Skip to the content
2 layersPca9615, the printed circuit board in 3D

2-channel multipoint Fast-mode differential I2C-bus

Copper layers
2
Thickness
1.6 mm
Parts
7
Nets
10
Pads
22
Tracks, vias
47, 12
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
1 Mar 2024
Updated
5 Mar 2024

Overview

Pca9615 is an open-source printed circuit board by u-fire, from the u-fire/PCA9615-ato repository on GitHub. It is a 2-layer board with 7 parts on 10 nets, routed with 47 tracks and 12 vias.

Its parts include 6 resistors and 1 IC.

README

README.md

PCA9615

📒 Datasheet

This repository is an atopile module for the PCA9615, 2-channel multipoint Fast-mode differential I2C-bus. In other words, it lets you use I2C like you might use MODBUS, ie. over long wires and through noisy environments.

🏁 Get started

Installation

From inside a project directory terminal: ato install PCA9615-ato

Code

ato
from "pca9615/elec/src/pca9615.ato" import PCA9615
from "generics/interfaces.ato" import DiffPair, Power, I2C, GPIO

module Test:
    # define virtual buses, connect these to physical components/pins
    power = new Power
    d_sda = new DiffPair
    d_scl = new DiffPair
    i2c = new I2C
    power_a_2v3_5v5 = new Power
    power_b_3v0_5v5 = new Power
    differential_side_power = new Power
    en = new GPIO

    # define the PCA9615
    pca9615 = new PCA9615

    # PCA9615 enable pin is driven high be an internal pullup
    # to disable chip, drive low
    en ~ pca9615.en

    # connect power to normal I2C side
    power_a_2v3_5v5 ~ pca9615.power_a_2v3_5v5

🤔 Design Considerations

  • d_sda and d_scl must be routed as differential pairs (6 in KiCAD PCB Editor)
  • power on the I2C side can be separate from the differential side, common grounds are not required
  • the I2C side can accept between 2.3 - 5.5 volts
  • the differential side can accept 3.0 - 5.5 volts
  • an RJ45 connector and CAT6 cable work well for making the connections

🔌 Connections

MCUMCU PCA9615Sensor PCA9615Sensor
MCU PCA9615.d_SDA 🟩~🟩 PCA9615.d_SDA~
MCU PCA9615.d_SCL 🟪~🟪 PCA9615.d_SCL~
MCU.SDA 🟨~🟨 PCA9615.SDA 🟨🟨 PCA9615.SDA~🟨 Sensor.SDA
MCU.SCL 🟦~🟦 PCA9615.SCL 🟦🟦 PCA9615.SCL~🟦 Sensor.SCL
MCU.VCC 🟥~🟥 PCA9615.VCC 🟥(optional)🟥 PCA9615.VCC~🟥 Sensor.VCC
MCU.GND⬛~⬛ PCA9615.GND ⬛(optional)⬛ PCA9615.GND~⬛ Sensor.GND

⚡ Programming

Once connected, the sensor (or just the other side) appear as a normal I2C device to the host. Nothing special needs to be done.

🙏 Contributing

This design is intended to be a community best-effort at a minimal circuit combining:

  • datasheet reference design
  • readily available components
  • modular and reusable layout

You are greatly encouraged to contribute or discuss any improvements here so that everyone may benefit.

License

CERN-OHL-P v2

Parts

7
QtyValueFootprintReferences
4Chip Resistor - Surface Mount 300Ohms ±5% 1/10W 0603 RoHSlib:R0603R1, R3, R4, R6
2Chip Resistor - Surface Mount 100Ohms ±5% 1/10W 0603 RoHSlib:R0603R2, R5
1lib:TSSOP-10_L3.0-W3.0-P0.50-LS4.9-BLU1

Similar boards

  • 2 layersEncoder, the printed circuit board in 3D

    Encoder

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    7 parts4.3kMIT
  • 2 layers40 × 20 mmSensor smd, the printed circuit board in 3D

    Sensor smd

    scottbez1/splitflap

    DIY split-flap display

    7 parts4.2k
  • 2 layers19.8 × 30 mmZ limit, the printed circuit board in 3D

    Z limit

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    7 parts3.7k
  • 2 layers35.6 × 58.2 mmDisplay Carrier, the printed circuit board in 3D

    Display Carrier

    AxxAxx/AxxSolder

    STM32 Based soldering station for JBC cartridges, 9-24 VDC and USB-PD power

    7 parts1.7kGPL-3.0
  • 2 layers20.3 × 16.3 mmMap MPX, the printed circuit board in 3D

    Map MPX

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    7 parts1.2k
  • 2 layers26 × 44 mmCompact carrier board, the printed circuit board in 3D

    Compact carrier board

    jamro/tiny-engineer

    A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

    7 parts1.1k
  • 2 layers26.4 × 53.8 mmAtari pickup, the printed circuit board in 3D

    Atari pickup

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    7 parts1kGPL-3.0
  • 2 layersRj45 breakout, the printed circuit board in 3D

    Rj45 breakout

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    7 parts990GPL-3.0

Questions

What parts does the Pca9615 use?

7 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pca9615 KiCad files?

From the u-fire/PCA9615-ato repository on GitHub, at the commit this page was made from: the board is elec/layout/default/pca9615.kicad_pcb and its schematic elec/layout/default/pca9615.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pca9615 design in my own project?

Its repository states no licence, so its author keeps all rights: ask u-fire before reusing the design.