

Wififem
Miscellaneous RF front-end circuits
- Size
- 40 × 49.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 48
- Nets
- 40
- Pads
- 144
- Tracks, vias
- 262, 173
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171114)
- Created
- 22 Oct 2019
- Updated
- 28 Dec 2020
Overview
Wififem is an open-source printed circuit board by tejeez, from the tejeez/rf-frontends repository on GitHub, published under the MIT licence. It is a 2-layer board of 40 × 49.5 mm with 48 parts on 40 nets, routed with 262 tracks and 173 vias.
It is built around the SE2611T-R, 74HCT04D and MCP6566-E/OT. Its parts include 16 resistors, 14 capacitors, 4 ICs, 4 connectors and 4 inductors.
Main components
3SE2611T-R
QFN-20(3x3)2.4GHz~2.5GHz QFN-20(3x3) RF Front End Circuits ROHSSkyworks SolutionsRF Front End Circuits74HCT04D
SO-14-40℃~+125℃ 1 19ns@4.5V,50pF 2V 2uA 3.7V 4.5V~5.5V 400mV 4mA 4mA 6 74HCT 800mV SO-14 Inverters ROHSNexperiaInvertersMCP6566-E/OT
SOT-23-5-40℃~+125℃ 1 1.8V~5.5V 100uA 1pA 1pA 2.5mV 2uV/℃ 3mV 56ns 66dB Built-in hysteresis Open-drain Rail-to-rail input SOT-23-5 Comparators ROHSMicrochip TechnologyComparators
README
README.mdMiscellaneous RF front-end circuits
Here are the KiCad files for some RF amplifier PCB designs.
Unless otherwise specified, the designs here are under the MIT license.
wififem
This is a 2.4 GHz TX and RX amplifier using a SE2611T WiFi front-end chip. It is intended to go between a LimeSDR and an antenna or a higher-powered WiFi booster amplifier.
It also includes TX/RX switching controlled by a power detector.
SE2611T was chosen because Tommi OH1GJV had several of them as surplus. The design hasn't been tested though, since the components and boards got lost somewhere.
70cm_2W_PA
This is a 400-440 MHz power amplifier using a M68710L RF power module. The module is old but they were really cheap at Lutikoiden tuuletus. With a nominal input power of 20 mW (13 dBm), it can be driven directly from common SDRs.
It is designed to be mounted on a heatsink, transferring heat through the PCB using a grid of vias under the amplifier module. This avoids the mechanical trouble of achieving a good RF contact between the PCB and the heatsink. At low duty cycles, it may even work without a heatsink.
Note that the PCB is 1 mm thick.
Parts
48| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100 | Resistors_SMD:R_0805_HandSoldering | R4, R5, R6, R7, R8, R9, R10 |
| 7 | 100n | Capacitors_SMD:C_0805_HandSoldering | C3, C4, C6, C7, C8, C9, C10 |
| 4 | 10p | Capacitors_SMD:C_0805_HandSoldering | C1, C5, C11, C12 |
| 4 | Mounting_Hole_PAD | Mounting_Holes:MountingHole_3.2mm_M3_Pad | MK1, MK2, MK3, MK4 |
| 3 | 100k | Resistors_SMD:R_0805_HandSoldering | R3, R11, R13 |
| 3 | Conn_Coaxial | Connectors:SMA_THT_Jack_Straight | J1, J2, J3 |
| 3 | ferrite bead | Inductors_SMD:L_0805_HandSoldering | L2, L4, L6 |
| 2 | 10k | Resistors_SMD:R_0805_HandSoldering | R1, R2 |
| 2 | 2u2 | Capacitors_SMD:C_0603_HandSoldering | C13, C14 |
| 1 | 0 | Resistors_SMD:R_0805_HandSoldering | R14 |
| 1 | 0 (lna off) | Resistors_SMD:R_0603 | R15 |
| 1 | 0 (lna on) | Resistors_SMD:R_0603 | R16 |
| 1 | 1p | Capacitors_SMD:C_0805_HandSoldering | C2 |
| 1 | 2.4 GHz choke | Inductors_SMD:L_0805_HandSoldering | L3 |
| 1 | 220k | Resistors_SMD:R_0805_HandSoldering | R12 |
| 1 | 74HCT04 | Housings_SOIC:SOIC-14_3.9x8.7mm_Pitch1.27mm | U2 |
| 1 | AP1117-15 | TO_SOT_Packages_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | Conn_01x05 | Socket_Strips:Socket_Strip_Straight_1x05_Pitch2.54mm | J4 |
| 1 | DIODE | Resistors_SMD:R_0805_HandSoldering | D2 |
| 1 | D_Schottky_x2_KCom_AAK | TO_SOT_Packages_SMD:SOT-23 | D1 |
| 1 | MCP6566 | TO_SOT_Packages_SMD:SOT-23-5_HandSoldering | U1 |
| 1 | SE2611T | Housings_DFN_QFN:UQFN-20-1EP_3x3mm_Pitch0.4mm | U3 |
More from tejeez/rf-frontends
2- 2 layers48.3 × 48.3 mm

- 2 layers81.3 × 35.6 mm

Similar boards
- 2 layers56 × 37.5 mm

Panel proto data slicer board
PantsForBirds/adsbee
Open Source Embedded ADS-B Receiver
216 parts344GPL-3.0 - 2 layers71.9 × 17.5 mm

- 4 layers65 × 100 mm

PGR
Projeto-Guarda-Rios/PCB
O repositório para a PCB do Projeto Guarda Rios! Inclui todos os ficheiros relacionados com a PCB!
167 parts2MIT - 2 layers333.4 × 149.9 mm

- 2 layers297.2 × 180.3 mm

- 2 layers99.1 × 99.7 mm

RC6502 General Video Adapter
tebl/RC6502-Apple-1-Replica
An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!
80 parts193GPL-3.0 - 2 layers99.1 × 49.9 mm

- 2 layers

LM80C R6
leomil72/LM80C
A Z80-based homebrew computer withTMS9918, AY-3-8910, Z80 CTC, Z80 PIO, and Z80 SIO
153 parts123GPL-3.0
Questions
How big is the Wififem PCB?
It measures 40 × 49.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Wififem use?
48 parts, built around the SE2611T-R, 74HCT04D and MCP6566-E/OT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Wififem KiCad files?
From the tejeez/rf-frontends repository on GitHub, at the commit this page was made from: the board is wififem/wififem.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Wififem design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).