Skip to the content
2 layers48.3 × 15 mmSensor v3, the printed circuit board in 3D

Yet Another (DIY) Hybrid Piano

Size
48.3 × 15 mm
Copper layers
2
Thickness
1.6 mm
Parts
5
Nets
8
Pads
20
Tracks, vias
33, 0
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
7 Jun 2024
Updated
20 Jan 2025

Overview

Sensor v3 is an open-source printed circuit board by szbergeron, from the szbergeron/yahp repository on GitHub. It is a 2-layer board of 48.3 × 15 mm with 5 parts on 8 nets, routed with 33 tracks and 0 vias.

Its parts include 4 ICs and 1 connector. It belongs with the sensors and measurement boards of this library.

README

README.md

WARN: Not ready for use yet

The boards are semi-final, but I need to finish part selection and push a new variant that allows varying sensor position. Code is in Proof-of-Concept state, and has a lot of stuff hard-coded that should be pulled out into configs.

#Because getting an AvantGrand would just be way too easy

Inspired by Greg Zweigle's DIY Hybrid Piano and the Cybrid Project.

I don't come from a hardware/EE background, so a lot of that stuff was done by feel rather than through meticulous science. Instead, I tried to all of the "magic" through software. The sensors are probably not "ideal", but they are cheap and dumb simple. I didn't use trimmers or anything like that to calibrate, opting instead to gather raw measurements and then apply software correction. I also opted to use onboard ADCs instead of external ones or any kind of extra voltage reference. This absolutely introduces some inaccuracy in the lower bits of the raw measurements, but again--software magic :)

The flip side of using such a simple design from an EE perspective is that fabrication is dumb simple, even if technically more expensive when looking at the BOM. Each key uses a single sensor, and there is an MCU for every 16 keys, plus some basic power filtering all on a PCB. I'm spectacularly bad at soldering, so this has as little of it as I could get away with. This project is aimed at being an easy "kit" to get components for and assemble. Follow along if you'd like!

Parts

5
QtyValueFootprintReferences
4DRV5055A1xLPGxQ1Package_TO_SOT_THT:TO-92_Inline_WideU1, U2, U3, U4
1Conn_02x04_Counter_Clockwisemine:Conn_02x04_2.54mm_pinJ1

More from szbergeron/yahp

3

Similar boards

  • 2 layers98 × 27 mmXy limit, the printed circuit board in 3D

    Xy limit

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    5 parts3.7k
  • 2 layers21 × 33 mm24g2usb pico2w, the printed circuit board in 3D

    24g2usb pico2w

    joypad-ai/joypad-os

    Universal controller firmware for building adapters, dongles, and custom controllers.

    5 parts1.7kApache-2.0
  • 2 layers53.2 × 59.6 mmA10 OLinuXino Lime Rev B SHIELD TEMPLATE, the printed circuit board in 3D

    A10 OLinuXino Lime Rev B SHIELD TEMPLATE

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    5 parts1.5k
  • 2 layers30 × 11 mmMain control board servo tester, the printed circuit board in 3D

    Main control board servo tester

    jamro/tiny-engineer

    A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

    5 parts1.1k
  • 2 layers78.8 × 35.3 mmKiCadTest, the printed circuit board in 3D

    KiCadTest

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    5 parts915
  • 2 layers50 × 23 mmMiniCircuits LTCC, the printed circuit board in 3D

    MiniCircuits LTCC

    VanceVagell/kv4p-ht

    Open source handheld ham radio project KV4P-HT

    5 parts828GPL-3.0
  • 2 layers20.3 × 15.2 mmL0 light sensor, the printed circuit board in 3D

    L0 light sensor

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    5 parts546MIT

Questions

How big is the Sensor v3 PCB?

It measures 48.3 × 15 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Sensor v3 use?

5 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Sensor v3 KiCad files?

From the szbergeron/yahp repository on GitHub, at the commit this page was made from: the board is boards_v3/sensor_v3.kicad_pcb and its schematic boards_v3/boards_v3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Sensor v3 design in my own project?

Its repository states no licence, so its author keeps all rights: ask szbergeron before reusing the design.