2 layers116.8 × 30 mm
Type d
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards
14 parts3kApache-2.0
2 layers
WaterpikDuino
synthetic65535/WaterpikDuino1Arduino based PCB for water flosser repair
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 14
- Nets
- 34
- Pads
- 69
- Tracks, vias
- 41, 0
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 16 Jul 2022
- Updated
- 16 Jul 2022
Overview
WaterpikDuino is an open-source printed circuit board by synthetic65535, from the synthetic65535/WaterpikDuino repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board with 14 parts on 34 nets, routed with 41 tracks and 0 vias.
Its parts include 6 resistors, 2 ICs, 2 transistors, 1 capacitor and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.
README
readme.mdWaterpikDuino
- Arduino based PCB for repair Waterpik water flosser: WP-660, WP-767, WP-672 (with two buttons and two LEDs on front panel).
- Functionality: 30+30 seconds timer, 5 minutes power-off timeout, 1/4 second massage pulses.
- IDE: KiCad
- Microcontroller fuses: Low:0xff High:0xc1 Extended:0xfd
Parts
14| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 1k | MyFootprints:RES | R1, R2, R3, R4, R5 |
| 1 | 100n | MyFootprints:CAP | C1 |
| 1 | 10k | MyFootprints:RES | R6 |
| 1 | 1n4007 | MyFootprints:DO-41 | D1 |
| 1 | ArduinoNanoCH340 | MyFootprints:ArduinoNanoCH340 | U1 |
| 1 | Conn_01x02 | Connectors_Terminal_Blocks:TerminalBlock_bornier-2_P5.08mm | J1 |
| 1 | Motor_DC | Connectors_Terminal_Blocks:TerminalBlock_bornier-2_P5.08mm | M1 |
| 1 | Q_NMOS_GDS_TO220 | TO_SOT_Packages_THT:TO-220-3_Horizontal | Q2 |
| 1 | Q_NMOS_GDS_TO252 | TO_SOT_Packages_SMD:TO-252-2 | Q1 |
| 1 | WaterpikFrontPanel | Pin_Headers:Pin_Header_Straight_1x08_Pitch2.54mm | U2 |
Questions
What parts does the WaterpikDuino use?
14 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the WaterpikDuino KiCad files?
From the synthetic65535/WaterpikDuino repository on GitHub, at the commit this page was made from: the board is hardware/WaterpikDuino.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the WaterpikDuino design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers32 × 22 mm
- 2 layers34 × 45 mm
2032Charger
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
14 parts915 - 2 layers34 × 109.9 mm
- 2 layers45.3 × 42.7 mm
- 2 layers42.5 × 28.8 mm
C5VRX JACK DIY
Twotoz/C5VRX
Ultra-minimal, zero-CPU 5.8 GHz analog FPV video receiver using ESP32-C5 Wi-Fi 6 PHY MODEM_DIAG, BitScrambler WBFM demodulation & resistor DAC CVBS
14 parts515GPL-3.0 - 2 layers54 × 47 mm
- 2 layers62 × 24 mm
