

Mostly Eurorack projects
- Size
- 131.8 × 57.6 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 115
- Nets
- 97
- Pads
- 374
- Tracks, vias
- 681, 87
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 16 Jan 2021
- Updated
- 19 Sep 2026
Overview
Rowan is an open-source printed circuit board by tpcarlson, from the tpcarlson/synth-diy repository on GitHub. It is a 2-layer board of 131.8 × 57.6 mm with 115 parts on 97 nets, routed with 681 tracks and 87 vias.
It is built around the RP2040, 74AHCT1G125SE and W25Q32JVSSIQ, with the SK6812 among its other parts. Its parts include 34 capacitors, 17 connectors, 15 resistors, 14 diodes and 10 ICs. It belongs with the audio and music boards and the RP2040 boards of this library.
Main components
4RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)74AHCT1G125SE
SOT-353-40℃~+125℃ 1 1 4.5V~5.5V 4.7ns@5V,50pF 40uA 74AHCT 8mA 8mA Schmitt trigger Tri-State Unidirectional SOT-353 Buffers, Drivers, Receivers, Transceivers ROHSDiodes IncorporatedBuffers, Drivers, Receivers, TransceiversW25Q32JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 133MHz 1uA 2.7V~3.6V 20 Years 32Mbit 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHSK6812
SMD-4P,5.4x5mm-40℃~+85℃ 0.6mA 1.6mm 120° 160mcd~320mcd 1kHz 2000V 280mcd~515mcd 3.7V~5.5V 460nm~470nm 520nm~530nm 620nm~625nm 800Kbit/s 815mcd~1275mcd Built-in power-on reset circuit Semi-transparent lens SMD-4P,5.4x5mm RGB LEDs(Built-in IC) ROHSOPSCO OptoelectronicsRGB LEDs(Built-In IC)
README
vcadsr/README.mdVCADSR
What is this?
Voltage controlled ADSR, using the ElectricDruid EnvGen8 chip. The module provides voltage control over most parameters (Attack, decay, sustain, release, time, level) as well as manual control with sliders. There are also three switches for toggling the mode, linear/exponential, and a fifth stage called "punch" which adds a little bit more to the attack on an envelope.
The mode toggle switch allows for gated looping, just looping (Almost like an LFO), and normal ADSR mode.
How much power does it use?
As measured by the joranalogue Test 3, around 40mA on +12v and 30mA on -12v at peak. The 5v rail is unused.
Where does the design come from?
The schematic is really an extension of the reference design on the ElectricDruid site, with some changes to add LEDs, and cutting features that would otherwise take up more panel space than I was comfortable with - I dropped the attenuators for CV inputs in favour of nice big manual controls with linear potentiometers instead.
Are there any rare/weird parts used?
You'll need one of the EnvGen8 chips in order to make this function at all!
Are there any problems with the design?
Just a couple, which are corrected in the version here. First, the LEDs for gate and trigger had some issues drawing too much power due to an oversight in the schematic. As it turns out LEDs don't really like being driven without a resistor! Second, the panel design had the mode and linear/exponential graphics switched which makes operating it a little bit more confusing than it otherwise ought to be.
These problems are both fixed in the repository right now though, however the fixes are untested. If I make another run of these boards, I will verify that the fix worked and remove this whole section!
Do you have a BOM/Mouser cart/Tayda links?
Sorry, no. Things go out of stock so frequently it'd be a lot of work to keep these up to date. Everything in this project is easy to source though, so you should not have any trouble.
Other resources
- Assembly instructions
- Interactive BOM - This includes pre-soldered SMT parts as well as the through-hole parts. To use this, save the 'raw' view to your computer and open it in a web browser

Parts
115| Qty | Value | Footprint | References |
|---|---|---|---|
| 24 | 100n | Capacitor_SMD:C_0402_1005Metric | C10, C12, C13, C14, C15, C16, C18, C19, C20, C21, C22, C23, C24, C25, C26, C31 +8 |
| 12 | MountingHole | Divergent:3mm-LED-hole | H1, H2, H3, H4, H5, H6, H7, H8, H9, H10, H11, H12 |
| 12 | SK6812 | Divergent:XINGLIGHT-XL-1010RGBC-WS2812B | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12 |
| 6 | 10u | Capacitor_SMD:C_0603_1608Metric | C3, C5, C6, C7, C28, C30 |
| 6 | MountingHole | Divergent:thonkiconn-hole | H25, H26, H27, H28, H29, H30 |
| 4 | 100R | Resistor_SMD:R_0402_1005Metric | R6, R7, R8, R9 |
| 4 | 1k | Resistor_SMD:R_0402_1005Metric | R3, R13, R14, R16 |
| 4 | AudioJack2 | Divergent:QingPu_WQP-PJ398SM_Ground_pin_tweak | J3, J4, J5, J6 |
| 4 | MountingHole | Divergent:panel-mountinghole-m3 | H31, H32, H33, H34 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C11, C17 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R10, R11 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 74AHCT1G125 | Package_TO_SOT_SMD:SOT-353_SC-70-5 | U7, U8 |
| 2 | AudioJack2 | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J7, J8 |
| 2 | Conn_01x03 | Connector_JST:JST_XH_B3B-XH-AM_1x03_P2.50mm_Vertical | J9, J10 |
| 2 | MCP6002-xMS | Package_SO:MSOP-8_3x3mm_P0.65mm | U3, U4 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R15 |
| 1 | 220R | Resistor_SMD:R_0402_1005Metric | R12 |
| 1 | 470n | Capacitor_SMD:C_0402_1005Metric | C29 |
| 1 | 47u | Capacitor_SMD:CP_Elec_5x5.4 | C27 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | Conn_01x03 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J15 |
| 1 | Conn_01x03 | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J13 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J14 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J12 |
| 1 | Conn_01x08 | Connector_PinSocket_2.54mm:PinSocket_1x07_P2.54mm_Vertical | J17 |
| 1 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J16 |
| 1 | Conn_02x05_Odd_Even | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J11 |
| 1 | Crystal_GND2 | Divergent:CSTNE10M0G55A000R0 | Y2 |
| 1 | DAC7554 | Package_SO:MSOP-10_3x3mm_P0.5mm | U1 |
| 1 | DNF | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | D_Schottky | Diode_SMD:D_SOD-323 | D14 |
| 1 | FerriteBead_Small | Resistor_SMD:R_0805_2012Metric | FB1 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D13 |
| 1 | LM4040LP-5 | Package_TO_SOT_SMD:SOT-23 | U9 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | NCP1117-5.0_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U10 |
| 1 | RP2040 | Raspberry Pi:RP2040-QFN-56 | U6 |
| 1 | SW_Push | Button_Switch_THT:SW_Tactile_Straight_KSA0Axx1LFTR | SW1 |
| 1 | USB_C_Receptacle_USB2.0_16P | Divergent:USB-C-SMD_G-SWITCH_GT-USB-9010AB | J2 |
| 1 | W25Q32JVSS | Package_SON:Winbond_USON-8-1EP_3x2mm_P0.5mm_EP0.2x1.6mm | U5 |
More from tpcarlson/synth-diy
12- 4 layers241.2 × 327.2 mm

- 2 layers293.3 × 128.5 mm

- 4 layers179.5 × 128.5 mm

- 4 layers313.1 × 185.6 mm

- 2 layers85.4 × 128.5 mm

- 2 layers286.9 × 128.7 mm

- 2 layers40.3 × 109.6 mm

- 2 layers191.3 × 128.5 mm

- 4 layers179.1 × 128.5 mm

- 2 layers94.3 × 128.5 mm

- 2 layers101.3 × 128.5 mm

- 2 layers81.1 × 128.5 mm

Similar boards
- 2 layers149 × 224 mm

GDEK
GilDev/GDEK
Low-profile, compact, beginner-friendly, assembly-friendly 4×6 with 5-keys thumb cluster ergonomic keyboard with universal keyswitch support, per-key RGB LED, encoder and RP2040 controller. Phew, that’s a lot!
324 parts3CERN-OHL-S-2.0 - 2 layers90 × 90 mm

Bath monitor
hasebems/bath-monitor
この bath-monitor はそんな家族の問題を解決するために開発しました。 bath-monitor は以下の機能を持っています。 - 家族ごとに5つのボタンを搭載。ボタンが押されると LED が点灯し、ボタンごとに異なるメロディを鳴らす - ボタンの押し間違いがあったら、二秒の長押しで LED は消灯し、キャンセルできる - 照度センサーを搭載し、脱衣所が明るいか暗いかで誰かが入っていることをセンシングする -…
25 parts - 2 layers395.3 × 121.1 mm

- 4 layers51.8 × 68.3 mm

- 2 layers248.6 × 81.9 mm

Alpha curISO
calvin-mcd/alpha-curISO
The Alpha CurISO is a community pcb for the Curio. It supports two different Alpha Staggers and Ortho Layouts. This is a collaboration between jadethemaid, airuei, galvy0 and calvin.
241 parts2 - 2 layers79.2 × 106.7 mm

MacroPad
landodoughty/MacroPad
A Custom Macro Pad I Designed and Built based on the RP2040
111 parts2MIT - 2 layers344.7 × 123.6 mm

- 2 layers158.8 × 100.2 mm

Questions
How big is the Rowan PCB?
It measures 131.8 × 57.6 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Rowan use?
115 parts, built around the RP2040, 74AHCT1G125SE, W25Q32JVSSIQ and SK6812. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rowan KiCad files?
From the tpcarlson/synth-diy repository on GitHub, at the commit this page was made from: the board is rowan/rowan.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rowan design in my own project?
Its repository states no licence, so its author keeps all rights: ask tpcarlson before reusing the design.