

PiPower
Open Source Lab Power Supply
- Size
- 55.1 × 29.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 27
- Nets
- 43
- Pads
- 106
- Tracks, vias
- 174, 14
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 15 Dec 2015
- Updated
- 15 Feb 2022
Overview
PiPower is an open-source printed circuit board by tom-biskupic, from the tom-biskupic/LabPSU repository on GitHub. It is a 2-layer board of 55.1 × 29.2 mm with 27 parts on 43 nets, routed with 174 tracks and 14 vias.
It is built around the BC847, 1N4148WS and BC817, with the BC857 and IRLTS2242TR among its other parts. Its parts include 10 resistors, 7 connectors, 5 transistors, 3 diodes and 1 capacitor. It belongs with the power boards of this library.
Main components
5BC847
SOT-231 NPN 100MHz 100mA 100nA 110 200mW 45V 500mV 6V NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching DiodesBC817
SOT-231 NPN 100nA 150MHz 300mW 40 45V 500mA 5V 700mV NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)BC857
SOT-231 PNP 100MHz 100mA 15nA 200mW 45V 5V 650mV 800 PNP SOT-23 Bipolar (BJT) ROHSSTMicroelectronicsBipolar (BJT)IRLTS2242TR
SOT23-6-20V -6.9A P-Channel HEXFET Power MOSFETInfineon TechnologiesUncategorised
README
README.mdLabPSU
Open Source Lab Power Supply
This project is to create an open source modular lab power supply. The power supply is designed to:
- Provide between 0-15V @ 5A and 15-30V @ 3A
- Provide current limiting
- Voltage to be settable to within 1mV and current limit to 1mA resolution.
- Voltage/current readback to 1mV and 1mA with low temperature drift.
- Limit heat loss through the use of a pre-regulator. The pre-regulator uses an SCR and MOSFET arrangement to reduce noise (switches at a low frequency)
- Digitally controllable via a Raspberry PI and touch-screen interface.
- Multiple channels (designed for 3).
- Each channel is isolated and can be paralleled or put in series.
- Each channel uses its own torroidal transformer.
A Blog documenting the development of the project can be found here http://wahz.blogspot.com.au/2015/03/lab-power-supply-project.html
The major components used in the project are:
- IRFP044N N-channel MOSFET as the pass device. http://www.irf.com/product-info/datasheets/data/irfp044n.pdf
- IRF5210 P-channel MOSFET used to switch the input in the pre-regulator http://www.irf.com/product-info/datasheets/data/irf5210.pdf
- MCR-100 SCR http://www.onsemi.com/pub_link/Collateral/MCR100-D.PDF
- LT1639 Op Amps used in the control loop. http://www.linear.com/product/LT1639
- LT1716 Comparator used in the pre-regulator http://cds.linear.com/docs/en/datasheet/1716fa.pdf
- LTC2050 Op Amp used for current sense amplifier. http://www.linear.com/product/LTC2050
- AD5689R DAC with built in 2ppm/degree reference as main output voltage/current DAC. http://www.analog.com/media/en/technical-documentation/data-sheets/AD5689_5687.pdf
- AD7705 ADC used to read output voltage/current http://www.analog.com/media/en/technical-documentation/data-sheets/AD7705_7706.pdf
- ATMEGA328P Used as the main controller
- ADUM1201 dual channel isolator used to isolate the USB interface from the rest of the module http://www.analog.com/media/en/technical-documentation/data-sheets/ADuM1200_1201.pdf
- MCP2200 USB to serial converter http://www.microchip.com/wwwproducts/devices.aspx?dDocName=en546923
Parts
27| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10K | Resistors_SMD:R_0805 | R3, R4, R5 |
| 2 | 1K | Resistors_SMD:R_0805 | R2, R6 |
| 2 | 2K2 | Resistors_SMD:R_0805 | R8, R10 |
| 2 | BC847 | TO_SOT_Packages_SMD:SOT-23 | Q4, Q5 |
| 2 | CONN_01X04 | PinHead1-4:PINHeader1-4 | P2, P6 |
| 1 | 1M | Resistors_SMD:R_0805 | R7 |
| 1 | 1N4007 | Diodes_ThroughHole:Diode_DO-41_SOD81_Horizontal_RM10 | D3 |
| 1 | 1N4148WS | Diodes_SMD:SOD-323 | D1 |
| 1 | 2.2u | Capacitors_SMD:C_0805 | C1 |
| 1 | 470R | Resistors_SMD:R_0805 | R9 |
| 1 | 4K7 | Resistors_SMD:R_0805 | R1 |
| 1 | BC817 | TO_SOT_Packages_SMD:SOT-23 | Q1 |
| 1 | BC857 | TO_SOT_Packages_SMD:SOT-23 | Q3 |
| 1 | BoostConverter | BoostConverter:BoostConverter | U1 |
| 1 | CONN_01X02 | Pin_Headers:Pin_Header_Straight_1x02 | P7 |
| 1 | CONN_01X02 | wcon:WCON-2PIN | P5 |
| 1 | CONN_01X02 | PinHead1-4:TwoPinSmall | P4 |
| 1 | CONN_01X03 | PinHead1-4:ThreePinSmall | P1 |
| 1 | CONN_02X20 | Pin_Headers:Pin_Header_Straight_2x20 | P3 |
| 1 | D | Diodes_SMD:SOD-323 | D4 |
| 1 | IRLTS2242 | tsop-6:TSOP-6 | Q2 |
More from tom-biskupic/LabPSU
3- 2 layers128 × 80 mm

- 2 layers192.5 × 85 mm

- 2 layers75 × 46 mm

Similar boards
- 4 layers190 × 135 mm

- 2 layers28 × 100 mm

- 4 layers124.6 × 68.7 mm

- 2 layers200 × 100 mm

Polykit x monosynth
polykit/polykit-x-monosynth
The Polykit X1 is a DIY semi-modular, analog, patchable synthesizer
167 parts94 - 2 layers91.2 × 48.3 mm

- 4 layers48.2 × 46.2 mm

- 2 layers281.1 × 236.5 mm

MiniDrumkit2
Fihdi/MiniDrumkit
Eurorack DrumKit module with a 3 channel wave-file player and analog Hi-Hat and Kick Drum sections
239 parts15MIT - 2 layers147.3 × 95.3 mm

Nixie proj conflict-20171112-163801
dm2lct/tlnixie
PCB files for the Turmlabor nixie clock 2.0
117 parts11GPL-3.0
Questions
How big is the PiPower PCB?
It measures 55.1 × 29.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the PiPower use?
27 parts, built around the BC847, 1N4148WS, BC817 and BC857. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PiPower KiCad files?
From the tom-biskupic/LabPSU repository on GitHub, at the commit this page was made from: the board is KiCAD/PiPower/PiPower.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the PiPower design in my own project?
Its repository states no licence, so its author keeps all rights: ask tom-biskupic before reusing the design.