

Walter remix - C3v2
- Size
- 33 × 50 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 56
- Nets
- 97
- Pads
- 384
- Tracks, vias
- 511, 78
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 3 Jan 2025
- Updated
- 27 Jan 2025
Overview
Walter remix - C3v2 is an open-source printed circuit board by vichalder, from the vichalder/PCB-design repository on GitHub. It is a 4-layer board of 33 × 50 mm with 56 parts on 97 nets, routed with 511 tracks and 78 vias.
It is built around the BGU8019X, ESP32-C3-WROOM-02-H4 and LM2575-3.3BU, with the DMP2021UFDE, TPS7A0518PYKAR and CONUFL001-SMD-T among its other parts. Its parts include 25 resistors, 12 capacitors, 5 ICs, 5 connectors and 2 switches. It belongs with the ESP32 and RISC-V boards of this library.
Main components
9BGU8019X
XSON-6(0.7x1.1)-40℃~+85℃ -7dBm 0.55dB 1.559GHz~1.61GHz 1.5V~3.1V 12dB 13dB 18.5dB 4.6mA 6dBm Low power mode、Bias control circuit、Electrostatic protection XSON-6(0.7x1.1) RF Amplifiers ROHSNXP SemiconductorsRF AmplifiersESP32-C3-WROOM-02-H4
SMD,20x18mm-105dBm -40℃~+105℃ 2.4GHz 20.5dBm 345mA 3V~3.6V 82mA Bluetooth5.0 ESP32-C3 On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,20x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesLM2575-3.3BU
TO-263-5-40℃~+125℃@(TJ) 1 1A 3.3V 4V~40V 52kHz 5mA Buck Built-in Fixed No Overcurrent Protection、Cycle-by-cycle current limiting Step-down type TO-263-5 DC-DC ConvertersMicrochip TechnologyDC-DC ConvertersDMP2021UFDE
UDFN2020-6-55℃~+150℃ 1 P-Channel 1.9W 1V 2.76nF 20V 220pF 22mΩ@2.5V 262pF 59nC@8V 9A P-Channel UDFN2020-6 MOSFETs ROHSDiodes IncorporatedMOSFETsTPS7A0518PYKAR
DSBGA-4-40℃~+125℃@(Tj) 1 1.8V 180uVrms 1uA 200mA 341mV@(200mA) 40dB@(1kHz) 5.5V Fixed Over Current Protection、Over Temperature Protection、Enable、Thermal Shutdown Positive DSBGA-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsCONUFL001-SMD-T
SMD-40℃~+90℃ 1 50Ω 6GHz Board Side Male Pin SMD Coaxial Connectors (RF) ROHSTE ConnectivityCoaxial Connectors (RF)B39162B8813P810
-- SAW Filters ROHSTDKSAW FiltersLQW03AW10NJ00D
SMD,0.4x0.5mm10nH 250mA 37@900MHz 460mΩ 7.2GHz ±5% SMD,0.4x0.5mm Inductors (SMD) ROHSMurataInductors (SMD)NX3008PBK,215-JSM
SOT-23-55℃~+150℃ 1 P-Channel 1.6V 1.7nC 1.8pF 170mA 225mW 30V 3pF 4.4Ω@4.5V 43pF P-Channel Standalone ±20V SOT-23 MOSFETs ROHSJSMSEMIMOSFETs
Parts
56| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100k | Resistor_SMD:R_0201_0603Metric | R1, R2, R3, R4, R5, R6, R7, R9, R10, R20, R21 |
| 4 | 100uF | Capacitor_SMD:C_0201_0603Metric | C5, C6, C7, C8 |
| 4 | DNP | Resistor_SMD:R_0201_0603Metric | R11, R13, R15, R16 |
| 3 | 10k | Resistor_SMD:R_0201_0603Metric | R22, R23, R25 |
| 3 | 10uF | Capacitor_SMD:C_0201_0603Metric | C2, C3, C10 |
| 2 | 0 | Resistor_SMD:R_0201_0603Metric | R14, R24 |
| 2 | 0R0 | Resistor_SMD:R_0201_0603Metric | R12, R17 |
| 2 | 100nF | Capacitor_SMD:C_0201_0603Metric | C1, C11 |
| 2 | 1uF | Capacitor_SMD:C_0201_0603Metric | C4, C12 |
| 2 | 5.1k | Resistor_SMD:R_0201_0603Metric | R18, R19 |
| 2 | CONUFL001-SMD-T | RF_Antenna:CONUFL001-SMD-T | J4, J5 |
| 1 | 0.47uH | Inductor_SMD:Inductor 0.47uH | L1 |
| 1 | 1548130 | 158130:1548130 | J6 |
| 1 | 1N5819 | 1N5819HW-7-F:SOD3715X145N | D1 |
| 1 | 4.7k | Resistor_SMD:R_0201_0603Metric | R8 |
| 1 | B39162B8813P810 | Filter:Filter_1109-5_1.1x0.9mm | FL1 |
| 1 | BGU8019 | RF:BGU8019 | U5 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_CUI_CPT-9019S-SMT | BZ1 |
| 1 | DMP2021UFDE | Package_DirectFET:DMP2021UFDE | U2 |
| 1 | DNP | Capacitor_SMD:C_0201_0603Metric | C9 |
| 1 | ESP32-C3-WROOM-02 | PCM_Espressif:ESP32-C3-WROOM-02 | U3 |
| 1 | LM2575-3.3BU | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U4 |
| 1 | LQW03AW10NJ00D | Inductor_SMD:LQW03AW10NJ00D | L2 |
| 1 | NX3008PBK,215 | NX3008PBK,215:NX3008PBK215 | Q1 |
| 1 | SIM8055-6-1-14-00-1 | RF:SIM8055-6-1-14-01-A | J2 |
| 1 | SW_RST | Switch_fra_tutorial:PTS815SJK250SMTRLFS | SW2 |
| 1 | TPS7A0518PYKAR | Module:BGA4C35P2X2_66X66X40 | IC1 |
| 1 | Tilt switch | Button_Switch_SMD:Tilt switch | SW1 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | ~ | RF_Module:Sequans Monarch 2 GM02SP | GM02SP1 |
More from vichalder/PCB-design
2- 4 layers26.1 × 43 mm

- 4 layers23.5 × 51 mm

Similar boards
- 4 layers66.8 × 44 mm

- 2 layers30.5 × 21.5 mm

- 4 layers75 × 100 mm

Test rig black box
callumsnowden/aero21412_test_rig
AERO21412 Avionics Coursework 1 – Wind Tunnel Test Rig "Black Box"
102 parts1MIT - 6 layers52 × 34 mm

WINTER
SparrowTheNerd/WINTER-KiCAD
KiCAD Files for all WINTER (Wireless Inertial iNformation and Telemetry for Energetics Regulation) flight computer
109 partsGPL-3.0 - 4 layers40 × 66.6 mm

CanSat
SzymonLy/Quadcopter_2.1
Projekt PCB do autonomicznego quadcoptera, wersja finalna i sprawna
142 parts - 4 layers51.3 × 23.4 mm

- 4 layers100 × 66.2 mm

Top PCB
StanZalewski/Autonomous-remote-monitoring-system-based-on-the-LoRaWAN-protocol
Solar-powered LoRaWAN weather station — 3 custom PCBs, bare-metal STM32, 4.3 km verified link
57 parts - 4 layers162.6 × 48.3 mm

Pcb esp32 wled pwm multichannel
btittelbach/esp32_12chan_lowside_pwm_pcb
Open Hardware PCB designed to drive 12 low-side PWM channels.
100 parts3
Questions
How big is the Walter remix - C3v2 PCB?
It measures 33 × 50 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Walter remix - C3v2 use?
56 parts, built around the BGU8019X, ESP32-C3-WROOM-02-H4, LM2575-3.3BU and DMP2021UFDE. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Walter remix - C3v2 KiCad files?
From the vichalder/PCB-design repository on GitHub, at the commit this page was made from: the board is walter_remix - C3 - V2/walter_remix - C3v2.kicad_pcb and its schematic walter_remix - C3 - V2/walter_remix - C3v2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Walter remix - C3v2 design in my own project?
Its repository states no licence, so its author keeps all rights: ask vichalder before reusing the design.