

ZigbeeRetrofit
Project to retrofit a board into M5Stack case
- Size
- 20 × 50 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 24
- Nets
- 45
- Pads
- 106
- Tracks, vias
- 134, 23
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 14 Aug 2023
- Updated
- 18 Oct 2023
Overview
ZigbeeRetrofit is an open-source printed circuit board by tfindlay-au, from the tfindlay-au/ZigbeeRetrofit repository on GitHub. It is a 2-layer board of 20 × 50 mm with 24 parts on 45 nets, routed with 134 tracks and 23 vias.
It is built around the CC2531F256RHAT, SPX3819M5-L-3-3 and ECS-.327-12.5-34RR-TR, with the LTST-C281KGKT, TC2050-IDC-NL and U.FL-R-SMT-1(10) among its other parts. Its parts include 12 capacitors, 3 connectors, 2 resistors, 2 ICs and 2 inductors.
Main components
6CC2531F256RHAT
VQFN-40-EP(6x6)-40℃~+125℃ -97dBm 2.4GHz 250Kbps 28.7mA 2V~3.6V 4.5dBm 802.15.4 SPI、USART、USB VQFN-40-EP(6x6) RF Transceiver ICs ROHSTexas InstrumentsRF Transceiver ICsSPX3819M5-L-3-3
SOT-23-5-40℃~+85℃@(Ta) 1 20V 3.3V 420mV@(100mA) 500mA 5uA 70dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsECS-.327-12.5-34RR-TR
SMD3215-2P-40℃~+85℃ 12.5pF 32.768kHz 40kΩ ±20ppm SMD3215-2P Crystals ROHSECSCrystalsLTST-C281KGKT
0402-30℃~+85℃ 130° 20mA 2V 35mcd 571nm 574nm 75mW Discrete Diode Water Clear Yellow Green 0402 LED Indication - Discrete ROHSLite-OnLED Indication - DiscreteTC2050-IDC-NL
Connector for plug-of-nails programming cableTag ConnectUncategorisedU.FL-R-SMT-1(10)
SMD-40℃~+90℃ 1 1.25mm 2mm 50Ω 6GHz Board Side IPEX Male Pin SMD Coaxial Connectors (RF) ROHSHirose ElectricCoaxial Connectors (RF)
README
README.mdZigbee Retrofit
Purpose
This project provide a PCB that will retrofit into an M5Stack Zigbee Unit but replaces the CC2630 with the more common and better supported CC2531 chipset.
Designed in KiCad 6.0.9 The output board measures 50mm x 20mm and contains cutouts for mounting in the case /w lego fittings
The design incorporates a Tag-Connect 10 pad pogo pin (TC-2050-NL) footprint to write/flash firmware. The design also incorporates a 4-pin Grove connector with UART interface for easy connection with M5Stack Atom products.
The design also uses the following symbols:
- 110990037: Seed Studio Grove connector
- CC2531F256RHAT: TI Chip Zigbee chip
- TC2050-IDC-NL: 10 pin flash connection
- U.FL-R-SMT-1_10: UFL antenna connector
- ECS-320-13-42-CKM-TR: 32 Mhz Crystal
- ECS-.327-12.5-34RR-TR: 32.768 kHz Crystal
Next Steps
- Add USB port ?
- Add an RF shield to go over the chip
Parts
24| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 15pF | Capacitor_SMD:C_0402_1005Metric | C11, C12 |
| 2 | 18pF | Capacitor_SMD:C_0402_1005Metric | C5, C6 |
| 2 | 1pF | Capacitor_SMD:C_0402_1005Metric | C2, C3 |
| 2 | 22uF | Capacitor_SMD:C_0402_1005Metric | C9, C10 |
| 2 | 27pF | Capacitor_SMD:C_0402_1005Metric | C4, C7 |
| 2 | 2nH | MHQ1005P2N0ST000:INDC1006X60N | L1, L2 |
| 1 | 110990037 | Connector_JST:JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J1 |
| 1 | 150 Ohm | ERJ-2GEJ151X:RES_ERJ-2GEJ151X | R2 |
| 1 | 1uF | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 2.2pF | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | 32 Mhz | ECS-320-13-42-CKM-TR:XTAL_ECS-320-13-42-CKM-TR | Y1 |
| 1 | 56K Ohm | ERJ-2GEJ563X:RES_ERJ-2GEJ563X | R1 |
| 1 | CC2531F256RHAT | CC2531F256RHAT:QFN50P600X600X100-41N | U1 |
| 1 | ECS-.327-12.5-34RR-TR | ECS-.327-12:XTAL_ECS-.327-12.5-34RR-TR | Y2 |
| 1 | LTST-C281KGKT | LTST-C281KGKT:0402(POL) | D1 |
| 1 | SPX3819M5-L-3-3 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | TC2050-IDC-NL | TC2050-IDC-NL:TAG-CONNECT_TC2050-IDC-NL | J3 |
| 1 | U.FL-R-SMT-1(10) | U:HRS_U.FL-R-SMT-1(10) | J2 |
Similar boards
- 4 layers117.5 × 30 mm

- 8 layers

FIRM v1.1
NCSU-High-Powered-Rocketry-Club/FIRM-KiCad
Full and open hardware design for FIRM
108 parts1MIT - 2 layers

Ephemerkey
ephemerkey/ephemerkey
The consumer half of the ephemerkey system, and the second PCB in this repo (alongside hardware/ephemerkey/, sharing the same scripts/kschgen.py engine, Makefile, and lib tables — the multi-project layout used by…
70 parts - 4 layers30 × 40.8 mm

Drone fc
neilpate/Drone
A learning project: build a quadcopter from scratch — own hardware, own firmware, no existing flight stack.
37 partsApache-2.0 - 4 layers46.5 × 40 mm

- 4 layers145 × 57 mm

- 10 layers180 × 100 mm

Jetson agx thor baseboard
antmicro/jetson-agx-thor-baseboard
Open hardware baseboard for Nvidia Jetson Thor AGX T5000 System on Module
1,213 parts48Apache-2.0 - 2 layers

Enlightened Otter
Jana-Marie/Enlightened-Otter
Enlighted-Otter is an Open-Source and OSHW work-light for hacker/maker events like the chaos communication congress, which can be screwed onto a club mate bottle.
182 parts35GPL-3.0
Questions
How big is the ZigbeeRetrofit PCB?
It measures 20 × 50 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ZigbeeRetrofit use?
24 parts, built around the CC2531F256RHAT, SPX3819M5-L-3-3, ECS-.327-12.5-34RR-TR and LTST-C281KGKT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ZigbeeRetrofit KiCad files?
From the tfindlay-au/ZigbeeRetrofit repository on GitHub, at the commit this page was made from: the board is ZigbeeRetrofit.kicad_pcb and its schematic ZigbeeRetrofit.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ZigbeeRetrofit design in my own project?
Its repository states no licence, so its author keeps all rights: ask tfindlay-au before reusing the design.