Skip to the content
2 layers80 × 42.1 mmMIDI, the printed circuit board in 3D

lighting focused midi controller

Size
80 × 42.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
32
Pads
72
Tracks, vias
54, 4
Pours
4
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
8 Jul 2024
Updated
31 Jan 2025

Overview

MIDI is an open-source printed circuit board by Tommie1236, from the Tommie1236/midi-controller repository on GitHub, published under the CERN-OHL-W-2.0 licence. It is a 2-layer board of 80 × 42.1 mm with 24 parts on 32 nets, routed with 54 tracks and 4 vias.

It is built around the H11L1. Its parts include 9 resistors, 4 connectors, 3 capacitors, 1 IC and 1 diode. It belongs with the audio and music and lEDs and displays boards and the RP2040 boards of this library.

Main components

1

README

README.md

Build firmware Build fader-wing

huge thanks to the amazing rp2040 skeleton project. it helped immensly setting up this project. i probably couldn't have done it without

<still need good name :)>

A lighting focused midi controller

Why?

I started this project as i wanted phisical controls to go with the mydmx3 dmx controller software.
Mydmx3 practicly only support midi as data in/out next to dmx out. So a midi controller it is.
There are more than enough midi controllers on the market but almost all of them are audio focused in the controls. I couldn't really vind any that i would like for controlling lighting. So i decided to design and build my own.

Requirements

I set a couple of requirements that i definetly wanted in my controler. As following:

Controls:
  • motorized faders. Mostly for dimming controls, enough in the playback section and 1 as Master.
    I chose motorized so they could sync with the controlling software if the value changes and for for example if you were to switch banks to a new set of controls. (mydmx doesn't support that but i wanted to design my controller to work with almost anything.)

  • Buttons. for playbacks/executors en general control, a whole lot.
    Of Course. what would a controller be without a lot of buttons. I also want them to have black with transparent text keycaps and rgb leds below to show the status of the button.

  • Encoders. Mostly speed control but could also be dimmer, at least 1 per "channel"/collumn and a couple spare. I wanted some encoders to be able to change the speed of scene/cue playbacks. But also for for example a dimmer channel dat isn't changed often but often enough to have phisical controls for.

  • Small Displays/Scribble Strips. channel/collumn names, one per channel/collumn.
    To show what cue/scene was mapped to that channel/collumn. If i implement bank switching inside the controller (as mydmx doesn't support like anything. only the most basic midi triggering) i want to see what cue i have mapped on that fader/buttons. And maybe also to show the fader/encoder value when changing. For if you want it to a specific value and the visual position isn't enough.

  • Keypad. just one, numbers 0-9 + some modifiers.
    Should speak for itself. just general number inputs and modifiers.

  • "Master" Display. (relatively) big display, just one.
    A around 3a4" touch display for configuration of the controller and general info. Main controls for anything happening inside the controller.

  • Leds. A lot. most RGB some just Amber.
    I want all the buttons to have a seperate controllable RGB led to show the buttons status. and about 16 mono Amber leds around the encoders to show their value.

Conectivity:
  • usb midi. one usb-B port. To connect to a pc running for example mydmx.

  • hardware midi. 2 or 3 din-5 ports. To connect to other midi gear or any controller that has hardware midi ports on it. Should have the same data as the usb midi port

  • External Switch Ports. 2a3 x 1/4" jack. To connect external footswitches or pedals. should support normal on/off footswitches and maybe one or 2 can have analog value support.

  • Desk Light. xlr-4?. A xlr connector that support a lot of desk lights. preferably xlr-4 so it isn't confused with audio or dmx signals. Sadly there isn't a standard for desk ligths as far as i can find.

  • Powercon Socket. Blue one. maybe also power out.
    Of cource. It needs some power to run. prefereably powercon (true1??) but a C14 socket would also work.
    with the motor faders and a lot of leds. Usb supplied power wont be enough.

And here are some features i want to support but arent required for the mvp:
  • USB Hub. Probably USB-A sockets.
    To connect more devices downstream from the controller

  • RTP MIDI. Wifi/Ethernet
    Using a ESP32 or similar to handle the network stack and enable the controller to communicate either wireless or via a ethernet cable.
    Adding to the already available midi connection options of USB-MIDI and hardware-MIDI

  • Web Server.
    Maybe a configuration webserver as the display will be quite small. would also run on the ESP32 that handels the network.
    it connects to the main rp2040 using uart.

Parts

24
QtyValueFootprintReferences
61K@100MHzInductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolderFB1, FB2, FB3, FB4, FB5, FB6
3100nfCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC29, C30, C31
310KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR33, R34, R35
3DIN-5_180degreepersonal:DIN5-180J5, J6, J7
210Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR15, R17
233Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR14, R16
11N914Diode_SMD:D_SOD-523D1
1220Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR13
1470Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR18
1Conn_01x07_SocketConnector_JST:JST_PH_B7B-PH-K_1x07_P2.00mm_VerticalJ9
1H11L1Package_DIP:DIP-6_W7.62mmU5

More from Tommie1236/midi-controller

3
  • 4 layers123.8 × 362.3 mmMidi controller, the printed circuit board in 3D

    Midi controller

    Tommie1236/midi-controller

    lighting focused midi controller

    516 parts2CERN-OHL-W-2.0
  • 2 layers160.5 × 288 mmFaders, the printed circuit board in 3D

    Faders

    Tommie1236/midi-controller

    lighting focused midi controller

    348 parts2CERN-OHL-W-2.0
  • 2 layers250 × 189 mmKeypad, the printed circuit board in 3D

    Keypad

    Tommie1236/midi-controller

    lighting focused midi controller

    76 parts2CERN-OHL-W-2.0

Similar boards

  • 4 layers60 × 94 mmDaisySeedPedal125b, the printed circuit board in 3D

    DaisySeedPedal125b

    bkshepherd/DaisySeedProjects

    A collection of hardware and software projects based around the Electro-Smith Daisy Seed

    80 parts559MIT
  • 2 layers245.2 × 100 mmV5 main, the printed circuit board in 3D

    V5 main

    zynthian/zynthian-hw

    Zynthian hardware stuff: PCBs, schemes, parts specifications, pin assignment, ...

    160 parts156
  • 2 layers64.3 × 56 mmMt32-pi midi hat, the printed circuit board in 3D

    Mt32-pi midi hat

    chris-jh/mt32-pi-midi-hat

    A Raspberry Pi Midi Hat for the project mt32-pi by Dale Whinham (https://github.com/dwhinham/mt32-pi)

    22 parts139GPL-3.0
  • 2 layers100 × 100 mmYM2612 MIDI SMD, the printed circuit board in 3D

    YM2612 MIDI SMD

    superjoebob/genny

    YM2612/SN76489 Virtual Instrument

    112 parts96
  • 2 layers152.4 × 68.6 mmPico test synth2, the printed circuit board in 3D

    Pico test synth2

    todbot/pico_test_synth

    Simple board to help make synths with Raspberry Pi Pico/Pico2 and PCM5102 I2S DAC

    55 parts57MIT
  • 2 layers51.3 × 96.2 mmMinisynth32, the printed circuit board in 3D

    Minisynth32

    grantek/minisynth32

    A 3D-printable MIDI synthesiser inspired by the Roland MT-32 and clumsyMIDI, and powered by the mt32-pi MT-32 emulator.

    32 parts45CC-BY-SA-4.0
  • 2 layers13 × 1.4 mmPicoX7, the printed circuit board in 3D

    PicoX7

    SloeComputers/picoX7

    Software simulation of the Yamaha DX7 with a MIDI interface for the Raspberry Pi Pico

    31 parts43MIT
  • 4 layers71 × 100 mmOscar components, the printed circuit board in 3D

    Oscar components

    dchwebb/Oscar

    Eurorack 3 Channel Oscilloscope based on ARM STM32F446 MCU

    71 parts42Unlicense

Questions

How big is the MIDI PCB?

It measures 80 × 42.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the MIDI use?

24 parts, built around the H11L1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MIDI KiCad files?

From the Tommie1236/midi-controller repository on GitHub, at the commit this page was made from: the board is kicad/MIDI.kicad_pcb and its schematic kicad/Fader-Leds.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MIDI design in my own project?

Its repository publishes it under the CERN-OHL-W-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).