Skip to the content
2 layersICL7660, the printed circuit board in 3D

A collection of widgets/adapters/breakouts to make prototyping easier

Copper layers
2
Thickness
1.6 mm
Parts
5
Nets
5
Pads
15
Tracks, vias
24, 0
Pours
2
Routed
Yes
KiCad
KiCad 3
Created
23 May 2015
Updated
12 Dec 2022

Overview

ICL7660 is an open-source printed circuit board by stefan-lochbrunner, from the stefan-lochbrunner/breadboard-widgets repository on GitHub. It is a 2-layer board with 5 parts on 5 nets, routed with 24 tracks and 0 vias.

It is built around the ICL7660SCBA. Its parts include 2 capacitors, 2 connectors and 1 IC. It belongs with the interfaces and adapters boards of this library.

Main components

1

README

README.md

A collection of widgets/adapters/breakouts to make prototyping easier. For more infos please see project page on HaD.io. A panel with a subset of these booards can also be ordered from the DirtyPCBs store

ATtiny prog board

Programming board suitable for ATtiny45/85 microcontrollers. Plugs into a breadboards power rails to minimize required space. USB version pin compatible with uUSB breakout. more info

Standard:

.sch.brd

With USB:

.sch.brd

DBx breakout

Simple breakout for DA-15, DB/DE-9 & DE-15(VGA) connectors. DB-9 to be placed on DA-15 footprint. more info

.brd .brd

ISP breakout

Simple ISP breakout. Order of pins corresponds to ATmega328 DIP so breakout can be plugged in next to it. Jumper wire required for RST. Also fits ATtiny45/85 with additional jumper for GND. more info

.sch.brd

v1.2

Added two additional pins to ISP & breadboard headers to allow this board to be used as breakout for e.g. ESP-01's.

.sch.brd

MOSFET breakout

DPAK MOSFET breakout to be used as single channel PWM driver. Footprint should also fit SOT-223 package where pin 2 is internally connected to tab. more info

.sch .brd

SMD LED breakout

Straight forward SMD LED breakout. See also revised button board that can be used as LED breakout

single
.sch
multi
.brd
SOIC/TSSOP-16 breakout & protoboard

Some variations on a SOIC-16 and TSSOP-16 breakout board.

.brd .brd .brd
USB breakouts
uUSB breakout

Main functionality is to provide "VUSB circuitry" for AVR microcontrollers. Can also be used as generic uUSB breakout by shorting 68R resistor footprints or as breadboard power supply (supplying 5V). more info

v1

.sch .brd

v2

Allows for supplying different voltages by populating the bottom side with desired regulator. For 5V short solder jumper.

superseded by v3

v3

Allows for supplying different voltages by populating the bottom side with desired regulator. The following modes are possible:

  • Supply rail and Vcc pin with 5V directly from USB (regulator not populated, short all 3 pads of solder jumper)
  • Supply regulator with 5V from USB which in turn supplies rail and Vcc pin (short center and top pad)
  • Supply regulator from rail and get regulated voltage on Vcc pin (short center and bottom pad)

.sch .brd

USB-B
.sch
Audio breakouts

Breakout boards for 3.5mm TRS & RCA jacks. more info

Based on @sufzoli 's https://github.com/sufzoli/suf-electronics-breadboard

.sch .sch

Combined both into single board to save PCB space.

.sch .sch

Button w/ pull resistor

more info

single button

Small board that incorporates a button and pull-resistor. Can be plugged into power rails. Depending on which side of a breadboard it is plugged in, acts as pull-up or pull-down. Optional footprints for low-pass filter for debouncing.

.sch .brd

single button with SMD LED breakout

added over complicated LED breakout to utilize board space. Also added arrow to indicate pull direction.

.sch .brd

Negative voltage converter

Included files of @sufzoli 's voltage inverter here and remade in Eagle for coherency. more info

Based on ICL7660, inverts supply voltage.

.sch .sch

Parts

5
QtyValueFootprintReferences
210uF/16VSM1206C1, C2
1ICL7660SSOIC-8U1
1OUTHDR-1J2
1PWRHDR-2J1

Similar boards

  • 2 layers70 × 100 mmKorg ms x, the printed circuit board in 3D

    Korg ms x

    jostsalathe/korg_ms-x

    An extreme MONOTRON mod by Soul Machine in form of an SMD PCB

    211 parts2
  • 2 layers98 × 27 mmXy limit, the printed circuit board in 3D

    Xy limit

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    5 parts3.7k
  • 2 layers21 × 33 mm24g2usb pico2w, the printed circuit board in 3D

    24g2usb pico2w

    joypad-ai/joypad-os

    Universal controller firmware for building adapters, dongles, and custom controllers.

    5 parts1.7kApache-2.0
  • 2 layers53.2 × 59.6 mmA10 OLinuXino Lime Rev B SHIELD TEMPLATE, the printed circuit board in 3D

    A10 OLinuXino Lime Rev B SHIELD TEMPLATE

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    5 parts1.5k
  • 2 layers30 × 11 mmMain control board servo tester, the printed circuit board in 3D

    Main control board servo tester

    jamro/tiny-engineer

    A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

    5 parts1.1k
  • 2 layers78.8 × 35.3 mmKiCadTest, the printed circuit board in 3D

    KiCadTest

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    5 parts915
  • 2 layers50 × 23 mmMiniCircuits LTCC, the printed circuit board in 3D

    MiniCircuits LTCC

    VanceVagell/kv4p-ht

    Open source handheld ham radio project KV4P-HT

    5 parts828GPL-3.0

Questions

What parts does the ICL7660 use?

5 parts, built around the ICL7660SCBA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ICL7660 KiCad files?

From the stefan-lochbrunner/breadboard-widgets repository on GitHub, at the commit this page was made from: the board is voltage inverter/KiCad (original)/ICL7660.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the ICL7660 design in my own project?

Its repository states no licence, so its author keeps all rights: ask stefan-lochbrunner before reusing the design.