

KiCad Editable Circuit for Tricoder-Rev2
- Size
- 59.2 × 21.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 54
- Nets
- 9
- Pads
- 80
- Tracks, vias
- 170, 40
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 3 May 2026
- Updated
- 8 Jul 2026
Overview
Tricoder is an open-source printed circuit board by vishalqsoni, from the vishalqsoni/Tricoder-Rev2-Circuits repository on GitHub. It is a 2-layer board of 59.2 × 21.4 mm with 54 parts on 9 nets, routed with 170 tracks and 40 vias.
It is built around the WS2812B-2020.
Main components
1README
README.mdStar Trek Tricorder Rev2 — PCB & Schematics
KiCad schematic and PCB layout files for the Star Trek Tricorder Rev2. The hardware is distributed across three boards — Tricorder Main, Tricorder Sensor, and Tricorder LED Array 2 — interconnected via a 20-pin FFC cable.
Table of Contents
- Board Overview
- Tricorder Main
- Tricorder Sensor
- Tricorder LED Array 2
- Interconnect
- Repository Structure
- Tools Used
- Related Repositories
- Credits
Board Overview
The hardware is split across three dedicated PCBs to keep the design modular and assembly manageable within the compact Tricorder enclosure.
| Board | Role | Files Available |
|---|---|---|
| Tricorder Main | Central controller — ESP32S3, display, audio, touch input | Schematic + Layout |
| Tricorder Sensor | Environmental sensing, power monitoring, LED array 1 | Layout only |
| Tricorder LED Array 2 | Secondary WS2812B LED array | Schematic + Layout |
All boards are KiCad projects and communicate over a shared I²C bus via a 20-pin 1mm pitch FFC cable.
Tricorder Main
The Main PCB is the central control unit built around the Seeed Studio XIAO ESP32S3. It sits directly below the TFT display and coordinates all subsystems.
Files: Schematic + Layout
Interfaces
| Interface | Protocol | Connected To |
|---|---|---|
| TFT Display (ST7735) | SPI (MOSI, SCK, CS, DC, RST) | ST7735 1.8" TFT |
| Audio Module (JQ6500) | UART (TX/RX) | JQ6500 |
| GPIO Expander (MCP23008) | I²C (SDA/SCL) | TTP223 touch inputs ×6 |
| LED Array — Primary | Single-wire (WS2812B protocol) | WS2812B LEDs |
| FFC Connector | 20-pin, 1mm pitch | Tricorder Sensor board |
Key ICs
| IC / Module | Function |
|---|---|
| Seeed Studio XIAO ESP32S3 | Main microcontroller |
| MCP23008 | I²C GPIO expander for touch input routing |
| JQ6500 | UART audio playback module |
| TTP223 ×6 | Capacitive touch sensors |
| WS2812B (2020) | Addressable RGB LEDs — primary array |
Tricorder Sensor
The Sensor Panel contains all environmental sensing and power monitoring components, along with LED Array 1. It connects to the Main PCB entirely over the FFC cable.
Files: Layout only
Interfaces
| Interface | Protocol | Connected To |
|---|---|---|
| Environmental Sensor (BME280) | I²C | Shared I²C bus |
| Power Monitor (INA219) | I²C | Shared I²C bus |
| LED Array 1 | Single-wire (WS2812B protocol) | WS2812B LEDs |
| FFC Connector | 20-pin, 1mm pitch | Tricorder Main board |
Key ICs
| IC / Module | Function |
|---|---|
| DFRobot BME280 | Temperature, pressure, and altitude sensing |
| INA219 | Voltage, current, and power monitoring |
| WS2812B (2020) | Addressable RGB LEDs — array 1 |
Tricorder LED Array 2
A dedicated board for the secondary WS2812B LED array.
Files: Schematic + Layout
Specifications
| Parameter | Value |
|---|---|
| PCB Material | FR4 |
| Board Thickness | 0.6 mm |
Key IC
| IC / Module | Function |
|---|---|
| WS2812B (2020) | Addressable RGB LEDs — array 2 |
Interconnect — FFC Cable
All boards communicate over a 20-pin, 1mm pitch FFC cable, which carries:
| Signal Group | Lines |
|---|---|
| Power | VCC, GND |
| I²C Bus | SDA, SCL |
| LED Control | WS2812B data line |
| Miscellaneous | Additional control and status signals |
Using FFC keeps internal wiring clean, reduces assembly complexity, and allows each board to be removed or replaced independently.
Repository Structure
tricorder-rev2-circuits/
│
├── tricorder-main/
│ ├── tricorder-main.kicad_pro
│ ├── tricorder-main.kicad_sch
│ ├── tricorder-main.kicad_pcb
│ └── gerbers/
│
├── tricorder-sensor/
│ ├── tricorder-sensor.kicad_pro
│ ├── tricorder-sensor.kicad_pcb
│ └── gerbers/
│
├── tricorder-led-array-2/
│ ├── tricorder-led-array-2.kicad_pro
│ ├── tricorder-led-array-2.kicad_sch
│ ├── tricorder-led-array-2.kicad_pcb
│ └── gerbers/
│
└── docs/
└── block-diagram.pngTools Used
| Tool | Purpose |
|---|---|
| KiCad | Schematic capture and PCB layout |
Related Repositories
| Repository | Contents |
|---|---|
| Tricorder Rev2 — Firmware | Arduino firmware, UI, sensors, animations |
| Tricorder Rev2 — 3D Models [blocked] | Enclosure and mechanical files |
Credits
- PCB Design & Hardware — Vishal Soni
- 3D Printing — JustWay
- Firmware- Vishal Soni
License
MIT License — see LICENSE for details.
Parts
54| Qty | Value | Footprint | References |
|---|---|---|---|
| 28 | , , , , , , , , , , , , , , , +12 | ||
| 13 | WS2812B-2020 | LED_SMD:LED_WS2812B-2020_PLCC4_2.0x2.0mm | D1, D1, D1, D1, D1, D1, D2, D3, D4, D5, D6, D7, D8 |
| 2 | G*** | kibuzzard-69B452F6 | kibuzzard-69B452F6, kibuzzard-69B452F6 |
| 1 | G*** | kibuzzard-69B4043D | kibuzzard-69B4043D |
| 1 | G*** | kibuzzard-69B59139 | kibuzzard-69B59139 |
| 1 | G*** | kibuzzard-69B3FDA1 | kibuzzard-69B3FDA1 |
| 1 | G*** | kibuzzard-69B4041F | kibuzzard-69B4041F |
| 1 | G*** | kibuzzard-69B4529B | kibuzzard-69B4529B |
| 1 | G*** | kibuzzard-69B45234 | kibuzzard-69B45234 |
| 1 | G*** | kibuzzard-69B455A9 | kibuzzard-69B455A9 |
| 1 | G*** | kibuzzard-69B452CC | kibuzzard-69B452CC |
| 1 | G*** | kibuzzard-69B5913D | kibuzzard-69B5913D |
| 1 | G*** | kibuzzard-69B59132 | kibuzzard-69B59132 |
| 1 | G*** | kibuzzard-69B3FD8B | kibuzzard-69B3FD8B |
More from vishalqsoni/Tricoder-Rev2-Circuits
2- 2 layers60.3 × 60.4 mm

- 2 layers65 × 30 mm

Similar boards
- 4 layers16.9 × 119.4 mm

- 4 layers78 × 59 mm

- 2 layers240 × 240 mm

- 2 layers26 × 28 mm

- 2 layers86 × 54 mm

- 4 layers35 × 85 mm

Vimdrones esc development board
VimDrones/AM32_esc_development_board
Open Source AM32 ESC development board
95 parts44GPL-3.0 - 2 layers31.9 × 36 mm

Lemon pcb swizzle
rianadon/Cosmos-Keyboard-PCBs
Open-Source keyboard PCB designs for the Cosmos Keyboard Generator
63 parts43 - 6 layers155.5 × 194.6 mm

NerdEKO Gamma NoATX
phil31/NerdEKO-Gamma
fork of the NerdOCTAXE-Gamma design (https://github.com/Patsch91/NerdOCTAXE-Gamma), with 12 x BM1370 (14TH/s SHA256)
499 parts42
Questions
How big is the Tricoder PCB?
It measures 59.2 × 21.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Tricoder use?
54 parts, built around the WS2812B-2020. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Tricoder KiCad files?
From the vishalqsoni/Tricoder-Rev2-Circuits repository on GitHub, at the commit this page was made from: the board is Tricoder/Tricoder.kicad_pcb and its schematic Tricoder main/Tricoder main.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Tricoder design in my own project?
Its repository states no licence, so its author keeps all rights: ask vishalqsoni before reusing the design.