Skip to the content
2 layers54.9 × 34.3 mmCutMachine PCB, the printed circuit board in 3D

The Resistor and LED Cutting machine is a community project to make mass-production of small SMD components cut to specific unit sizes faster and easier to make for our highly popular MiniBadge initiatives and…

Size
54.9 × 34.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
10
Nets
8
Pads
34
Tracks, vias
43, 0
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
9 Jun 2024
Updated
12 Sep 2024

Overview

CutMachine PCB is an open-source printed circuit board by utahsaint-org, from the utahsaint-org/CutMachineSMD repository on GitHub. It is a 2-layer board of 54.9 × 34.3 mm with 10 parts on 8 nets, routed with 43 tracks and 0 vias.

Its parts include 4 resistors, 1 connector and 1 switch.

README

README.md

CutMachineSMD

The Resistor and LED Cutting machine is a community project to make mass-production of small SMD components cut to specific unit sizes faster and easier to make for our highly popular MiniBadge initiatives and standards. This machine has been used in mass-production and works great for feeding and cutting several component types.

Key Features
  • SMD Tape Cutting
  • Custom Menu-Driven Calibration Settings
  • Test Cutting and Program Cutting
  • Sharpie Attachment to allow color-coding of components as they are cut
  • Community Contribution

Parts List:

For convenience I have an Amazon List for most parts: https://a.co/ecXTVj9

  • 2020 Extruded Aluminium cut to
    • 2x 30cm - Top/Bottom
    • 3x 26cm - Verticals
    • 2x 20cm - Legs
    • 1x 155mm - Horizontal Crossmember
    • 1x 155mm - Roll Attachment Crossmember (Optional)
  • 2020 Series Connectors and Corner Bracket Set (30 Piece)
  • Bracket L-Type Internal Connectors for 2020 Series
  • 4x 2020 Series Rubber Feet
  • Stepper Motors
    • NEMA23 4.2Amp Motor (StepperOnline 23HS45-4204S)
    • NEMA17 1.2Amp Motor (StepperOnline 17HS19-2004S)
  • Motor Drivers
    • 1x EASON Stepper Motor Driver TB6600 4A
    • 2x Stepper Motor Driver DRV8825
  • Cutting Blades - 9mm Knife Replacement Blade Cartridge
  • Electronics
    • Arduino Uno R3 or similar device.
    • HiLetgo CNC Drive Expansion Board (CNC Shield)
    • 2.42" 128x64 OLED LCD Display (SSD1309) i2C
  • M3 Hardware
    • Assorted M2 Length Screws, Nuts, Washers
    • Assorted M3 Length Screws, Nuts, Washers
    • Assorted M5 Length Screws, Nuts, Washers
    • M3 Lever Steering Linkage
    • M3 Link Strut shaft 35mm
  • 1x Miniature Linear Sliding Guideway Rail 150mm
  • Power Supplies
    • 12VDC 15A Linear Power Supply
    • 12VDC to 5VDC Stepdown Regulator to power the Arduino (Optional)
  • Components for PCBs (Digikey/Mouser or Similar)
    • 4x 6mm THT PushButton Switchs
    • 6x 10KΩ SMD 1206 Resistors
    • 1x 220Ω SMD 1206 Resistor
    • 1x 2.2KΩ SMD 1206 Resistor
    • 7+ Position Right-Angle PIN Headers
    • 3+ Position Straight PIN Headers
  • PCBs Ordered (JLC_PCB or Similar)

Setup and Configuration

OLED Screen Modification

The OLED screen typically comes configured for SPI interface, and we are using I2C protocol in this project. As such, you will need to modify the OLED screen by bridging several solder pads to put the screen into I2C configuration. You will need to disconnect the ribbon-cable and underneath you will need to bridge the solder pads labeled: R9, R10, R11, R12. You will also need to remove the Resistor labeled R8. (Follow the published instructions for the screen to make this modification)

Building the Framework

The Framework for the machine is fairly stratight-forward. The 30cm struts are mounted as the top and bottom rails. Use normal corner attachments to make the connections. The 26cm vertical struts are attached with one in the middle and the other two are attached on the edges to make a 30cm x 30cm frame. The center vertical is attached at 105mm spacing from center to center or 85mm Internal spacing. You can use the Acrylic Cut Head mount as the spacing guide. Lastly the cross-member can be attached at the approximate horizontal mid-point (125mm internal spacing). 20cm Legs are mounted horizontally outside the frame for stability. The frame with mounted motors becomes back-heavy so I personally offset the legs to favor the back side for better support.

Frame Dimensions

Power Supply

Picking the right power-supply is an important aspect of any Stepper Motor configuration. For this machine I used a 12v 15A capable power supply. This provided all of the power I needed to run both motors and the arduino electronics.

3D Printing

Several of the STL designs need supports to be printed to ensure they are printed correctly. NOTE: There are two Cut Heads. One for Resistors and one for LEDs.

Assembly

Here is what you are building:

  • Build the Framework as described above.

  • Attach the AcrylicCutHead on the Back Side of the machine

  • Attach a RazorBlade to the Printed CutHead on the outside

    • Bottom Screw goes THRU the hole on the blade
    • Top Screw squeezes the blade to the head using a washer
  • Attach the Razor CutHead to the Slider Rail

  • Attach the FeedHead to the center rails (Horizontal and Vertical)

    • Align the razor to the slit of the Feedhead
  • Attach and Connect the Display (See connections diagram)

Firmware and Flashing

The Firmware is available in the repo. Use the Arduino IDE application to program the Arduino board. There are several sources of documentation or videos that can instruct you on how to install and use this program. If you have issues, limited technical support is available on the <a href=https://discord.gg/saintcon>SAINTCON Discord Server #minibadge-creators

You will need to install the following libraries:

  • Adafruit GFX
  • Adafruit SSD1306 Display

Board Type should be Arduino Uno (R3)

Open the CuttingMachine_Firmware.ino in the Arduino IDE program Compile and upload the Firmware using the appropriate COM Port

Connections

Connections for all of the components are outlined in the diagram below.

Electrical Connections

PCB Boards

The PCB Boards Gerbers are included in this repo. The following instructions will help you assemble the boards and connect them properly.

Button_Board
  • R1, R2, R3, R4 are all 10k Ohm resistors.
  • Buttons are THT 6mm Momentary Switch.
  • Right-angle PIN HEADERS are suggested exiting out the back.
  • Use a Solder Jumper to connect either 5v or 3v3. (Recommended you use 3v3)
  • Attach the Board with M2 Screws/Bolts to the Display Controller.
  • Attach the Connectors to CNC Shield as labeled in the Connections Diagram.
Sensor_Board
  • R1 is 10K Ohm
  • R2 is 470 Ohm (if using it as presence sensor)
  • R2 is 2.2K Ohm (If used as tape position sensor)
  • PIN HEADERS are 3 Position
  • Attach the Board with the M5 Screw to the FeedHead

Parts

10
QtyValueFootprintReferences
4PULLUPResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1, R2, R3, R4
1BACKButton_Switch_THT:SW_PUSH_6mm_H4.3mmBACK
1Conn_01x07_PinConnector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_VerticalJ2
1DOWNButton_Switch_THT:SW_PUSH_6mm_H4.3mmSW3
1SELECTButton_Switch_THT:SW_PUSH_6mm_H4.3mmSELECT
1SolderJumper_3_OpenJumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabelsPULLUP VOLTAGE
1UPButton_Switch_THT:SW_PUSH_6mm_H4.3mmUP

More from utahsaint-org/CutMachineSMD

1
  • 2 layers20 × 25 mmSensor, the printed circuit board in 3D

    Sensor

    utahsaint-org/CutMachineSMD

    The Resistor and LED Cutting machine is a community project to make mass-production of small SMD components cut to specific unit sizes faster and easier to make for our highly popular MiniBadge initiatives and…

    4 parts4

Similar boards

  • 2 layers57 × 55.2 mmLogicAnalyzer, the printed circuit board in 3D

    LogicAnalyzer

    gusmanb/logicanalyzer

    24 channel, 100Msps logic analyzer hardware and software

    10 parts5.1kGPL-3.0
  • 2 layers32.2 × 15.4 mmProtector, the printed circuit board in 3D

    Protector

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    10 parts4.3kMIT
  • 2 layers26 × 18 mmConn, the printed circuit board in 3D

    Conn

    yaqwsx/KiKit

    Automation tools for KiCAD

    10 parts2.1kMIT
  • 2 layers44.3 × 30.5 mmLime2-SATA RevA, the printed circuit board in 3D

    Lime2-SATA RevA

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    10 parts1.5k
  • 2 layers17.8 × 43.2 mmNano Adapter, the printed circuit board in 3D

    Nano Adapter

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    10 parts1.1kGPL-3.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    10 parts1kGPL-3.0

Questions

How big is the CutMachine PCB PCB?

It measures 54.9 × 34.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the CutMachine PCB use?

10 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the CutMachine PCB KiCad files?

From the utahsaint-org/CutMachineSMD repository on GitHub, at the commit this page was made from: the board is CuttingMachine_PCB/Buttons/CutMachine_PCB.kicad_pcb and its schematic CuttingMachine_PCB/Buttons/CutMachine_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the CutMachine PCB design in my own project?

Its repository states no licence, so its author keeps all rights: ask utahsaint-org before reusing the design.