Skip to the content
2 layers46 × 15.7 mmAutoreset, the printed circuit board in 3D

FTDI cable adapter with dtrset reset method

Size
46 × 15.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
9
Pads
35
Tracks, vias
50, 3
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
17 May 2018
Updated
17 May 2018

Overview

Autoreset is an open-source printed circuit board by tadas-s, from the tadas-s/esp8266-autoreset repository on GitHub. It is a 2-layer board of 46 × 15.7 mm with 11 parts on 9 nets, routed with 50 tracks and 3 vias.

It is built around the BSS84. Its parts include 3 resistors, 3 transistors, 2 capacitors, 2 connectors and 1 switch.

Main components

1

README

README.md

FTDI cable adapter with dtrset reset method

Schematic taken from this blog post. The only small difference is output header pins drops CTS and RTS pins and replaces with FLASH and RESET signals.

So board input is a standard FTDI 6 pin cable and output is:

text
pin 1 -> GND
pin 2 -> FLASH (to be connected to GPIO0)
pin 3 -> VCC
pin 4 -> TXD
pin 5 -> RXD
pin 6 -> RESET (to be connected to reset pin)

Project mentioned above exposes FLASH and RESET as a separate 2 pin header.

Schematic preview:

schematic preview

Complete and tested board:

board

Schematic captured and PCB done using the amazing KiCad!.

Parts

11
QtyValueFootprintReferences
3100kResistors_SMD:R_0805_HandSolderingR1, R2, R3
2100nFCapacitors_SMD:C_0805_HandSolderingC1, C2
22N7002TO_SOT_Packages_SMD:SOT-23_HandsolderingQ2, Q3
1BSS84TO_SOT_Packages_SMD:SOT-23_HandsolderingQ1
1FTDI inPin_Headers:Pin_Header_Angled_1x06_Pitch2.54mmJ1
1Manual resetButtons_Switches_SMD:SW_SPST_PTS645SW1
1Programmer outPin_Headers:Pin_Header_Angled_1x06_Pitch2.54mmJ2

Similar boards

  • 2 layers33.7 × 97.8 mmHAN ESP TSS721, the printed circuit board in 3D

    HAN ESP TSS721

    UtilitechAS/amsreader-firmware

    ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

    29 parts470
  • 2 layers44.2 × 29.3 mmI2c tiny usb, the printed circuit board in 3D

    I2c tiny usb

    harbaum/I2C-Tiny-USB

    Cheap and simple I²C to USB interface

    27 parts454
  • 2 layers45 × 58.2 mmOpentama, the printed circuit board in 3D

    Opentama

    Sparkr-tech/opentama

    An open-source reference design for MCUGotchi

    65 parts237
  • 2 layers98.5 × 59.8 mmNeuron, the printed circuit board in 3D

    Neuron

    giant-axon/lu.i-neuron-pcb

    Lu.i is an electronic neuron circuit mimicking and illustrating the basic dynamics of real, biological neurons. The printed circuit board (PCB) features a configurable, fully analog implementation of the leaky…

    90 parts73CERN-OHL-S-2.0
  • 6 layers100 × 70 mmSa800u baseboard hw, the printed circuit board in 3D

    Sa800u baseboard hw

    antmicro/snapdragon-845-baseboard

    https://antmicro.com/blog/2022/04/open-source-snapdragon-845-baseboard/

    616 parts70Apache-2.0
  • 2 layers75 × 40 mmPicoTop Board Rev2, the printed circuit board in 3D

    PicoTop Board Rev2

    7west/PicoTop

    A very basic computer & OS based on the RP2350 microcontroller

    86 parts66
  • 4 layers50 × 59 mmKapula, the printed circuit board in 3D

    Kapula

    tejeez/geckokapula

    EFR32-based handheld transceiver

    166 parts65
  • 6 layers150 × 100 mmNV Meter rev b, the printed circuit board in 3D

    NV Meter rev b

    curtisseizert/Nanovoltmeter

    A low noise nanovoltmeter design files and code

    552 parts44

Questions

How big is the Autoreset PCB?

It measures 46 × 15.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Autoreset use?

11 parts, built around the BSS84. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Autoreset KiCad files?

From the tadas-s/esp8266-autoreset repository on GitHub, at the commit this page was made from: the board is autoreset.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Autoreset design in my own project?

Its repository states no licence, so its author keeps all rights: ask tadas-s before reusing the design.