
Xmit
tdunning/xmit
A simple low-power digital transmitter for amateur bands using new components

A simple low-power digital transmitter for amateur bands using new components
Mixer test is an open-source printed circuit board by tdunning, from the tdunning/xmit repository on GitHub. It is a 4-layer board of 75 × 42 mm with 62 parts on 38 nets, routed with 99 tracks and 14 vias.
It is built around the 74LVC1G66GW, 74LVC2G157DCU and SN74CBT3253D. Its parts include 22 resistors, 18 capacitors, 8 ICs, 5 inductors and 4 connectors. It belongs with the audio and music boards of this library.
This repository has design files and (soon) code for a direct synthesis digital mode transmitter optimized for use on amateur bands. It should work well up to 2m. The novelty here relative to other systems like the QDX lies in a few areas:
a) the use of 74LVC2G157 to generate differential drive for a differential driver such as the THS6232 which can directly drive most balanced antennas without a balun at up to about 5W. This design avoids the need for fancy gate drive or paralleling FETs in favor of SMT packaging everywhere.
b) the use of SMT inductors and SMT analog switches such as the 74lvc2g53 or 74lvc1g66. This change is not earth-shattering, but it allows a much tighter all-SMT design with as much as 80dB suppression of harmonics. The high degree of suppression is achieved by using a filter tuned to put the response zeros directly on the harmonics and careful filter layout to suppress parasitic coupling.
The design of the transmit chain uses one of a number of filters to reject harmonics of the main frequency. One of these filters is selected using analog switches to suit the desire transmission frequency. These filters are designed to have minimal attenuation in each of several amateur bands. Since these bands are relatively narrow, passband flatness is not a grave concern. The zeros of the filters are positioned near the second or third harmonics of the carrier to suppress these frequencies very strongly. Higher harmonics have nearly 75dB of suppression.
The response curves for the filters designed so far are shown below.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 0R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15, R16, R20, R21, R30, R31 |
| 6 | 1µF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C12, C50, C51, C52, C53 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R44, R45, R46, R47 |
| 4 | 1nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C40, C41, C44, C45 |
| 4 | 33pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C20, C21, C30, C31 |
| 4 | ~ | MountingHole:MountingHole_2.2mm_M2 | H501, H502, H503, H504 |
| 3 | 100R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R10, R12 |
| 3 | 50R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3, R11 |
| 2 | 100nH | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L10, L11 |
| 2 | 10R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R42, R43 |
| 2 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R40, R41 |
| 2 | 220pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10, C11 |
| 2 | 330R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13, R14 |
| 2 | 4.7µH | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L40, L41 |
| 2 | 47pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C42, C43 |
| 2 | 74LVC1G66 | Package_TO_SOT_SMD:SOT-23-5 | U30, U31 |
| 2 | SMA | Connector_Coaxial:SMA_Samtec_SMA-J-P-H-ST-EM1_EdgeMount | J1, J10 |
| 1 | 1 µH | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L50 |
| 1 | 74LVC2G157 | Package_SO:VSSOP-8_2.3x2mm_P0.5mm | U1 |
| 1 | Conn_01x02_Pin | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-2_1x02_P2.54mm_Horizontal | J40 |
| 1 | LT5560 | Package_DFN_QFN:DFN-8-1EP_3x3mm_P0.5mm_EP1.66x2.38mm | U10 |
| 1 | OPA2356AIDR | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U40 |
| 1 | Output | TestPoint:TestPoint_2Pads_Pitch2.54mm_Drill0.8mm | TP40 |
| 1 | SN74CBT3253 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U20 |
| 1 | TPS7A2033PDBVRG4 | Package_TO_SOT_SMD:SOT-23-5 | U51 |
| 1 | TPS7A2042PDBVRG4 | Package_TO_SOT_SMD:SOT-23-5 | U50 |
| 1 | ~ | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-2_1x02_P2.54mm_Horizontal | J501 |

tdunning/xmit
A simple low-power digital transmitter for amateur bands using new components

tdunning/xmit
A simple low-power digital transmitter for amateur bands using new components

tdunning/xmit
A simple low-power digital transmitter for amateur bands using new components





stonedDiscord/Automatenplatinen
Reverse engineerte Hardware aus deutschen Spielautomaten.



LadyRoninEngineer/Si473x
Data Supporting development of Si473x series radios
It measures 75 × 42 mm and has 4 copper layers, 1.6 mm thick.
62 parts, built around the 74LVC1G66GW, 74LVC2G157DCU and SN74CBT3253D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the tdunning/xmit repository on GitHub, at the commit this page was made from: the board is mixer-test/mixer-test.kicad_pcb and its schematic mixer-test/mixer-test.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask tdunning before reusing the design.