
Encoder
byrantech/laptop
anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

2-channel multipoint Fast-mode differential I2C-bus
Pca9615 is an open-source printed circuit board by u-fire, from the u-fire/PCA9615-ato repository on GitHub. It is a 2-layer board with 7 parts on 10 nets, routed with 47 tracks and 12 vias.
Its parts include 6 resistors and 1 IC.
This repository is an atopile module for the PCA9615, 2-channel multipoint Fast-mode differential I2C-bus. In other words, it lets you use I2C like you might use MODBUS, ie. over long wires and through noisy environments.
From inside a project directory terminal: ato install PCA9615-ato
from "pca9615/elec/src/pca9615.ato" import PCA9615
from "generics/interfaces.ato" import DiffPair, Power, I2C, GPIO
module Test:
# define virtual buses, connect these to physical components/pins
power = new Power
d_sda = new DiffPair
d_scl = new DiffPair
i2c = new I2C
power_a_2v3_5v5 = new Power
power_b_3v0_5v5 = new Power
differential_side_power = new Power
en = new GPIO
# define the PCA9615
pca9615 = new PCA9615
# PCA9615 enable pin is driven high be an internal pullup
# to disable chip, drive low
en ~ pca9615.en
# connect power to normal I2C side
power_a_2v3_5v5 ~ pca9615.power_a_2v3_5v5
6 in KiCAD PCB Editor)| MCU | MCU PCA9615 | Sensor PCA9615 | Sensor | |||
|---|---|---|---|---|---|---|
| MCU PCA9615.d_SDA 🟩 | ~ | 🟩 PCA9615.d_SDA | ~ | |||
| MCU PCA9615.d_SCL 🟪 | ~ | 🟪 PCA9615.d_SCL | ~ | |||
| MCU.SDA 🟨 | ~ | 🟨 PCA9615.SDA 🟨 | 🟨 PCA9615.SDA | ~ | 🟨 Sensor.SDA | |
| MCU.SCL 🟦 | ~ | 🟦 PCA9615.SCL 🟦 | 🟦 PCA9615.SCL | ~ | 🟦 Sensor.SCL | |
| MCU.VCC 🟥 | ~ | 🟥 PCA9615.VCC 🟥 | (optional) | 🟥 PCA9615.VCC | ~ | 🟥 Sensor.VCC |
| MCU.GND⬛ | ~ | ⬛ PCA9615.GND ⬛ | (optional) | ⬛ PCA9615.GND | ~ | ⬛ Sensor.GND |
Once connected, the sensor (or just the other side) appear as a normal I2C device to the host. Nothing special needs to be done.
This design is intended to be a community best-effort at a minimal circuit combining:
You are greatly encouraged to contribute or discuss any improvements here so that everyone may benefit.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | Chip Resistor - Surface Mount 300Ohms ±5% 1/10W 0603 RoHS | lib:R0603 | R1, R3, R4, R6 |
| 2 | Chip Resistor - Surface Mount 100Ohms ±5% 1/10W 0603 RoHS | lib:R0603 | R2, R5 |
| 1 | lib:TSSOP-10_L3.0-W3.0-P0.50-LS4.9-BL | U1 |

byrantech/laptop
anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.



AxxAxx/AxxSolder
STM32 Based soldering station for JBC cartridges, 9-24 VDC and USB-PD power


jamro/tiny-engineer
A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

7 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the u-fire/PCA9615-ato repository on GitHub, at the commit this page was made from: the board is elec/layout/default/pca9615.kicad_pcb and its schematic elec/layout/default/pca9615.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask u-fire before reusing the design.