Skip to the content
2 layers90.5 × 12 mmXEBookButtonBar, the printed circuit board in 3D

XEBook front panel button bar — volume for the PSU board, swap/Bluetooth/reset for the FujiNet (KiCad)

Size
90.5 × 12 mm
Copper layers
2
Thickness
1.6 mm
Parts
7
Nets
6
Pads
28
Tracks, vias
48, 1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
30 Jul 2026
Updated
16 Oct 2026

Overview

XEBookButtonBar is an open-source printed circuit board by sideburn, from the sideburn/xebook-buttonbar-kicad repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 90.5 × 12 mm with 7 parts on 6 nets, routed with 48 tracks and 1 via.

README

README.md

XEBook Button Bar

The front panel control strip for the XEBook Atari 8-bit laptop build: five tactile buttons on one panel-mount board.

Despite the repository name, this is not a FujiNet-only board. It serves two separate boards over two separate cables:

  • Volume (2 buttons) → VOL_BUTTS on the XEBook PSU board, driving the PAM8407 amplifier's up/down volume control
  • FujiNet (3 buttons) — swap, Bluetooth, reset → J_BTN1 on FN32ROV-XEBook-KiCad, which mounts the FujiNet FN32ROV WiFi/SIO adapter permanently inside the laptop

On the FujiNet main board those three buttons were moved off-PCB onto cable pigtails so they could be panel-mounted (see that project's CLAUDE.md, "External button bar interface (J_BTN1)"). This board is where they ended up, alongside the volume pair.

What's on it

  • VolDWN1 ("−") / VolUP1 ("+") — volume down / volume up, wired to vol1. Left-to-right on the board, VolDWN1 is the left button and VolUP1 the right.
  • swap1 / bt1 / rst1 — the three FujiNet control buttons (swap device, Bluetooth, reset), wired to fuji1.
  • All five are low-profile SMD tactile switches (E-Switch TL3342), active-low (each pulls its signal to GND when pressed).
  • vol1 — 4-pin PinHeader_1x04_P2.00mm_Vertical, through-hole. Pin 1 = volume up, pin 2 = GND, pin 3 = volume down, pin 4 = GND — matches the VOL_BUTTS connector on the XEBook PSU pin-for-pin.
  • fuji1 — 4-pin PinHeader_1x04_P2.00mm_Vertical, through-hole. Pin 1 = GND, pin 2 = swap, pin 3 = Bluetooth, pin 4 = reset — matches J_BTN1 on the main board pin-for-pin.

Cable wires are soldered directly to both connectors' pins rather than using a mating connector.

Revision note: both connectors widened from 3 pins to 4

fuji1 originally carried only the three FujiNet button signals with no dedicated ground pin — those buttons' return path only worked because it shared a ground reference with the volume cable. It is now a proper 4-pin header with its own GND pin, matching the main board's J_BTN1 so the two boards' cabling maps 1:1.

vol1 was a 3-pin header (GND / up / down), but the PSU's VOL_BUTTS connector it plugs into is a 4-pin JST-PH with two grounds interleaved between the two signals. vol1 is now 4-pin and matches VOL_BUTTS slot-for-slot, so that cable is a straight 1:1 harness too. Note that pins 1 and 2 swapped roles in the process, so an existing 3-wire volume cable cannot be reused on the new header.

See this repo's CLAUDE.md for the technical details of both fixes.

Status

Previously fabricated with 3-pin connectors (see production/). Both 4-pin fixes are designed, routed, and verified — kicad-cli sch erc and kicad-cli pcb drc --schematic-parity are clean (0 unconnected, 0 shorts, 0 parity issues) — and the JLCPCB fab package in Fab/ is up to date. Not yet re-fabricated.

Tooling

Built with KiCad 9. kicad-cli sch erc / kicad-cli pcb drc --schematic-parity are used to verify the design.

License

CERN Open Hardware Licence Version 2 - Strongly Reciprocal (CERN-OHL-S-2.0), matching the main board.

Parts

7
QtyValueFootprintReferences
5SW_PushButton_Switch_SMD:SW_SPST_TL3342bt1, rst1, swap1, VolDWN1, VolUP1
1fujiConnector_PinHeader_2.00mm:PinHeader_1x04_P2.00mm_Verticalfuji1
1volConnector_PinHeader_2.00mm:PinHeader_1x04_P2.00mm_Verticalvol1

Similar boards

  • 2 layersEncoder, the printed circuit board in 3D

    Encoder

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    7 parts4.3kMIT
  • 2 layers40 × 20 mmSensor smd, the printed circuit board in 3D

    Sensor smd

    scottbez1/splitflap

    DIY split-flap display

    7 parts4.2k
  • 2 layers19.8 × 30 mmZ limit, the printed circuit board in 3D

    Z limit

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    7 parts3.7k
  • 2 layers35.6 × 58.2 mmDisplay Carrier, the printed circuit board in 3D

    Display Carrier

    AxxAxx/AxxSolder

    STM32 Based soldering station for JBC cartridges, 9-24 VDC and USB-PD power

    7 parts1.7kGPL-3.0
  • 2 layers20.3 × 16.3 mmMap MPX, the printed circuit board in 3D

    Map MPX

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    7 parts1.2k
  • 2 layers26 × 44 mmCompact carrier board, the printed circuit board in 3D

    Compact carrier board

    jamro/tiny-engineer

    A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

    7 parts1.1k
  • 2 layers26.4 × 53.8 mmAtari pickup, the printed circuit board in 3D

    Atari pickup

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    7 parts1kGPL-3.0
  • 2 layersRj45 breakout, the printed circuit board in 3D

    Rj45 breakout

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    7 parts990GPL-3.0

Questions

How big is the XEBookButtonBar PCB?

It measures 90.5 × 12 mm and has 2 copper layers, 1.6 mm thick.

What parts does the XEBookButtonBar use?

7 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the XEBookButtonBar KiCad files?

From the sideburn/xebook-buttonbar-kicad repository on GitHub, at the commit this page was made from: the board is XEBookButtonBar.kicad_pcb and its schematic XEBookButtonBar.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the XEBookButtonBar design in my own project?

Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).