Skip to the content
2 layers92.5 × 50 mmSmd balanced, the printed circuit board in 3D

A small PCB that uses two LT6234CS8#TRPBF op amps to amplify a signal from a contact microphone.

Size
92.5 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
54
Nets
31
Pads
150
Tracks, vias
317, 33
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
2 Jul 2021
Updated
4 Aug 2021

Overview

Smd balanced is an open-source printed circuit board by Supermagnum, from the Supermagnum/balanced-smd repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 92.5 × 50 mm with 54 parts on 31 nets, routed with 317 tracks and 33 vias.

It is built around the LT6234CS8#PBF and SD06H0SB. Its parts include 25 resistors, 11 capacitors, 10 connectors, 5 diodes and 2 switches. It belongs with the audio and music boards of this library.

Main components

2

README

README.md

balanced-smd

A small PCB that uses two LT6234CS8#TRPBF op amps to amplify a signal from a contact microphone.

It has balanced output,input and should run on +48 phantom power. Shielded cable must with 3 leads be used for connection to the piezo crystals. Please use 0,5 W metal film resistors with 1% tolerance or better and audio quality capacitors. C0G (NP0) or X7R capacitors is very good.

It is important that the circuit board is mounted inside a metal box, and Ø2mm conducting metal standoffs are used. The corner pads of the PCB board is reserved for that. Of course the PCB board and components must not come in contact with any metal surface expect the standoffs.

The circuit may benefit from a Zobel network, that is a 680 pF capacitor and a 150 ohms resistor in series between pin 2 and 3 on the output or the input connector. It should avoid high frequency oscillation in the cable.

Schematic diagram: https://github.com/Supermagnum/balanced-smd/blob/main/smd-balanced.pdf

Component side picture with switch settings versus gain in dB: https://github.com/Supermagnum/balanced-smd/blob/main/front.jpg

Back side: https://github.com/Supermagnum/balanced-smd/blob/main/back.jpg

Aisler link: https://aisler.net/p/YIWINLSK Aisler can suply this assembled with the SMD components in place.

Parts

54
QtyValueFootprintReferences
10Conn_01x01_FemaleMountingHole:MountingHole_2.2mm_M2_ISO7380_PadJ1, J2, J3, J4, J6, J7, J8, J9, J10, J11
547uFCapacitor_SMD:C_0201_0603Metric_Pad0.64x0.40mm_HandSolderC4, C5, C6, C8, C9
41N4448WQ-7-F Diode_SMD:D_SOD-123D2, D3, D4, D5
3100Resistor_SMD:R_0603_1608MetricR1, R9, R12
210uFCapacitor_SMD:C_0201_0603Metric_Pad0.64x0.40mm_HandSolderC2, C7
21KResistor_SMD:R_0603_1608MetricR2, R19
21MResistor_SMD:R_0603_1608MetricR7, R11
22KResistor_SMD:R_0603_1608MetricR13, R20
23KResistor_SMD:R_0603_1608MetricR14, R21
24.7KResistor_SMD:R_0603_1608MetricR3, R4
2470Resistor_SMD:R_0603_1608MetricR5, R8
247pFCapacitor_SMD:C_0201_0603Metric_Pad0.64x0.40mm_HandSolderC10, C11
24KResistor_SMD:R_0603_1608MetricR15, R22
256KResistor_SMD:R_0603_1608MetricR6, R10
25KResistor_SMD:R_0603_1608MetricR16, R23
26KResistor_SMD:R_0805_2012MetricR17, R24
27KResistor_SMD:R_0805_2012MetricR18, R25
2SD06H0SB Teensy:SD07H1SBSW1, SW2
10.1uFCapacitor_SMD:C_0201_0603Metric_Pad0.64x0.40mm_HandSolderC1
133uFCapacitor_SMD:C_0201_0603Metric_Pad0.64x0.40mm_HandSolderC3
1LT6234CS8#PBFPackage_SO:SO-8_3.9x4.9mm_P1.27mmU1
1MMSZ11T1GDiode_SMD:D_SOD-123D1

Similar boards

  • 2 layers203 × 26.6 mmBlade13, the printed circuit board in 3D

    Blade13

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    54 parts3.7k
  • 2 layers30 × 50 mmModuleV421, the printed circuit board in 3D

    ModuleV421

    stuartpittaway/diyBMSv4

    Version 4 of the diyBMS

    54 parts1.1k
  • 2 layers100.1 × 40 mm32Bit shift register, the printed circuit board in 3D

    32Bit shift register

    MaltWhiskey/Mega-Cube

    16x16x16 PL9823 Cube with Teensy 4.0 and FlexIO driver

    54 parts766
  • 2 layers100 × 120 mmHubble lens, the printed circuit board in 3D

    Hubble lens

    wntrblm/Castor_and_Pollux

    A Juno-inspired dual oscillator

    54 parts587
  • 2 layersPassword, the printed circuit board in 3D

    Password

    limpkin/mooltipass

    Github repository dedicated to the mooltipass project

    54 parts531
  • 2 layers104.3 × 38.9 mmHYD ISO PANEL, the printed circuit board in 3D

    HYD ISO PANEL

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    54 parts431
  • 2 layers93.8 × 64.2 mmPiFinder smt, the printed circuit board in 3D

    PiFinder smt

    brickbots/PiFinder

    A plate solving telescope finder based around a Raspberry PI and RPI HQ Camera

    54 parts257GPL-3.0

Questions

How big is the Smd balanced PCB?

It measures 92.5 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Smd balanced use?

54 parts, built around the LT6234CS8#PBF and SD06H0SB. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Smd balanced KiCad files?

From the Supermagnum/balanced-smd repository on GitHub, at the commit this page was made from: the board is smd-balanced.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Smd balanced design in my own project?

Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).