Skip to the content
2 layers97 × 92 mmGRC22 ShutdownChargerBoardV1, the printed circuit board in 3D

GRC22 ShutdownChargerBoardV1

seandonker/GRC22_ChargerShutdownPCB1

Charger controller schematic and PCB files for FSAE GRC22 car

Size
97 × 92 mm
Copper layers
2
Thickness
1.6 mm
Parts
59
Nets
51
Pads
197
Tracks, vias
311, 20
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
27 Nov 2023
Updated
27 Nov 2023

Overview

GRC22 ShutdownChargerBoardV1 is an open-source printed circuit board by seandonker, from the seandonker/GRC22_ChargerShutdownPCB repository on GitHub. It is a 2-layer board of 97 × 92 mm with 59 parts on 51 nets, routed with 311 tracks and 20 vias.

It is built around the ALQ112. Its parts include 18 resistors, 11 connectors, 6 diodes, 4 capacitors and 4 ICs.

Main components

1

README

README.md

GRC22 Charging Shutdown Board for Guelph's FSAE Club

This board lies inside the external charging enclosure and is responsible for processing certain safety signals. It then determines if it is safe to activate the battery charger or not.

Schematic Theory
The board takes in three main safety signals: IMD Error, AMS Safety, and Charger Safety. IMD Error indicates the insulation in between the cells of the battery pack and the signal faults low when an error is detected. AMS Safety faults low as well when there is an issue with the voltage/temperature/current of any individual cell bank in the battery. Finally, charger safety sinks current when no error is present and is allowed to float when an error occurs. The latching logic is the core design challenge of this board. The FSAE rulebook has specific descriptions relating to the IMD and AMS signals as once an error is noticed, the output of the board must stay in the error state until manually reset (power cycled). This is why latches are required to save the error state. Two RS latches were implemented in combination with RC filters, AND gates, and inverters. This was done to combat unknown input signal conditions on startup. A full input/output-state circuit trace can be seen in the provided files (ShutdownBoard_Latching_Logic_States). The relay logic section acts as a chain of switches, so only if the charge sink, IMD, AMS, E-stop, and interconnect states are all correct, will then the charger and accessories be provided power.

Board Layout
The main requirement for the PCB layout was to be able to manufacture on a two layer PCB for cost reasons. The criteria for design were ease of assembly, connector and fuse access, and the visibility of the indicator LEDs and silkscreen.

schematic_view

3d_Viewer

PCB_Layout

Parts

59
QtyValueFootprintReferences
9470Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR1, R2, R3, R5, R6, R10, R12, R15, R19
4M4_HoleMountingHole:MountingHole_4.3mm_M4_DIN965_PadH1, H2, H3, H4
3DFootprints:SOD57-10D4, D5, D6
3LEDLED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolderD1, D2, D3
2.47nFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC3, C4
2100kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR11, R13
2100nFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC1, C2
210kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR17, R18
21KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR4, R16
22.2KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR22, R23
2ALQ112Footprints:RELAY_ALQ112K1, K2
2MC14043BDGFootprints:SOIC127P600X175-16NU2, U4
2PMOSFootprints:RSC002Q1, Q2
1120Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR14
1AMSTestPoint:TestPoint_Pad_D1.0mmTP2
1AMS LatTestPoint:TestPoint_Pad_D1.0mmTP4
1Brd Pwr LEDConnector_Molex:Molex_Micro-Fit_3.0_43650-0215_1x02_P3.00mm_VerticalJ9
1CAN InConnector_Molex:Molex_Micro-Fit_3.0_43650-0215_1x02_P3.00mm_VerticalJ7
1CAN OutConnector_Molex:Molex_Micro-Fit_3.0_43650-0215_1x02_P3.00mm_VerticalJ8
1Charger Active LEDConnector_Molex:Molex_Micro-Fit_3.0_43650-0215_1x02_P3.00mm_VerticalJ10
1Charger PwrConnector_Molex:Molex_Micro-Fit_3.0_43650-0215_1x02_P3.00mm_VerticalJ2
1Chrg SinkTestPoint:TestPoint_Pad_D1.0mmTP5
1E-StopConnector_Molex:Molex_Micro-Fit_3.0_43650-0215_1x02_P3.00mm_VerticalJ6
1Fault LEDConnector_Molex:Molex_Micro-Fit_3.0_43650-0215_1x02_P3.00mm_VerticalJ11
1FuseFootprints:FUSE_3557-2F2
1IMDTestPoint:TestPoint_Pad_D1.0mmTP1
1IMD LatTestPoint:TestPoint_Pad_D1.0mmTP3
1InterlockConnector_Molex:Molex_Micro-Fit_3.0_43650-0215_1x02_P3.00mm_VerticalJ5
1LOGOFootprints:GRCBannerG***
1LOGOGRC_Footprints:GRC_BannerG***
1MC14081BDGFootprints:SOIC127P600X175-14NU3
1MinitactorConnector_Molex:Molex_Micro-Fit_3.0_43650-0215_1x02_P3.00mm_VerticalJ4
1RelayConnector_Molex:Molex_Micro-Fit_3.0_43650-0215_1x02_P3.00mm_VerticalJ3
1Signal_InConnector_Molex:Molex_Micro-Fit_3.0_43045-0812_2x04_P3.00mm_VerticalJ1
1~Footprints:SOIC127P600X175-16NU1

Similar boards

  • 2 layers305.2 × 234.8 mmReflow, the printed circuit board in 3D

    Reflow

    mickdassive/reflowow-oven-controler

    firmware for a reflow controller

    117 parts2GPL-3.0
  • 2 layers216.9 × 86.8 mmSweepbling lp pcb, the printed circuit board in 3D

    Sweepbling lp pcb

    davidphilipbarr/Sweep

    Sweep - a small promicro based keyboard inspired by the Ferris.

    59 parts2.1k
  • 2 layers132.3 × 94.9 mmCheapino, the printed circuit board in 3D

    Cheapino

    tompi/cheapino

    An affordable split 36 keys keyboard

    59 parts1.2kCC-BY-4.0
  • 2 layers100 × 24 mmSTM32 Klipper Expander, the printed circuit board in 3D

    STM32 Klipper Expander

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    59 parts1.1kGPL-3.0
  • 2 layers77.5 × 20.4 mmTester, the printed circuit board in 3D

    Tester

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    59 parts915
  • 2 layers100 × 96 mmBacklight, the printed circuit board in 3D

    Backlight

    jackw01/scanlight

    A better light source for scanning color negative film

    59 parts397CERN-OHL-W-2.0
  • 2 layers95.3 × 100 mmBeyblock20, the printed circuit board in 3D

    Beyblock20

    ChrisChrisLoLo/beyblock20

    The magnetic, modular, 20-key macropad that can join together to form an ortholinear board

    59 parts335GPL-3.0

Questions

How big is the GRC22 ShutdownChargerBoardV1 PCB?

It measures 97 × 92 mm and has 2 copper layers, 1.6 mm thick.

What parts does the GRC22 ShutdownChargerBoardV1 use?

59 parts, built around the ALQ112. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the GRC22 ShutdownChargerBoardV1 KiCad files?

From the seandonker/GRC22_ChargerShutdownPCB repository on GitHub, at the commit this page was made from: the board is GRC22_ShutdownChargerBoardV1.kicad_pcb and its schematic GRC22_ShutdownChargerBoardV1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the GRC22 ShutdownChargerBoardV1 design in my own project?

Its repository states no licence, so its author keeps all rights: ask seandonker before reusing the design.