

Wrap030 Video
Homebrew 68030 computer
- Size
- 106.7 × 83.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 43
- Nets
- 160
- Pads
- 443
- Tracks, vias
- 957, 329
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 31 May 2021
- Updated
- 13 Aug 2026
Overview
Wrap030 Video is an open-source printed circuit board by techav-homebrew, from the techav-homebrew/Wrap030 repository on GitHub. It is a 2-layer board of 106.7 × 83.8 mm with 43 parts on 160 nets, routed with 957 tracks and 329 vias.
It is built around the YC164-FR-071KL and YC164-FR-0775RL. Its parts include 15 capacitors and 2 ICs. It belongs with the FPGA and CPLD boards of this library.
Main components
2README
README.mdWrap030
An ever-evolving homebrew 68030 computer.
Wrap030 got its name from its beginnings. It started as a wire-wrapped single board computer built largely from parts on-hand and what could be acquired locally. It was incredibly unstable.
Since then, it has gone through several major stages, adding new hardware and updating its memory map along the way. It currently exists as a stack of PCBs with a three ribbon cable main bus linking them. Many odd decisions and design constraints carry forward from that initial wire-wrap prototype.
The primary goal of the project is to learn how to build a 32-bit computer from the ground up, and at that it has been incredibly successful. A secondary long-term goal was to build something capable of running a Unix-like operating system, and has had some success there as well.
A rough log of development is tagged wrap030 on techav.net.
Software
Bootloader
ROM bootloader will read & execute BOOT.BIN from a FAT16-formatted CompactFlash card.
MultiBASIC
MultiBASIC is a minimal just-enough-OS kernel for running 8 simultaneous instances of EhBASIC. It uses the 68030 MMU to implement memory protection and supports pre-emptive multitasking.
NetBSD
In early 2025, the project had finally reached a state where it was stable enough and had all of the critical hardware components to try to port a proper operating system. NetBSD was chosen because of its active m68k development and relative ease of understanding. One month was devoted to attempting to port NetBSD to Wrap030 with the result being a functional single-user root shell. Full multi-user booting was not successful. The results of that work are in a separate repo, netbsd-wrap030.
Hardware
Memory Map
| Address | Device | Size/Stride | IRQ | Description |
|---|---|---|---|---|
| 0x00000000 | RAM | 16MB | Main memory, all of lower 2GB reserved for RAM | |
| 0x80000000 | ROM | 128kB | Boot ROM, up to 512kB supported. Overlays 0x0 on reset | |
| 0x80080000 | ACIA | stride 4 | 1 | M6850 ACIA for bootloader & MultiBASIC supervisor |
| 0x80180000 | Overlay | N/A | Write-only register for disabling startup overlay | |
| 0x80200000 | IDE Cmd | stride 2 | 3 | IDE Command registers |
| 0x80202000 | IDE Ctrl | stride 2 | 3 | IDE Control registers |
| 0x80300000 | Com 0 | stride 1 | 5 | 16550-compatible UART |
| 0x80300008 | Com 1 | stride 1 | 5 | 16550-compatible UART |
| 0x80300010 | Com 2 | stride 1 | 5 | 16550-compatible UART |
| 0x80300018 | Com 3 | stride 1 | 5 | 16550-compatible UART |
| 0x80300020 | Com 4 | stride 1 | 5 | 16550-compatible UART |
| 0x80300028 | Com 5 | stride 1 | 5 | 16550-compatible UART |
| 0x80300030 | Com 6 | stride 1 | 5 | 16550-compatible UART |
| 0x80300038 | Com 7 | stride 1 | 5 | 16550-compatible UART |
| 0x80f00000 | Timer | 64kB* | 6 | Write-only timer interval; see below |
| N/A | NMI | N/A | 7 |
Startup Overlay
On reset, ROM is overlaid on top of RAM at address 0x00000000. All reads from the lowest 512k addresses will be passed to ROM instead of RAM. Writes are passed through to RAM.
Writing 0 to the overlay register will disable the startup overlay. Attempting to write to the overlay port again should not be attempted.
IDE Controller
The IDE controller is little more than some buffers on the main bus, with a little glue logic for timing. Data bytes are swapped in hardware. This means byte commands can be sent to the interface unmodified, but 16-bit read/write data needs to be swapped in software.
Custom Interval Timer
The interval timer is a minimal custom design implemented using spare macrocells in the DRAM controller CPLD. Writing to the timer register will start the timer count. It will continue counting until it reaches 0, where it will hold until the count register is written to again. Timer interrupt request is asserted when the count reaches 1 and remains asserted until the count register is written to again. Writing 0 to the count register will disable the timer.
Since the timer is part of the DRAM control logic, it latches the least-significant 16 address bits as the count value. The value on the data bus is ignored.
The countdown runs at main bus frequency, 25MHz, so a count of 25,000 would be roughly a 1ms interval (plus interrupt servicing overhead). The maximum count is 65,535, which would be a little over 2.5ms.
Parts
43| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100nF | Wrap030_Video:C0805 | C1, C2, C3, C4, C5, C6, C7, C8, C9, C10, C11, C12, C14 |
| 7 | JP2E | Wrap030_Video:JP2 | JP1, JP2, JP3, JP4, JP5, JP6, JP7 |
| 6 | YC164-FR-071KL | Wrap030_Video:YC164-JR-0733RL | RN1, RN2, RN3, RN4, RN5, RN6 |
| 2 | MB84256PSK | Wrap030_Video:DIL28-3 | VRAM-HI0, VRAM-LO0 |
| 1 | 74137N | Wrap030_Video:DIL16 | IC7 |
| 1 | 74688N | Wrap030_Video:DIL20 | IC6 |
| 1 | ADA4891 | Wrap030_Video:SO14 | VBUF0 |
| 1 | ATF1508AS | Wrap030_Video:S84 | VID-GEN0 |
| 1 | CPOL-USE2-5 | Wrap030_Video:E2-5 | C13 |
| 1 | CPOL-USE3.5-8 | Wrap030_Video:E3,5-8 | C17 |
| 1 | JP10Q | Wrap030_Video:JP10Q | JP8 |
| 1 | JP4Q | Wrap030_Video:JP4Q | JP9 |
| 1 | L04P | Wrap030_Video:L04P | POWER0 |
| 1 | M10X2 | Wrap030_Video:2X10 | CTRL0 |
| 1 | M20X2SHROUDED | Wrap030_Video:2X20_SHROUDED | BUS0 |
| 1 | MA05-2 | Wrap030_Video:MA05-2 | VID0 |
| 1 | MC6821 | Wrap030_Video:DIL40 | PIA0 |
| 1 | XO-8 | Wrap030_Video:DIL08S | VCLK0 |
| 1 | YC164-FR-0775RL | Wrap030_Video:YC164-JR-0733RL | RN7 |
More from techav-homebrew/Wrap030
7- 4 layers106.7 × 83.8 mm

- 2 layers99.1 × 99.1 mm

- 2 layers99.1 × 99.1 mm

- 2 layers106.7 × 83.8 mm

- 2 layers106.7 × 99.1 mm

- 4 layers106.7 × 88.9 mm

- 2 layers106.7 × 83.8 mm

Similar boards
- 2 layers160.3 × 25.5 mm

N64rgb v3.prod
borti4938/n64rgb_flex
This repository contains all you need files to build your own DIY N64RGBv3 / N64RGBFlex board. Firmware is supplied in this repository, too.
60 parts24GPL-3.0 - 2 layers52.2 × 52.2 mm

Base
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards
43 parts3kApache-2.0 - 2 layers146.1 × 49.5 mm

Breakout 121pin 368255-2-Connector
rusefi/rusefi
rusefi - GPL internal combustion engine control unit
43 parts1.2k - 2 layers33 × 34 mm

- 2 layers96.1 × 78.6 mm

EYEBROW WARNING INDICATOR RIGHT
jrsteensen/OpenHornet
OpenHornet 1:1 F/A-18C Simulator Repository
43 parts431 - 2 layers42.9 × 19 mm

- 2 layers99.1 × 99.7 mm

RC6502 Prototyping
tebl/RC6502-Apple-1-Replica
An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!
43 parts193GPL-3.0 - 2 layers26.6 × 38.7 mm

Mdb slave esp32s3-mini
nodestark/mdb-esp32-cashless
ESP32-based MDB cashless device for vending machines, supporting EVA DTS DEX/DDCMP telemetry and payments over the MDB protocol via Bluetooth and MQTT
43 parts190MIT
Questions
How big is the Wrap030 Video PCB?
It measures 106.7 × 83.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Wrap030 Video use?
43 parts, built around the YC164-FR-071KL and YC164-FR-0775RL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Wrap030 Video KiCad files?
From the techav-homebrew/Wrap030 repository on GitHub, at the commit this page was made from: the board is ExpansionBoards/Video/Hardware/Wrap030_Video.kicad_pcb and its schematic ExpansionBoards/ATX-PSU_8b/ATX-PSU_8b.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Wrap030 Video design in my own project?
Its repository states no licence, so its author keeps all rights: ask techav-homebrew before reusing the design.