

WBA temperature monitor
This folder contains the hardware design for the WBA55THsensor board:
- Size
- 36 × 36 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 46
- Nets
- 42
- Pads
- 143
- Tracks, vias
- 279, 157
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 23 Mar 2026
- Updated
- 24 Mar 2026
Overview
WBA temperature monitor is an open-source printed circuit board by stm32-hotspot, from the stm32-hotspot/ST-wireless-services-workshop repository on GitHub. It is a 4-layer board of 36 × 36 mm with 46 parts on 42 nets, routed with 279 tracks and 157 vias.
Its parts include 22 capacitors, 4 resistors, 2 ICs, 2 inductors and 2 crystals. It belongs with the STM32 boards of this library.
README
WBA55_TH_sensor_HW/README.mdWBA55_TH_sensor – Hardware (KiCad)
This folder contains the hardware design for the WBA55_TH_sensor board:
- 4‑layer PCB
- Tuned 2.4 GHz antenna for STM32WBA55 wireless operation
- Designed in KiCad 9.0.0
- Based on STM32WBA55 MCU and SHT40AD1B temperature/humidity sensor
- Powered from CR2032 coin cell or external supply (see schematic)
The design can be used as a reference for integrating STM32WBA55 in low‑power BLE sensor applications.
Contents
- KiCad project:
*.kicad_pro*.kicad_sch(schematic)*.kicad_pcb(PCB layout)
- Generated documentation:
- Schematic and layout PDFs
- Gerber files
- BOM and component placement files
How to use
- Open the project in KiCad 9.0.0.
- Review the schematic and 4‑layer stack‑up, including the tuned RF antenna section.
- Adjust design parameters (components, layout, stack‑up) if needed for your application or PCB manufacturer.
- Generate manufacturing outputs (Gerbers, drill, pick‑and‑place) from KiCad for board fabrication.
Licensing
The hardware design files are provided under the terms described in the repository LICENSE file.
Third‑party components and trademarks (including but not limited to STM32WBA55 and SHT40AD1B) remain the property of their respective owners.
Parts
46| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C6, C7, C9, C12, C13, C14, C15 |
| 5 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | MCO, RX, SCL, SDA, TX |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | 1p2 | Capacitor_SMD:C_0402_1005Metric | C19, C20 |
| 2 | 6p | Capacitor_SMD:C_0402_1005Metric | C21, C22 |
| 2 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2 |
| 2 | Tooling Hole | MountingHole:ToolingHole_1.152mm | H3, H4 |
| 1 | 10n | Capacitor_SMD:C_0402_1005Metric | C16 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C8 |
| 1 | 10u | Capacitor_SMD:C_0402_1005Metric | C10 |
| 1 | 10u | Capacitor_SMD:C_0603_1608Metric | C18 |
| 1 | 2.2 uH | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | 3n3 | Inductor_SMD:L_0402_1005Metric | L2 |
| 1 | 4.7 uF | Capacitor_SMD:C_0402_1005Metric | C17 |
| 1 | 470n | Capacitor_SMD:C_0402_1005Metric | C11 |
| 1 | 47u | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | Antenna_Shield | koudelub:2.4GHz_centered | AE1 |
| 1 | Battery_Cell | Battery:BatteryHolder_Keystone_1060_1x2032 | BT1 |
| 1 | Conn_ARM_SWD_TagConnect_TC2030-NL | Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical | J1 |
| 1 | Crystal | Crystal:Crystal_SMD_2012-2Pin_TF2012 | Y1 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm_abracon | Y2 |
| 1 | LED_Dual_AKAK | koudelub:SML-522MUWT86_4P_RG_LED | D1 |
| 1 | SHT4x | Sensor_Humidity:Sensirion_DFN-4_1.5x1.5mm_P0.8mm_SHT4x_NoCentralPad | U1 |
| 1 | STM32WBA55CGUx | koudelub:UFQFPN-48_STM | U2 |
| 1 | SW_Push | koudelub:TS-1088-AR02016 | SW1 |
Similar boards
- 4 layers48 × 80 mm

- 4 layers50 × 42 mm

Beam Offset Switch
nanographs/Open-Beam-Interface
Just what you need to control the beam and get an image.
46 parts371 - 4 layers53.3 × 34.5 mm

- 4 layers91.1 × 53.6 mm

Parallel2usb
tomverbeure/fake_parallel_printer
Capture traffic on parallel printer port to USB
46 parts95BSD-2-Clause - 4 layers105 × 47 mm

Pdu
azonenberg/latentred
Open hardware 48x 1000baseT + 2x 25G SFP28 Ethernet switch
46 parts36BSD-3-Clause - 4 layers44.5 × 22.5 mm

- 4 layers41.8 × 14.8 mm

Nrf52811 usb
alvarop/chaac
This is a work in progress for a wireless weather station project.
46 parts21MIT - 4 layers50.8 × 114.3 mm

Questions
How big is the WBA temperature monitor PCB?
It measures 36 × 36 mm and has 4 copper layers, 1.6 mm thick.
What parts does the WBA temperature monitor use?
46 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the WBA temperature monitor KiCad files?
From the stm32-hotspot/ST-wireless-services-workshop repository on GitHub, at the commit this page was made from: the board is WBA55_TH_sensor_HW/WBA_temperature_monitor.kicad_pcb and its schematic WBA55_TH_sensor_HW/WBA_temperature_monitor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the WBA temperature monitor design in my own project?
Its repository states no licence, so its author keeps all rights: ask stm32-hotspot before reusing the design.