Skip to the content
2 layers70 × 34 mmConnector breakout, the printed circuit board in 3D

A hyper-specific collection of mods for converting Pump It Up arcade pads to expensive USB controllers.

Size
70 × 34 mm
Copper layers
2
Thickness
1.6 mm
Parts
9
Nets
5
Pads
22
Tracks, vias
58, 1
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
25 Apr 2024
Updated
5 Nov 2024

Overview

Connector breakout is an open-source printed circuit board by veroxzik, from the veroxzik/pump-ac-conversion repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 70 × 34 mm with 9 parts on 5 nets, routed with 58 tracks and 1 via.

It belongs with the retro computing and games and interfaces and adapters boards of this library.

README

README.md

Pump AC Conversion

This repo contains files for my hyper-specific desire to get rid of all the rusted metal and busted sensors from my Pump It Up arcade pads.

It features the odd choice to keep bracketed panels, due to cost. In the future, I may modify the files to also support bracketless panels.

Code

The code is designed around RP2040. Install the arduino-pico core and compiled using the Arduino IDE.

At the top of the code lists panelPins, an array grouping 4 pins for each of the 5 panels. You can change these if you are not using the boards as I've designed.

c
int panelPins[5][4] =
  {
    {0, 1, 2, 3},
    {4, 5, 6, 7},
    {8, 9, 10, 11},
    {12, 13, 14, 15},
    {16, 17, 18, 19}
  };

This code is simplistic. There's no debounce. If any switch is triggered, it will trigger the entire panel.

CAD

New frames were designed to be 3D printed (as all of mine were rusted). They are designed to use the existing bracketed panels and replaces the sensors with cheap generic dance sensors.

The frames are modular, consisting of corner supports and a choice of two side segments to form either the square or rectangle frames. A small printed top goes on the sensor to distribute the load and provide a place to tape mod.

A partial assembly is shown below:

Boards

Two boards are contained in this repo.

Pad Board

The pad board takes a Raspberry Pi Pico as the main microcontroller, and has several JST XH connectors to mate with the connector boards, discussed below. There's also another JST XH connector for a WS2812B output, and for USB input.

Connector Boards

The connector boards are designed to screw into the area where the L-Bracket is mounted. Two are required for each panel. Each daughter board has (2) JST XH 2P connectors for the generic dance sensor, (2) JST XH 3P connectors for linking two connector boards together (OUT on one board goes to IN on the other), and (2) JST XH 5P connectors to bring signals back to the pad board (only one is necessary to use, but both are included for easier wire routing.

Parts

9
QtyValueFootprintReferences
2M4 HoleMountingHole:MountingHole_4.3mm_M4H1, H2
2XH-2Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_VerticalJ1, J2
2XH-3Connector_JST:JST_XH_S3B-XH-A-1_1x03_P2.50mm_HorizontalJ3, J4
2XH-5Connector_JST:JST_XH_S5B-XH-A-1_1x05_P2.50mm_HorizontalJ5, J6
1LOGOVXZK:vxzk_logoG***

More from veroxzik/pump-ac-conversion

1
  • 2 layers55 × 89.5 mmPad board, the printed circuit board in 3D

    Pad board

    veroxzik/pump-ac-conversion

    A hyper-specific collection of mods for converting Pump It Up arcade pads to expensive USB controllers.

    16 parts2GPL-3.0

Similar boards

  • 2 layers103 × 30.5 mmTS Back Endcap, the printed circuit board in 3D

    TS Back Endcap

    EEVengers/ThunderScope

    ThunderScope GitHub Repo

    9 parts1.3kMIT
  • 2 layers31.8 × 47.6 mmNGC 38 connector, the printed circuit board in 3D

    NGC 38 connector

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    9 parts1.2k
  • 2 layers24 × 27.3 mmExpansion Card Retrofit, the printed circuit board in 3D

    Expansion Card Retrofit

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    9 parts1.1kCC-BY-4.0
  • 2 layers15.6 × 17.3 mmSKR Mini TFT Thermistor Board, the printed circuit board in 3D

    SKR Mini TFT Thermistor Board

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    9 parts1.1kGPL-3.0
  • 2 layers39.1 × 49.5 mmLearnoliver, the printed circuit board in 3D

    Learnoliver

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    9 parts915
  • 2 layers17.4 × 16.9 mmToolhead, the printed circuit board in 3D

    Toolhead

    tanaes/whopping_Voron_mods

    9 parts787GPL-3.0
  • 2 layers9.8 × 108 mmExpander, the printed circuit board in 3D

    Expander

    wntrblm/Castor_and_Pollux

    A Juno-inspired dual oscillator

    9 parts587
  • 2 layersKeyboard after, the printed circuit board in 3D

    Keyboard after

    adamws/kicad-kbplacer

    KiCad plugin for automatic keyboard's key placement and routing

    9 parts547GPL-3.0

Questions

How big is the Connector breakout PCB?

It measures 70 × 34 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Connector breakout use?

9 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Connector breakout KiCad files?

From the veroxzik/pump-ac-conversion repository on GitHub, at the commit this page was made from: the board is boards/connector-breakout/connector-breakout.kicad_pcb and its schematic boards/connector-breakout/connector-breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Connector breakout design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).