

Bionic d8087
Modern platform to run retro CPUs
- Size
- 39.4 × 68.6 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 11
- Nets
- 48
- Pads
- 139
- Tracks, vias
- 279, 21
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 6 Mar 2024
- Updated
- 7 Nov 2026
Overview
Bionic d8087 is an open-source printed circuit board by tgtakaoka, from the tgtakaoka/retro-bionic repository on GitHub. It is a 2-layer board of 39.4 × 68.6 mm with 11 parts on 48 nets, routed with 279 tracks and 21 vias.
It is built around the P8086 and CSL1901UW1. Its parts include 4 capacitors, 3 ICs, 2 connectors, 1 resistor and 1 diode. It belongs with the retro computing and games boards of this library.
Main components
2README
README.mdretro-bionic
Run real vintage CPUs on a modern Cortex-M7 — with a debugger, assembler and disassembler built in.

Contents
- CPUs — every target supported and planned, with the variants each detects
- Hardware — the board stack, signal naming and the awkward chips
- 3.3 V base — planned second base board, its keying and what it unlocks
- Debugger — full command reference
- Build & run — toolchain, flashing, serial ports
- Samples — the programs and how to run them
- CPU speed by an assembly-language Mandelbrot — the benchmark's seconds per frame on each chip
- Demos — recorded terminal sessions, and what to watch for in them
What is this?
Put a real MC6809, Z80, TMS9900 or CDP1802 into a ZIF socket and single-step it, one bus cycle at a time, from a terminal on your desk.
Bionic runs genuine vintage processors — not emulations of them. A Teensy 4.1 is wired to every pin of the target CPU and drives the whole system around it: the clock, every bus cycle, and the memory and peripherals the chip thinks it is talking to. One firmware image — about 470 kB including every assembler, disassembler and debugger — covers all 50 supported targets, and the board tells the controller which one it is.
The hardware is two boards:
- Base — the Teensy 4.1, five TXS0108E level shifters for 3.3 V ↔ 5 V translation, data bus holders, the 48-pin ZIF socket and the HALT/RUN switch.
- CPU adapter — one small board per processor, holding little more than the chip itself, its identity EEPROM and whatever power the part demands. The TMS9900 board, for example, generates its own +12 V and −5 V rails and a non-overlapping four-phase clock, and CPUs with large address spaces carry an address bus multiplexer.

The 48 signals crossing the connector are named P10–P57, and each CPU board maps them to
its own pinout in a small TOML file. See docs/hardware.md.
Debugger features
- Single-step a physical CPU and print every bus cycle it performed (
S). - Live disassembly of the next instruction after each register dump, via libasm.
- Registers read back by injecting instructions and capturing the resulting cycles —
read and write them (
r,=). - Breakpoints, up to 4 plus one temporary for run-until-address (
B,b,g). - Memory dump and patch, separate program and data spaces for Harvard architectures
(
d,p,m,M), plus a write-protect area on targets that need one (P). - Upload Intel HEX or Motorola S-record straight over the serial link (
U). - Emulated peripherals — MC6850 ACIA and i8251 USART — and on-chip serial ports of MCU
targets bridged to your terminal (
I). - Automatic board identification from a UNI/O serial EEPROM, plus runtime variant
detection: one 6502 board reports
MOS6502,G65SC02,R65C02,W65C02SorW65C816Sdepending on which die actually responds.
A real TMS9900 session: registers, disassembly, single-stepping with the bus trace, then drawing the Mandelbrot set.
Supported CPUs
All 50 targets, grouped by vendor and architecture:
| Vendor | Architecture | Targets |
|---|---|---|
| Motorola | 6800 | MC6800 MB8861, MC6801 HD6301, MC6802 MB8870, MC68HC11A, MC68HC11D |
| 6805 | MC146805E2, MC68HC05C0, MC68HC08AZ0 | |
| 6809 | MC6809 HD6309, MC6809E HD6309E | |
| 68HC12 | MC68HC12B | |
| 68HC16 | MC68HC16Z | |
| MOS Technology | 6502 | MOS6502 G65SC02, R65C02, W65C02S, W65C816S |
| Zilog | Z80 | Z80, Z180, NSC800, KL5C80A12, HD64180S |
| Z280 | Z280 | |
| Z380 | Z380 | |
| Z8000 | Z8001, Z8002 | |
| Z8 | Z86C91, Z88C00 | |
| Intel | MCS-48 | P8048 P8039, MSM80C39 |
| MCS-51 | P8051 | |
| MCS-80/85 | P8080, P8085 | |
| MCS-96 | P8095BH, N8097BH, S80C196K S80C196KB, S80C196KC, S80296SA | |
| Texas Instruments | TMS9900 | TMS9900, TMS9980, TMS9981, TMS9995, TMS99105 TMS99110 |
| TMS7000 | TMS7000 TMS7002 | |
| TMS370 | TMS370Cx5x | |
| TMS320 | TMS320C15 | |
| DEC | PDP-8 | IM6100, HD6120 |
| RCA | COSMAC | CDP1802 CDP1804A |
| Fairchild | F8 | F3850 |
| National | SC/MP II | INS8060 |
| SC/MP III | INS8070 | |
| Signetics | 2650 | SCN2650 |
| Toshiba | TLCS-90 | TMP90C802 |
| Hitachi | H16 | HD641016 |
| Panafacom | MN1610 | MN1613 MN1613A |
Targets in italics are variants the firmware identifies at runtime, by executing instructions that behave differently on each die — not by anything written on the board.
See docs/supported-cpus.md for the full table, including the CPUs still to be supported.
Repository layout
| Path | Contents |
|---|---|
debugger/ | Teensy 4.1 firmware — shared framework plus 25 per-family back ends |
schematics/ | KiCad projects: base, mezzanine, PLCC adapter and 54 CPU adapter boards, with gerbers and PDFs |
pinout/ | Pin-map definitions consumed by dip |
samples/ | Test programs — Mandelbrot, arithmetic suites, serial echo — ported to every CPU |
scripts/ | Bench control, regression, cycle recording and timing scripts, and the PlatformIO compile_commands.json helper |
Related projects
| Project | Role |
|---|---|
| libasm | The assembler and disassembler engine — 41 architectures, 119 CPU variants, small enough to run on an AVR |
| libcli | The serial command-line front end the debugger is built on |
| dip | Draws the pinout diagrams from the TOML files in pinout/ |
Resources
- Recorded sessions — asciinema.org/~tgtakaoka
- Progress log — Bluesky · X
License
Licensed under the Apache License, Version 2.0.
Parts
11| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C4 |
| 2 | 22u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C3 |
| 1 | 1.6k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 11AA010-I/TT | microchip:SOT-23_MC_MCH-M | U3 |
| 1 | Bionic-P135 | bionic:Bionic-P135_THT | J1 |
| 1 | Bionic-P245 | bionic:Bionic-P245_THT | J2 |
| 1 | CSL1901UW1 | rhom:LED_CSL1901UW1_ROM-M | D1 |
| 1 | D8087 | bionic:DIP-40_W15.24mm_Socket | U2 |
| 1 | P8086 | bionic:DIP-40_W15.24mm_Socket | U1 |
More from tgtakaoka/retro-bionic
12- 2 layers96.5 × 96.5 mm

- 4 layers30.5 × 88.9 mm

- 2 layers25.4 × 68.6 mm

- 4 layers25.4 × 68.6 mm

- 2 layers25.4 × 68.6 mm

- 4 layers25.4 × 68.6 mm

- 2 layers96.5 × 80 mm

- 2 layers25.4 × 68.6 mm

- 4 layers31.7 × 68.6 mm

- 4 layers31.7 × 68.6 mm

- 4 layers25.4 × 68.6 mm

- 2 layers25.4 × 68.6 mm

Similar boards
- 2 layers22 × 17 mm

- 2 layers60 × 30 mm

Controller
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards
11 parts3kApache-2.0 - 2 layers103 × 30.5 mm

- 2 layers26 × 30 mm

Expansion Card
FrameworkComputer/ExpansionCards
Reference designs and documentation to create Expansion Cards for the Framework Laptop
11 parts1.1kCC-BY-4.0 - 2 layers53.9 × 23.2 mm

Buffer
hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
11 parts1kGPL-3.0 - 2 layers10 × 20 mm

2 connector Sensor Board
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
11 parts915 - 2 layers

- 2 layers47 × 33 mm

Sevensegment led display module
tardate/LittleArduinoProjects
a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!
11 parts803MIT
Questions
How big is the Bionic d8087 PCB?
It measures 39.4 × 68.6 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Bionic d8087 use?
11 parts, built around the P8086 and CSL1901UW1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Bionic d8087 KiCad files?
From the tgtakaoka/retro-bionic repository on GitHub, at the commit this page was made from: the board is schematics/p8086/bionic-d8087.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Bionic d8087 design in my own project?
Its repository states no licence, so its author keeps all rights: ask tgtakaoka before reusing the design.