2 layers
2 layers
Init PPOc
serega3453/STM32_Init1- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 17
- Nets
- 40
- Pads
- 79
- Tracks, vias
- 84, 8
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 23 Oct 2025
- Updated
- 20 Apr 2026
Overview
Init PPOc is an open-source printed circuit board by serega3453, from the serega3453/STM32_Init repository on GitHub. It is a 2-layer board with 17 parts on 40 nets, routed with 84 tracks and 8 vias.
It is built around the MPU-6050 and AO3400A. Its parts include 6 resistors, 4 capacitors, 3 connectors, 2 ICs and 1 diode. It belongs with the STM32 boards of this library.
Main components
2
MPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometers
AO3400A
SOT-23-55℃~+150℃ 1 N-channel 1.45V 1.4W 30V 48mΩ@2.5V 5.7A 50pF 630pF 75pF 7nC@10V N-Channel SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
Parts
17| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R5, R6 |
| 2 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C5 |
| 2 | 4.7k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 1 | 10n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6 |
| 1 | 2.2n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 1 | AO3400A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Conn_01x02 | Connector_Wire:SolderWire-0.25sqmm_1x02_P4.5mm_D0.65mm_OD2mm | J1 |
| 1 | Contactor | Connector_Wire:SolderWire-0.25sqmm_1x02_P4.5mm_D0.65mm_OD2mm | J2 |
| 1 | FC | Connector_Wire:SolderWire-0.25sqmm_1x02_P4.5mm_D0.65mm_OD2mm | J3 |
| 1 | LED_RGB | LED_SMD:LED_RGB_5050-6 | D1 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U2 |
| 1 | STM32F070F6Px | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U1 |
More from serega3453/STM32_Init
1Similar boards
- 2 layers47.2 × 33.6 mm
Hackeriet imponator
hackeriet/imponator
The MCU has a 100nF capacitor between VCC and GND. This is quite standard for MCUs and sensors, but to be sure, check the datasheet.
45 parts2Apache-2.0 - 2 layers40 × 40 mm
Esp32Drone
HexaBitsEdu/ESP32-MiniDrone
this project is a drone based on esp32 microcontroller and coreless DC motor
83 parts2 - 2 layers30 × 20 mm
- 2 layers150 × 40 mm
- 2 layers43.6 × 43.6 mm
Esp32 dron
Sagaz0501/esp32-drone
PCB ESP32 quadcopter: KiCad hardware + Madgwick IMU firmware + WiFi web UI
75 parts1MIT - 4 layers19.8 × 21.9 mm
ESC
Adi1011-Data/ESP-Drone
A small brushed-motor ESC and flight-controller board for a drone built around a Seeed Studio XIAO ESP32-C3. The XIAO is the flight controller. An MPU6050 on the board supplies the accelerometer and gyroscope.
51 parts - 2 layers100 × 75 mm
AeroFC
angelowickramasinghe/Project-Drone
AeroFC-1S 1S brushed micro-quad flight controller (KiCad) — schematic, PCB, Gerbers, LCSC BOM
57 parts - 4 layers97.6 × 31.5 mm
Questions
What parts does the Init PPOc use?
17 parts, built around the MPU-6050 and AO3400A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Init PPOc KiCad files?
From the serega3453/STM32_Init repository on GitHub, at the commit this page was made from: the board is schematic/Simplified/Init_PPOc.kicad_pcb and its schematic schematic/Simplified/Init_PPO.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Init PPOc design in my own project?
Its repository states no licence, so its author keeps all rights: ask serega3453 before reusing the design.