nets, routed with 61 tracks and 0 vias.
Its parts include 6 capacitors, 3 resistors, 2 diodes, 2 connectors and 1 IC. It belongs with the RP2040 boards of this library.
README
README.mdUPDATE
The original version of this project is on branch original-call-proxy. The master branch doesn't forward calls to a designated number, instead it activates an external connected remote control using the signal port (see the schematic in the hw folder for the signal port pinout).
Telephonicah
This repo contains firmware and hardware related resources (schematic, pcb & enclosure 3d models) for a device used to proxy GSM calls to a designated number (ex: parking barrier gate).
Hardware requirements:
* Raspberry Pi Pico W
* SIM800 GSM Module
* 5V@2.5A power supply
* capacitors: 100nf, 4.7uf, 2200uf
* resistors: 2x150ohm, 1Mohm
* leds: red, greenThe Pico controls the SIM800 module via UART.
Features:
* SMS based commands:
* get remaining credit
* delete SIM stored SMSs
* connect to wifi
* query wifi status
* Relay received SMS to designated owner number
* Web UIAfter the devices connects to WIFI it will bind the webserver to port 8080 and a SMS containing the server's ip address and port will be sent to the administrator's phone number
System requirements
- micropython
- ampy (pip3 install adafruit-ampy)
- minicom (optional)
Development
Linux
Build micropython:
cd [mycropython-dir]
make -C mpy-cross
cd [mycropython-dir]/ports/rp2
make -j4 BOARD=PICO_W submodules
make -j4 BOARD=PICO_W clean
make -j4 BOARD=PICO_WAfter building copy the micropython firmware to a pico
Init: ./setup.sh # edit src/phone_numbers.py and add phone numbers make build
Run:
make runClean
make cleanBuild
make buildWindows
Build micropython https://github.com/micropython/micropython/tree/master/ports/windows
After building copy the micropython firmware to a pico
Edit build.ps1 and change the $PORT variable to the correct serial port (ex: com1)
Init:
.\setup.ps1
# edit src/phone_numbers.py and add phone numbers
.\build.ps1 -Command buildRun:
.\build.ps1 -Command runClean:
.\build.ps1 -Command cleanBuild:
.\build.ps1 -Command buildList files on pico:
.\build.ps1 -Command listCopy file from pico:
.\build.ps1 -Command get -Argument [filename]Copy file to pico:
.\build.ps1 -Command send -Argument [filename]Parts
27| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | , , , , , | ||
| 2 | 100nf | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C1, C5 |
| 2 | 150 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2 |
| 2 | 4.7uf | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C2, C4 |
| 2 | LED | LED_THT:LED_D5.0mm | D1, D2 |
| 1 | 1M | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
| 1 | 2200uf | Capacitor_THT:C_Radial_D12.5mm_H20.0mm_P5.00mm | C3 |
| 1 | 47uf | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C6 |
| 1 | AudioJack3 | Connector_Audio:Jack_3.5mm_CUI_SJ1-3525N_Horizontal | J1 |
| 1 | Conn_01x07_Female | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J2 |
| 1 | Pico | MCU_RaspberryPi_and_Boards:RPi_Pico_SMD_TH | U1 |
The 20 most common of 27 parts.
Similar boards
- 2 layers47.6 × 27.3 mm

- 2 layers77.4 × 77.4 mm

CORAZON LEDS CON FADE
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
27 parts915 - 2 layers44.2 × 29.3 mm

- 2 layers40 × 40 mm

- 2 layers22 × 42 mm

Nvme bm to e
CRImier/MyKiCad
My KiCad boards. Can't be bothered uploading individually anymore, so here you go.
27 parts253GPL-3.0 - 2 layers80 × 61 mm

PicoProducer
pjgpetecodes/pico-streamdeck
This project is an OBS Controller using a Raspberry Pi Pico and CircuitPython.
27 parts230MIT - 2 layers186 × 45 mm

AddOnD
freeDSP/freeDSP-aurora
freeDSP ADAU1452 with 8 analog input, 8 analog outputs, S/P-DIF I/O, ADAT I/O, USB Audio Class2, WiFi, Bluetooth
27 parts226CC-BY-SA-4.0 - 2 layers29.6 × 40.6 mm

Dbwifi revB
ugcs/ddc
Drone Show Software is software designed for drone shows, allowing flight path planning as well as control of dozens of drones simultaneously in a synchronized manner.
27 parts223
Questions
How big is the Telephonica PCB?
It measures 95 × 70 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Telephonica use?
27 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Telephonica KiCad files?
From the vladbalmos/telephonicah repository on GitHub, at the commit this page was made from: the board is hw/board/telephonica/telephonica.kicad_pcb and its schematic hw/board/telephonica/telephonica.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Telephonica design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).