

Measure surfing characteristics
- Size
- 22.6 × 35.1 mm
- Copper layers
- 2
- Thickness
- 0.59 mm
- Parts
- 68
- Nets
- 112
- Pads
- 346
- Tracks, vias
- 0, 0
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 2 Apr 2025
- Updated
- 3 Jun 2025
Overview
TRAX is an open-source printed circuit board by thesunRider, from the thesunRider/TRAX repository on GitHub. It is a 2-layer board of 22.6 × 35.1 mm with 68 parts on 112 nets.
It is built around the ESP32-S3-WROOM-1-N8, ZOE-M8Q-0 and AMS1117-3.3, with the AXP2101, BNO080 and WS2812B among its other parts. Its parts include 31 capacitors, 16 resistors, 5 ICs, 5 diodes and 4 inductors. It belongs with the ESP32 boards of this library.
Main components
6ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesZOE-M8Q-0
SMD-51P-160dBm -40℃~+85℃ 2.7V~3.6V Dual-band / multi-band positioning GPS、BeiDou、Galileo、GLONASS UART、I2C、SPI SMD-51P GNSS Modules ROHSu-bloxGNSS ModulesAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAXP2101
QFN-40-EP(5x5)-40℃~+85℃ 3.9V~5.5V Dynamic voltage scaling、Overcurrent Protection、Operating status indication、Adjustable current limiting、Power-on timing control QFN-40-EP(5x5) Power Management - Specialized ROHSX-Powers TechPower Management - SpecializedBNO080
LGA-28(5.2x3.8)-40℃~+85℃ 1.5uA、1.9uA 1.65V~3.6V、2.4V~3.6V 12bit、16bit IMU (accelerometer + gyroscope) Motion event detection、Synchronization and timestamp SPI、I2C、UART X,Y,Z X,Y,Z ±2000dps ±8g LGA-28(5.2x3.8) Accelerometers ROHSCEVAAccelerometersWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
README.mdmain
Parts
68| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100n | Capacitor_SMD:C_0805_2012Metric | C2, C4, C5, C7, C8, C26, C28, C29 |
| 8 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R5, R14, R15, R16, R17, R18, R19 |
| 6 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C12, C13, C16, C18, C22, C23 |
| 5 | 1u | Capacitor_SMD:C_0805_2012Metric | C1, C3, C6, C24, C25 |
| 5 | 22u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9, C15, C19, C20, C21 |
| 5 | 4.7k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4, R6, R7, R11 |
| 3 | SD05_SOD323 | Diode_SMD:D_SOD-323 | D2, D3, D5 |
| 2 | 0 | Resistor_SMD:R_1206_3216Metric | NC1, NC2 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric | C14, C17 |
| 2 | 1u | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L1, L2 |
| 2 | 22p | Capacitor_SMD:C_0805_2012Metric | C30, C31 |
| 2 | 32.768Khz Crystal | Crystal:Crystal_SMD_Abracon_ABM3-2Pin_5.0x3.2mm | Y1, Y2 |
| 1 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10 |
| 1 | 100n | Capacitor_SMD:C_0402_1005Metric | C11 |
| 1 | 10u | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L3 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10 |
| 1 | 2.2u | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L4 |
| 1 | 4.7u | Capacitor_SMD:C_0805_2012Metric | C27 |
| 1 | 510 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | AXP2101 | Package_DFN_QFN:QFN-40-1EP_5x5mm_P0.4mm_EP3.6x3.6mm | U3 |
| 1 | BNO080 | Package_LGA:LGA-28_5.2x3.8mm_P0.5mm | U5 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U2 |
| 1 | LED | LED_SMD:LED_0402_1005Metric | D4 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_B3S-1000 | SW1 |
| 1 | U.FL-R-SMT_01_ | U.FL-R-SMT_01_:HRS_U.FL-R-SMT_01_ | J2 |
| 1 | USB_C_Plug_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | P1 |
| 1 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1 |
| 1 | ZOE-M8Q | RF_GPS:ublox_ZOE_M8 | U4 |
Similar boards
- 4 layers40 × 30 mm

- 4 layers38 × 64 mm

Ak display 38x64 SPLIT POWER CANDIDATE
LeeSpo/portable-display-epass-EVT1-minboot-r1
当前自研硬件为 38 × 64 mm、四层 split-power 工程候选,尚未放行生产。
147 parts - 4 layers27.9 × 55.9 mm

Out
MichalMatu/hardware-lab
Hardware experiments, board bring-up, firmware starters and setup notes
43 parts - 4 layers60 × 60 mm

Rocket payload
Gupatron/Gupsfirstpcb
This is the first pcb that I will manufacture and intend to use for teleop usecases in my personal projects.
138 parts - 4 layers67.4 × 64 mm

- 4 layers73 × 98 mm

ALBERT FLIGHTCOMPUTER
felixznr/ALBERT
Albert I was a rhesus macaque monkey and the first mammal launched on a rocket (V-2 Rocket "Blossom No. 3") on June 18, 1948.
161 partsMIT - 4 layers150 × 137.1 mm

Controller
CircuitGuy943/Sabre-Integrated-flight-controller
(🚧) A "Jack of all trades" custom flight controller board. With support for both power and control and the ability for custom firmware
282 parts2GPL-3.0 - 4 layers54 × 29 mm

Questions
How big is the TRAX PCB?
It measures 22.6 × 35.1 mm and has 2 copper layers, 0.59 mm thick.
What parts does the TRAX use?
68 parts, built around the ESP32-S3-WROOM-1-N8, ZOE-M8Q-0, AMS1117-3.3 and AXP2101. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the TRAX KiCad files?
From the thesunRider/TRAX repository on GitHub, at the commit this page was made from: the board is kicad/main/main.kicad_pcb and its schematic kicad/main/charging.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the TRAX design in my own project?
Its repository states no licence, so its author keeps all rights: ask thesunRider before reusing the design.