

Rbc circuits
If you're on a Mac, you might need to adjust the Docker permissions: This ensures Docker can run without requiring sudo every time.
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 140
- Nets
- 193
- Pads
- 537
- Tracks, vias
- 678, 466
- Pours
- 52
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 5 Jan 2023
- Updated
- 8 Aug 2024
Overview
Rbc circuits is an open-source printed circuit board by shiukaheng, from the shiukaheng/rbc repository on GitHub. It is a 4-layer board with 140 parts on 193 nets, routed with 678 tracks and 466 vias.
It is built around the ATMEGA2560-16AU, BTN70301EPAXUMA1 and LM2678SX-ADJ/NOPB, with the LT8609AEDDM#PBF and CSTCE16M0V53-R0 among its other parts. Its parts include 52 resistors, 33 capacitors, 13 ICs, 11 connectors and 10 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
5ATMEGA2560-16AU
TQFP-100(14x14)-40℃~+85℃ 10bit 16MHz 256KB 4.5V~5.5V 4KB 8 Bit 86 8KB AVR Built-in FLASH TQFP-100(14x14) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)BTN70301EPAXUMA1
TSDSO-14-40℃~+150℃ 12mΩ 17A 6V~18V Active High High Side Switch、Low Side Switch 过压保护、欠压锁定、集成电荷泵、Overcurrent Protection、Over temperature protection、锁存保护、Short-Circuit Protection TSDSO-14 Power Distribution Switches ROHSInfineon TechnologiesGate DriversLM2678SX-ADJ/NOPB
TO-263-7-40℃~+125℃@(TJ) 1 1.21V~37V 260kHz 4.2mA 5A 8V~40V Adjustable Buck Buck Built-in No TO-263-7 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersLT8609AEDDM#PBF
DFN-10-EP(3x3)-40℃~+125℃@(TJ) 1 1.7uA 200kHz~2.2MHz 3A 3V~42V 5V Buck Buck Built-in Fixed Yes DFN-10-EP(3x3) DC-DC Converters ROHSAnalog DevicesDC-DC ConvertersCSTCE16M0V53-R0
SMD3213-3P-20℃~+80℃ 15pF 16MHz 40Ω SMD3213-3P Ceramic Resonators ROHSMurataCeramic Resonators
README
README.md🤖 RoboCapture
A photogrammetry robot designed from scratch to autonomously scan indoor spaces.
🛠 Development
-
Cross-Platform: This repository is designed to be cross-platform, working on Windows, MacOS, and Linux. We leverage Docker and the devcontainer extension in VSCode to achieve this.
-
Testing: Most of the development and testing have been done on Linux. However, it might require slight adjustments when setting up on other operating systems.
🔧 Pre-requisites
$(hostname).localshould be broadcasted on the network using mDNS. This applies to both the robot and the development computer.- Docker must be running on a Linux environment.
🍎 MacOS Specifics
If you're on a Mac, you might need to adjust the Docker permissions:
sudo chown -R $(whoami) ~/.dockerThis ensures Docker can run without requiring sudo every time.
🖥️ X11 Authentication
For enabling X11 forwarding, execute the following command on the host computer:
xhost +local:docker📝 Notes
Please double-check the file permissions before making a commit to ensure they are appropriate, due to docker created files being owned by root. Fix shall be issued soon.
Parts
140| Qty | Value | Footprint | References |
|---|---|---|---|
| 24 | 4k7 | Resistor_SMD:R_1206_3216Metric | R26, R27, R28, R29, R32, R33, R34, R35, R36, R37, R38, R39, R40, R41, R42, R43 +8 |
| 13 | 100nF | Capacitor_SMD:C_0402_1005Metric | C5, C6, C13, C14, C19, C20, C21, C22, C23, C25, C30, C31, C33 |
| 6 | 300 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R15, R21, R22, R23, R24, R25 |
| 6 | BTN70301EPAXUMA1 | rbc Custom Library:Infineon_PG-TSDSO-14-22_custom | IC6, IC7, IC8, IC9, IC10, IC11 |
| 6 | LOGO | LOGO | G***, G***, G***, G***, G***, G*** |
| 4 | 100uF | SamacSys_Parts:16SVF180M | C10, C17, C18, C27 |
| 4 | 10nF | Capacitor_SMD:C_0805_2012Metric | C8, C15, C16, C26 |
| 4 | 1k | Resistor_SMD:R_0201_0603Metric | R2, R7, R8, R18 |
| 4 | 22uH | SamacSys_Parts:INDPM110100X400N | L2, L3, L4, L6 |
| 4 | 270uF | SamacSys_Parts:EEHZS1H221P | C2, C11, C12, C24 |
| 4 | 450mV 3A | Diode_SMD:D_SMA | D1, D2, D3, D5 |
| 4 | 8.87k | Resistor_SMD:R_0603_1608Metric | R4, R9, R10, R20 |
| 4 | Green | Diode_SMD:D_0805_2012Metric | D6, D7, D8, D9 |
| 4 | LM2678SX-ADJ/NOPB | rbc Custom Library:KTW0007B_custom | IC2, IC3, IC4, IC5 |
| 3 | 1k2 | Resistor_SMD:R_1206_3216Metric | R30, R31, R46 |
| 3 | 220nF | Capacitor_SMD:C_0805_2012Metric | C28, C29, C32 |
| 3 | Conn_01x06_Pin | Connector_Molex:Molex_Micro-Fit_3.0_43045-0612_2x03_P3.00mm_Vertical | J9, J10, J11 |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric | R11, R19 |
| 2 | 1M | Resistor_SMD:R_0402_1005Metric | R5, R12 |
| 2 | Extra 12V | Connector_Molex:Molex_Micro-Fit_3.0_43045-0412_2x02_P3.00mm_Vertical | J7, J8 |
| 1 | 100k | Resistor_SMD:R_0201_0603Metric | R6 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C4 |
| 1 | 10pF | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | 10uH | Inductor_SMD:L_0805_2012Metric | L5 |
| 1 | 18.2k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 187k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 18k ±5% | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R17 |
| 1 | 1k6 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 2.2uH | SamacSys_Parts:INDC4441X200N | L1 |
| 1 | 22uF | Capacitor_SMD:C_1206_3216Metric | C9 |
| 1 | 3k3 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R14 |
| 1 | 4.7uF | Capacitor_SMD:C_1206_3216Metric | C3 |
| 1 | 82k ±1% | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R16 |
| 1 | ATmega2560-16A | Package_QFP:TQFP-100_14x14mm_P0.5mm | U2 |
| 1 | CSTCE16M0V53-R0 | SamacSys_Parts:CSTCE16M0V53R0 | U1 |
| 1 | Conn_01x02_Pin | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | EN | Jumper:SolderJumper-3_P2.0mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | External Switch | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_Horizontal | J5 |
| 1 | Extra | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J2 |
| 1 | ICSP | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J3 |
| 1 | LED | Diode_SMD:D_0805_2012Metric | D4 |
| 1 | LOGO | decals:ugs | G*** |
| 1 | LT8609AEDDM#PBF | SamacSys_Parts:SON50P300X300X80-11N-D | IC1 |
| 1 | ON | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP3 |
| 1 | PROG | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J4 |
| 1 | RESET | SamacSys_Parts:FSM4JSMATR | S1 |
| 1 | Raspberry Pi Power/UART | Connector_Molex:Molex_Micro-Fit_3.0_43045-0612_2x03_P3.00mm_Vertical | J6 |
| 1 | Red | Diode_SMD:D_0805_2012Metric | D10 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
The 136 most common of 140 parts.
Similar boards
- 2 layers101.6 × 53.3 mm

- 2 layers101.6 × 53.3 mm

- 2 layers100 × 54 mm

- 4 layers55 × 55 mm

- 2 layers228.6 × 76.8 mm

Schwann Rev0.5b
The-Royal/The_Royal_Open-Source-Projects
A Master Repository For All things Royal Made
127 parts159MIT - 2 layers158 × 34 mm

- 2 layers43.4 × 43.4 mm

RGB LED TOY
madworm/RGB_LED_TOY
LAYOUT FILES: Led ring board with 8 RGB LEDs driven by an ATmega168-20AU TQFP-32 7x7 micro controller. KICAD and Gerber files.
34 parts5 - 2 layers

Questions
What parts does the Rbc circuits use?
140 parts, built around the ATMEGA2560-16AU, BTN70301EPAXUMA1, LM2678SX-ADJ/NOPB and LT8609AEDDM#PBF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rbc circuits KiCad files?
From the shiukaheng/rbc repository on GitHub, at the commit this page was made from: the board is circuits/rbc_circuits.kicad_pcb and its schematic circuits/MCU.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rbc circuits design in my own project?
Its repository states no licence, so its author keeps all rights: ask shiukaheng before reusing the design.