
LevelShifter
gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

Self Balanced Inverted Pendulum
Self Balanced Inverted Pendulum is an open-source printed circuit board by tdestebe, from the tdestebe/Self_Balanced_Inverted_Pendulum repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 88 × 51.5 mm with 21 parts on 33 nets, routed with 5 tracks and 0 vias.
Its parts include 3 resistors, 2 connectors, 1 capacitor and 1 transistor.
Self Balanced Inverted Pendulum
This project aims to build an inverted pendulum stabilized by a single reaction wheel. The position of the pendulum is detected by a 3-axis analog gyroscope sensor (MPU6050 module). The position is analyzed inside an Arduino Nano that sends appropriate signals to a motor (Nidec 24H404H160).
The assembly of the CAD models and parts are designed with FreeCAD. Following worbenchs are used:
Part design to design 3D mechanical parts
Assembly 4.1 based on local axis systems
Fasteners for all screws and nuts
Mesh to create and export STL files
Inverted pendulum - FreeCAD mesh export
FreeCAD files are available at freeCad
STL 3D files are at STL_files
Simulation is performed through an openModelica implementation into the package SelfBalancedWheelPackage. Main Modelica model SingleWheelRobot calls model Dynamics in which PID, Motor, etc are implemented and calls model Animation to display rotation of 3D models of the reaction wheel and the arm.
Inverted pendulum - Modelica main model
| ||
|---|---|---|
| Inverted pendulum - Modelica Dynamics model |
| Inverted pendulum - Modelica Animation model |
Source files are available at Self Balaced Wheel Package
The source code for Arduino is provided at code. It is similar to the code written by Remigijus (see remrc - One-Axis-Reaction-Wheel-Stick).
The schema is also identical to the original one posted by Remigijus. I just rewrote it with Fritzing, including a breadboard and stored the source at circuit.
![]() |
| ![]() |
|---|---|---|
| Fritzing schema - Original |
| Fritzing schema - Breadboard |
In addition to Fritzing schema, I implemented KiCad schematic circuit and generated a KiCad PCB for visualisation into the 3D CAD assembly.
Kicad project is stored at kiCAD.
![]() |
| ![]() |
|---|---|---|
| KiCad circuit - Schema |
| KiCad circuit - PCD 3D view |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 2.6mm | Arduino_MountingHole:MountingHole_3.2mm | Hole, Hole, Hole, Hole |
| 4 | MountingHole_65mil | Arduino_MountingHole:MountingHole_65mil | MH1, MH2, MH3, MH4 |
| 2 | 3.6mm | Arduino_MountingHole:MountingHole_3.2mm | Hole, Hole |
| 1 | 100nF 35V | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 (100nF 35V) |
| 1 | 22 kOhm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 (22 kOhm) |
| 1 | 2N2222 | Package_TO_SOT_THT:TO-92L_Inline | Q1 (2N2222 - BC547) |
| 1 | 33 kOhm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 (33 kOhm) |
| 1 | 6.8 kOhm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 - 6.8 kOhm |
| 1 | Analog | Connector_PinHeader_2.54mm:PinHeader_1x15_P2.54mm_Vertical | J1 |
| 1 | Battery 500 mAh Lipo (11.1 V) | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | 500 mAh Lipo 11.1 V |
| 1 | Buzzer 5V | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 (Buzzer 5V) |
| 1 | Digital | Connector_PinHeader_2.54mm:PinHeader_1x15_P2.54mm_Vertical | J2 |
| 1 | ~ | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | MPU-6050 |
| 1 | ~ | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | Nidec_24H404H160 |

gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

mntmn/amiga2000-gfxcard
MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog


hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

drandyhaas/KiCadRoutingTools
A set of Python/Rust tools to aid routing in KiCad

Arrow-air/project-quiver
Project Quiver documentation, designs, and project artifacts.


It measures 88 × 51.5 mm and has 2 copper layers, 1.6 mm thick.
21 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the tdestebe/Self_Balanced_Inverted_Pendulum repository on GitHub, at the commit this page was made from: the board is kiCAD/kiCAD.kicad_pcb and its schematic kiCAD/Pendulum/Pendulum.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).