
SNAC2IEC Breakout
venice1200/MiSTer_SNAC2IEC
Commodore/CBM IEC Adapter for MiSTer FPGA

Commodore/CBM IEC Adapter for MiSTer FPGA
SNAC2IEC Breakout is an open-source printed circuit board by venice1200, from the venice1200/MiSTer_SNAC2IEC repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 50 × 36 mm with 28 parts on 16 nets, routed with 73 tracks and 50 vias.
It is built around the AZ1117CH-3.3TRG1 and BSS138. Its parts include 12 resistors, 4 transistors, 3 capacitors, 3 connectors and 1 IC. It belongs with the interfaces and adapters and fPGA and programmable logic boards of this library.
Inspired from the SNAC Accessory Converter and the IEC Support of the C64 Core
I created together with dtimber this little Adapter PCB for the MiSTer FPGA.
The Adapter converts the MiSTer FPGA User Port (Serial IO) into a Commodore IEC/CBM (Serial) Bus Port.
Use the Adapter to connect a real Commodore Floppy 1541 or compatible devices (SD2IEC/PI1541) to your MiSTer.
I know there are better and faster ways to load a game into a MiSTer's Core, but this is fun 🚀.
C64, C128, Commodore Plus/4
SD2IEC, PI1541, CBM 1541, CBM1541-II, CBM1571, CBM1581 and Printer MPS-803.
Cores and some Hardware Devices are also tested with JiffyDOS 🚀.
Double check the User Video below.
I used "breakout Parts" for the used Voltage-Levelshifter and the Voltage-Regulator as I had them in stock.
There is also a Full-SMD-Version available, created by dtimber who created the Case as well.
The first Picture shows the "Breakout Version", the second the "Full-SMD Version".

Changes:
The first Picture shows the "Breakout Version", the second the "Full-SMD Version".

The Case was designed to look like the C64 Power Supply

Connector View

Left Connector = IEC/CBM Bus, right Connector = 5V Power from SNAC Port
Soldered PCB Version with Level Shifter.
Use it with the Standard IO Board with SNAC Port and 3.3V Signal Level.

You need all parts except the "optional's".
Soldered PCB Version without Level Shifter.
Only usable with the "first" PCB Versions.
Use it with SNAC Port's with integrated Level Shifter or with blue212's external SNAC Adapter and 5V Signal Level.

Just add some 0R 0805 Resistors or a blob of solder to R1,R2,R3 and R4.
A look inside...

All Parts for the Breakout-Version

| Part | Type |
|---|---|
| R1-R4 | 0 ohm 0805 resistors (optional, see schematics) |
| C1 | 4,7uF 0805 capacitor (optional, see schematics) |
| J1 | USB3 type A connector |
| J2 | 6 pin DIN connector (MAS60) |
| J3 | DC barrel connector (optional, 5.5/2.1 mm should be fine for most PSUs) |
| U1 | 4-Channel Voltage-Levelshifter (5V/3.3V), add a second stacked Levelshifter for SRQ |
| U2 | 5V to 3.3V Voltage Regulator |
| Part | Type |
|---|---|
| R1-R4 | 0 ohm 0805 resistors (optional, see schematics) |
| R5-R12 | 10k 0805 resistors |
| C1-C3 | 22nf 0805 capacitors |
| Q1-Q4 | N-Channel SOT23 MOSFET transistors (BSS138 or similar) |
| U1 | 3.3v LM1117 SOT223 regulator |
| J1 | USB3 type A connector |
| J2 | 6 pin DIN connector (MAS60) |
| J3 | DC barrel connector (optional, 5.5/2.1 mm should be fine for most PSUs) |
| Part | Type |
|---|---|
| R1-R10 | 10k 0805 resistors |
| C1-C3 | 22nf 0805 capacitors |
| Q1-Q5 | N-Channel SOT23 MOSFET transistors (BSS138 or similar) |
| U1 | 3.3v LM1117 SOT223 regulator |
| J1 | USB3 type A connector |
| J2 | 6 pin DIN connector (MAS60) |
| J3 | DC barrel connector (optional, 5.5/2.1 mm should be fine for most PSUs) |
| Part | Type |
|---|---|
| Brass Nuts | M3, outer size 4,6mm, lenght 6mm |
| Screws | M3, Counter Sunk, length 17mm |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 10K | Resistor_SMD:R_0805_2012Metric | R5, R6, R7, R8, R9, R10, R11, R12 |
| 4 | 0R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4 |
| 4 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4 |
| 4 | M3 | MountingHole:MountingHole_3.2mm_M3_ISO7380_Pad | H1, H2, H3, H4 |
| 3 | 22uF | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3 |
| 1 | Symbol:KiCad-Logo2_5mm_Copper | ||
| 1 | AZ1117CH-3.3TRG1 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | Barrel_Jack | Connector_BarrelJack:BarrelJack_Wuerth_6941xx301002 | J3 |
| 1 | DIN-6 | VeniceFootprints:DIN_6Pin_Print_Connector_IEC_Layout | J2 |
| 1 | USB3_A | Connector_USB:USB3_A_Plug_Wuerth_692112030100_Horizontal | J1 |

venice1200/MiSTer_SNAC2IEC
Commodore/CBM IEC Adapter for MiSTer FPGA

venice1200/MiSTer_SNAC2IEC
Commodore/CBM IEC Adapter for MiSTer FPGA



proveskit/flight_controller_board
The main flight computer board for the PROVES Kit.



garrettsworkshop/WarpSE
WIP 25 MHz MC68HC000-based accelerator card for Macintosh SE

johnwinans/2057-ICE40HX4K-TQ144-breakout
Minimal Raspberry PI breakout board for ICE40HX4K FPGA

martinroger/ipodesp32
An iPod emulator for 2006-2013 BMW Mini Coopers that need Bluetooth
It measures 50 × 36 mm and has 2 copper layers, 1.6 mm thick.
28 parts, built around the AZ1117CH-3.3TRG1 and BSS138. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the venice1200/MiSTer_SNAC2IEC repository on GitHub, at the commit this page was made from: the board is KiCad/SD2IEC_SMD_Version/SNAC2IEC_Breakout.kicad_pcb and its schematic KiCad/SD2IEC_Breakout_Version/SNAC2IEC_Breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).