
ArmLEDsPrototype
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

This is an envelope detector eurorack module. It is intended to take in eurorack signals or audio input and output the envelope.
Cv extractor is an open-source printed circuit board by stormyweathers, from the stormyweathers/cv-extractor repository on GitHub. It is a 2-layer board of 30 × 100 mm with 35 parts on 20 nets, routed with 245 tracks and 33 vias.
Its parts include 10 resistors, 7 capacitors, 3 connectors, 2 diodes and 1 IC.
This is an envelope detector eurorack module. It is intended to take in eurorack signals or audio input and output the envelope.
An input waveform passes through an adjustable gain noninverting amplifier, then an active rectifier, then finally a 2-pole sallen-key LPF with adjustable gain and cutoff.
* Buffered input/output
* Adjustable input/output gain
* Adjustable timescale of envelope detection* +12V: ?? mA
* -12V: ?? mA
* +5V: unused
* Width: 8HP The module works, but its not that great.
* Gain Pots are oriented reverse, unintuitive
* Turning the cutoff knob can cause it to oscillate
* The gain range is too large| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R5, R6, R7, R8, R9, R12 |
| 3 | 470nF | Capacitor_SMD:C_0603_1608Metric | C1, C5, C6 |
| 2 | 100uF | Capacitor_SMD:CP_Elec_6.3x7.7 | C7, C8 |
| 2 | 10k | matterwave:pot_bourns_PTV09 | RV2, RV3 |
| 2 | 1nF | Capacitor_SMD:C_0603_1608Metric | C9, C10 |
| 2 | D | Diode_SMD:D_SOD-323F | D1, D2 |
| 2 | Hole | MountingHole:MountingHole_3.2mm_M3 | H1, H2 |
| 2 | SolderJumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP2 |
| 1 | 100k | synth-components:dual-pot-P120 | RV1 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | RD1 |
| 1 | Abs | matterwave:TestPoint_TP107 | TP2 |
| 1 | CV Out | synth-components:mono-jack-thonk | J2 |
| 1 | GND | matterwave:TestPoint_TP107 | TP4 |
| 1 | Input | matterwave:TestPoint_TP107 | TP1 |
| 1 | Output | matterwave:TestPoint_TP107 | TP3 |
| 1 | TL074 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1 |
| 1 | Wave In | synth-components:mono-jack-thonk | J1 |
| 1 | power_connector_10pos | synth-components:power_connector_10pos | J3 |

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!


ozel/DIY_particle_detector
A mobile low-cost spectrometer for measuring radioactivity and the energy of ionising radiation like alpha particles and electrons

Seeed-Studio/OSHW-reCamera-Series
reCamera is a series of open-source AI cameras.




It measures 30 × 100 mm and has 2 copper layers, 1.6 mm thick.
35 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the stormyweathers/cv-extractor repository on GitHub, at the commit this page was made from: the board is cv-extractor.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask stormyweathers before reusing the design.