

Atmegax8 with F-3188
AVR alternative to vwcdpic HW+SW
- Size
- 41.4 × 36.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 76
- Nets
- 64
- Pads
- 227
- Tracks, vias
- 642, 46
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20200518)
- Created
- 13 Oct 2015
- Updated
- 4 Oct 2026
Overview
Atmegax8 with F-3188 is an open-source printed circuit board by tomaskovacik, from the tomaskovacik/vwcdavr repository on GitHub. It is a 2-layer board of 41.4 × 36.1 mm with 76 parts on 64 nets, routed with 642 tracks and 46 vias.
It is built around the ATMEGA88A-AU and MAX809S. Its parts include 29 resistors, 28 capacitors, 10 connectors, 4 ICs and 3 diodes. It belongs with the AVR (ATmega, ATtiny) and FPGA and CPLD boards of this library.
Main components
2ATMEGA88A-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 512Byte 8 Bit 8KB AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)MAX809S
SOT-23-40℃~+125℃ 1 140ms 1V~5.5V 2.93V 8uA Active Low Push-pull Voltage Detector SOT-23 Supervisor and Reset ICs ROHSUMWSupervisor And Reset ICs
README
HW/arduino_based_cdc_emulator/atmegax8_with_BM20/README.mdParts
76| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitors_SMD:C_0805_HandSoldering | C1, C2, C3, C4, C5, C7, C8, C12, C24, C25, C28 |
| 6 | 47k | Resistors_SMD:R_0805_HandSoldering | R11, R12, R15, R18, R22, R24 |
| 4 | 22k | Resistors_SMD:R_0805_HandSoldering | R8, R20, R21, R23 |
| 4 | 33p | Capacitors_SMD:C_0805_HandSoldering | C15, C16, C17, C18 |
| 3 | 10m/16V | Capacitors_SMD:c_elec_5x5.8 | C6, C20, C21 |
| 3 | 3k3 | Resistors_SMD:R_0805_HandSoldering | R1, R2, R4 |
| 2 | 100 | Resistors_SMD:R_0805_HandSoldering | R3, R7 |
| 2 | 100k | Resistors_SMD:R_0805_HandSoldering | R16, R17 |
| 2 | 1k | Resistors_SMD:R_0805_HandSoldering | R26, R31 |
| 2 | 1k2 | Resistors_SMD:R_0805_HandSoldering | R25, R27 |
| 2 | 1u/10V | Capacitors_SMD:C_1206_HandSoldering | C23, C27 |
| 2 | 330 | Resistors_SMD:R_0805_HandSoldering | R13, R14 |
| 2 | 39R | Resistors_SMD:R_0805_HandSoldering | R9, R10 |
| 2 | 47m/25V | Capacitors_SMD:c_elec_6.3x5.7 | C9, C14 |
| 2 | LED | LEDs:LED_0805_HandSoldering | D2, D3 |
| 2 | MAX809 | TO_SOT_Packages_SMD.pretty:SOT-23 | U4, U5 |
| 1 | 100m/16V | Capacitors_Tantalum_SMD:CP_Tantalum_Case-D_EIA-7343-31_Hand | C11 |
| 1 | 100u/16V | Capacitors_Tantalum_SMD:CP_Tantalum_Case-D_EIA-7343-31_Hand | C10 |
| 1 | 10k | Resistors_SMD:R_0805_HandSoldering | R28 |
| 1 | 10m/16V | Capacitors_SMD:CP_Elec_5x5.8 | C19 |
| 1 | 10n | Capacitors_SMD:C_0805_HandSoldering | C26 |
| 1 | 16MHz | modules:MURATA_CSTCE_V53 | Y1 |
| 1 | 1M | Resistors_SMD:R_0805_HandSoldering | R6 |
| 1 | 1N4148 | Diodes_SMD:D_MiniMELF | D1 |
| 1 | 20 | Resistors_SMD:R_0805_HandSoldering | R5 |
| 1 | 2m2/16V | Capacitors_Tantalum_SMD:TantalC_SizeA_EIA-3216_HandSoldering | C13 |
| 1 | 330u | SMD_Packages:SMD-1210_Pol | L1 |
| 1 | 4k7 | Resistors_SMD:R_0805_HandSoldering | R19 |
| 1 | 4u7/10V | Capacitors_Tantalum_SMD.pretty:TantalC_SizeA_EIA-3216_Wave | C22 |
| 1 | ATMEGA88-A | Housings_QFP:TQFP-32_7x7mm_Pitch0.8mm | IC1 |
| 1 | CLK | modules:1pin_smd | J4 |
| 1 | CONN_10 | Pin_Headers:Pin_Header_Straight_1x12_Pitch2.54mm | P1 |
| 1 | CONN_4 | Pin_Headers.pretty:Pin_Header_Straight_1x03 | P5 |
| 1 | CONN_4 | Pin_Headers.pretty:Pin_Header_Straight_1x04 | P3 |
| 1 | CSB | modules:1pin_smd | J3 |
| 1 | F-6188 | modules:F-6188_nosilk | U2 |
| 1 | MISO | modules:1pin_smd | J2 |
| 1 | MOSI | modules:1pin_smd | J5 |
| 1 | SERIAL | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | P4 |
| 1 | SPI | Pin_Headers:Pin_Header_Straight_2x03 | P2 |
| 1 | SPI_PCM | modules:1pin_smd | J1 |
More from tomaskovacik/vwcdavr
2- 2 layers41.4 × 36.1 mm

- 2 layers43.4 × 30.4 mm

Similar boards
- 2 layers85.1 × 62.2 mm

Mic extension board
StoneRose35/cortexguitarfx
guitar effects processor implemented on various arm cortex platforms
75 parts146 - 2 layers

- 2 layers27.5 × 0 mm

Thermocouple
Miceuz/thermocouple-modbus
Thermocouple frontend accessible via industrial modbus protocol
75 parts2 - 2 layers99.6 × 99.6 mm

Karabas nano revJ
Vakon84/karabas-nano
ZX Spectrum compatible machine with real Z80 CPU and all logic inside the CPLD Altera EPM3256ATC144 (or EPM7512).
162 parts1WTFPL - 2 layers65 × 107.5 mm

- 2 layers22.4 × 29.8 mm

- 4 layers70 × 89.2 mm

- 2 layers170.2 × 218.4 mm

Questions
How big is the Atmegax8 with F-3188 PCB?
It measures 41.4 × 36.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Atmegax8 with F-3188 use?
76 parts, built around the ATMEGA88A-AU and MAX809S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Atmegax8 with F-3188 KiCad files?
From the tomaskovacik/vwcdavr repository on GitHub, at the commit this page was made from: the board is HW/arduino_based_cdc_emulator/atmegax8_with_F-3188/atmegax8_with_F-3188.kicad_pcb and its schematic HW/arduino_based_cdc_emulator/atmegax8_with_BM20/atmegax8_with_BM20.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Atmegax8 with F-3188 design in my own project?
Its repository states no licence, so its author keeps all rights: ask tomaskovacik before reusing the design.