4 layers120.7 × 127 mm
4 layers67 × 57 mm
Tl2c ctrl
SteveMayze/TL2CTimed LED Lighting Control
- Size
- 67 × 57 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 58
- Nets
- 27
- Pads
- 139
- Tracks, vias
- 220, 23
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 10 Dec 2016
- Updated
- 10 Aug 2026
Overview
Tl2c ctrl is an open-source printed circuit board by SteveMayze, from the SteveMayze/TL2C repository on GitHub. It is a 4-layer board of 67 × 57 mm with 58 parts on 27 nets, routed with 220 tracks and 23 vias.
It is built around the ATTINY20-XU, LF120ABDT-TR and TPS70933DBV, with the IRLML2502, RJ45 and TL3315NF160Q among its other parts. Its parts include 15 resistors, 6 capacitors, 6 connectors, 4 diodes and 3 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
6
ATTINY20-XU
TSSOP-14-40℃~+85℃ 1.8V~5.5V 10bit 12 128Byte 12MHz 2KB 8 Bit AVR Built-in FLASH TSSOP-14 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontroller Units (MCUs/MPUs/SOCs)
LF120ABDT-TR
TO-252-2(DPAK)-40℃~+125℃@(Tj) 1 12V 16V 500mA Fixed Over Current Protection、Over Temperature Protection、Enable Positive TO-252-2(DPAK) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
TPS70933DBV
SOT-23-5-40℃~+125℃@(Tj) 1 1.4uA 150mA 190uVrms 3.3V 30V 80dB@(10Hz) 960mV@(150mA) Fixed Over Current Protection、Thermal shutdown、Enable control、Input under-voltage protection、Reverse-polarity current protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
IRLML2502
SOT-23-40℃~+150℃ 1 N-channel 1.25W 20V 4.2A 50mΩ@2.5V 600mV 66pF 740pF 8nC@10V SOT-23 MOSFETs ROHSGuangdong HottechMOSFETs
RJ45
TH-12PTH-12P SMT ROHSJLCPCB AssemblyUncategorised
TL3315NF160Q
SMD-4P,4.5x4.5mm-20℃~+70℃ 0.55mm 1.6N 12V 4.5mm 4.5mm 500,000 Cycles 50mA Gull Wing Round Button SPST Surface Mount,Vertical Without Bracket Yellow SMD-4P,4.5x4.5mm Tactile Switches ROHSE-SwitchTactile Switches
README
README.mdTL2C - Timed LED Lighting Control
Introduction
This project is a I2C device to control up to three High Power LED drivers using three PIR13 motion controllers.
The LED drivers in question are already provided on my site and are the SLV 464110 10W 3-36V (EAN: 4024163087155) constant current High Power LED drivers - as are the motion detectors PIR13 modules from ELV.
The device will be designed around the ATTINY20-SSU micro-controller. The requirements being SPI for In System Programming, I2C to connect to the master device and GPIO for the three High Power LED drivers and the three PIR13 sensors.
Parts
58| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 10kΩ | Resistors_SMD:R_0805 | R101, R307, R308, R309 |
| 4 | 660Ω | Resistors_SMD:R_0805_HandSoldering | R106, R107, R108, R204 |
| 3 | 1kΩ | Resistors_SMD:R_0805 | R301, R302, R303 |
| 3 | IRLML2502 | TO_SOT_Packages_SMD:SOT-23 | Q301, Q302, Q303 |
| 2 | 0Ω | Resistors_SMD:R_0805 | R103, R202 |
| 2 | 100n 50V | Capacitors_SMD:C_0805 | C101, C102 |
| 2 | NOPOP | Resistors_SMD:R_0805 | R104, R105 |
| 1 | 0.1μF 50V | Capacitors_SMD:C_0805 | C201 |
| 1 | 1μF 25V | Capacitors_SMD:C_0805 | C202 |
| 1 | 2.2μF 16V | Capacitors_SMD:C_0805 | C204 |
| 1 | 2.2μF 50V | Capacitors_SMD:C_0805 | C203 |
| 1 | 3V3DC | LEDs:LED_0805_HandSoldering | D202 |
| 1 | 5VDC | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | P109 |
| 1 | ATTINY20-X | Housings_SOIC:SOIC-14_3.9x8.7mm_Pitch1.27mm | IC101 |
| 1 | CTL CONN | Pin_Headers:Pin_Header_Straight_2x05_Pitch2.54mm | P103 |
| 1 | CTL PWR | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | P107 |
| 1 | LED_EG | LEDs:LED_0805_HandSoldering | D102 |
| 1 | LED_OG | LEDs:LED_0805_HandSoldering | D103 |
| 1 | LED_UG | LEDs:LED_0805_HandSoldering | D101 |
| 1 | LF120ABDT-TR | tl2c-footprint:LF120ABDT-TR | U201 |
| 1 | LOGO | tl2c-footprint:KiCad_LOGO_9mm | G*** |
| 1 | LOGO | tl2c-footprint:MyBasic_rounded_50_1 | G*** |
| 1 | Mode_Bridge | Pin_Headers:Pin_Header_Straight_1x03_Pitch2.54mm | P201 |
| 1 | RJ45 | tl2c-footprint:RJ45_8P8C | P102 |
| 1 | TL3315NF160Q | tl2c-footprint:TACTILE_FSM2JSMAA | SW101 |
| 1 | TPGND | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | TP101 |
| 1 | TPI Header | Connect:Tag-Connect_TC2030-IDC-NL | P104 |
| 1 | TPS70933 | tl2c-footprint:TPS70933DBVR | U202 |
The 41 most common of 58 parts.
Questions
How big is the Tl2c ctrl PCB?
It measures 67 × 57 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Tl2c ctrl use?
58 parts, built around the ATTINY20-XU, LF120ABDT-TR, TPS70933DBV and IRLML2502. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Tl2c ctrl KiCad files?
From the SteveMayze/TL2C repository on GitHub, at the commit this page was made from: the board is kicad/Hutschiene/tl2c_ctrl.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Tl2c ctrl design in my own project?
Its repository states no licence, so its author keeps all rights: ask SteveMayze before reusing the design.
More from SteveMayze/TL2C
8- 4 layers176 × 86.5 mm
- 4 layers120.7 × 127 mm
- 4 layers62.2 × 58.4 mm
- 2 layers67.5 × 102.7 mm
- 2 layers68 × 86.5 mm
- 2 layers82 × 58.4 mm
- 2 layers54.4 × 23.8 mm
Similar boards
- 2 layers76.2 × 17.8 mm
- 2 layers102 × 84 mm
3D PrEBo
TheColonelYoung/3D_PREBO
3D printer expansion board. Add more fan controllers, TMC2130 wiring support, induction probe voltage convertor, LED lighting (supports WS1812).
79 partsCC-BY-SA-4.0 - 4 layers90 × 50 mm
Greenmobi bms
G-Pereira/greenmobi-bms
A VESC compatible battery management system
141 parts31CERN-OHL-S-2.0 - 2 layers274.3 × 30.5 mm
Numitron2
74hc595/Numitron-Clock
An alarm clock using 9-segment numitron displays
56 parts6BSD-3-Clause - 4 layers77 × 127 mm
- 2 layers90 × 118 mm
Roverbase
stephendade/roverbase
A PCB design for Power and Motor control for small robots
61 parts3GPL-3.0 - 2 layers100 × 20 mm
- 2 layers15 × 10 mm
Magnetic switch
miket6000/SimpleSwitch
A magnetic power switch for use in rocketry
20 parts1CERN-OHL-W-2.0