Skip to the content
2 layers15.1 × 16.2 mmLcd, the printed circuit board in 3D

Just odds and ends I've saved for a rainy day

Size
15.1 × 16.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
4
Nets
8
Pads
30
Tracks, vias
46, 10
Pours
2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
23 Oct 2022
Updated
1 Mar 2025

Overview

Lcd is an open-source printed circuit board by shades66, from the shades66/OddsAndEnds repository on GitHub. It is a 2-layer board of 15.1 × 16.2 mm with 4 parts on 8 nets, routed with 46 tracks and 10 vias.

Its parts include 2 resistors and 2 connectors. It belongs with the lEDs and displays boards of this library.

README

README.md

OddsAndEnds

Just odds and ends I've saved for a rainy day

markisol.h - ESPHome library to allow use of BOFU BF-301 controlled blinds via RF transmitter

Philips-LivingColours-GEN2.jpeg - PCB from an old Philips LivingColours lamp which we have long since lost the remote for. Modified to work as part of my ESPHome setup. See key on image for the locations of the various control pins, I mounted a M5Stack Pico over the location the original CPU sat and ran wires to the 4 gpios for RED/GREEN/BLUE & Enable (as far as I can tell enables the powersupply section that feeds the LED's). I did try using the 3v feed that fed the microprocessor but it was not enough for the ESP32 to powerup. instead I used a mini buck converter with the inputs from a capacitor connected to the Power in port (18 Volts!!) which provided a 5v feed for the pico.

LivingColours.yaml - ESPHome config for the above circuit. See pins defined for the connections I made on the PCB. This setup is the basic rgb light config with two extras for on_turn_on/on_turn_off which switch the enable pin high/low.

ESPHome/clockhacking - Hacking a cheap AliExpress clock to work via ESPHome.

Parts

4
QtyValueFootprintReferences
25.1kResistor_SMD:R_0805_2012MetricR12, R15
1Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ2
1USB_C_ReceptacleConnector_USB:USB_C_Receptacle_Palconn_UTC16-GJ1

More from shades66/OddsAndEnds

5
  • 2 layers46.6 × 32.7 mmEsp32-s3-dev, the printed circuit board in 3D

    Esp32-s3-dev

    shades66/OddsAndEnds

    Just odds and ends I've saved for a rainy day

    48 parts
  • 2 layers42.8 × 40.5 mmLcd, the printed circuit board in 3D

    Lcd

    shades66/OddsAndEnds

    Just odds and ends I've saved for a rainy day

    36 parts
  • 2 layers42.8 × 45.7 mmLcd, the printed circuit board in 3D

    Lcd

    shades66/OddsAndEnds

    Just odds and ends I've saved for a rainy day

    32 parts
  • 4 layers29.3 × 12.1 mmESP32PICOV3, the printed circuit board in 3D

    ESP32PICOV3

    shades66/OddsAndEnds

    Just odds and ends I've saved for a rainy day

    26 parts
  • 2 layers39.3 × 16.4 mmLcd, the printed circuit board in 3D

    Lcd

    shades66/OddsAndEnds

    Just odds and ends I've saved for a rainy day

    17 parts

Similar boards

  • 2 layers18.5 × 26 mm24g2usb rp2350zero, the printed circuit board in 3D

    24g2usb rp2350zero

    joypad-ai/joypad-os

    Universal controller firmware for building adapters, dongles, and custom controllers.

    4 parts1.7kApache-2.0
  • 2 layers116 × 33 mm966595-1 and 963356-1, the printed circuit board in 3D

    966595-1 and 963356-1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    4 parts1.2k
  • 2 layers19 × 18 mmDaughter board, the printed circuit board in 3D

    Daughter board

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    4 parts915
  • 2 layers24.8 × 24.8 mmNrf24 breakout, the printed circuit board in 3D

    Nrf24 breakout

    tardate/LittleArduinoProjects

    a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!

    4 parts803MIT
  • 2 layers26 × 20 mmCap chain, the printed circuit board in 3D

    Cap chain

    drandyhaas/KiCadRoutingTools

    A set of Python/Rust tools to aid routing in KiCad

    4 parts744MIT
  • 2 layers34.7 × 20 mmXG Station Power MSI, the printed circuit board in 3D

    XG Station Power MSI

    osy/XG_Mobile_Station

    Open source eGPU dock for ROG Ally and ROG Flow

    4 parts712CC-BY-4.0
  • 2 layers20.3 × 24.5 mmJack power input, the printed circuit board in 3D

    Jack power input

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    4 parts546MIT

Questions

How big is the Lcd PCB?

It measures 15.1 × 16.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Lcd use?

4 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Lcd KiCad files?

From the shades66/OddsAndEnds repository on GitHub, at the commit this page was made from: the board is ESP32Boards/USB-C-Board/lcd.kicad_pcb and its schematic ESP32Boards/ESP32-Pico-V2-MiniPICO/ESP32PICOV3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Lcd design in my own project?

Its repository states no licence, so its author keeps all rights: ask shades66 before reusing the design.