

free software/hardware mppt solar controller
- Size
- 136.1 × 70.6 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 152
- Nets
- 103
- Pads
- 541
- Tracks, vias
- 949, 117
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 29 Aug 2020
- Updated
- 9 Mar 2023
Overview
Mppt is an open-source printed circuit board by seandepagnier, from the seandepagnier/mppt repository on GitHub. It is a 4-layer board of 136.1 × 70.6 mm with 152 parts on 103 nets, routed with 949 tracks and 117 vias.
It is built around the ST485EBDR, ESP32-WROOM-32D and LM5109MA, with the AMS1117-5.0, LM393 and BCP56 among its other parts. Its parts include 50 resistors, 35 capacitors, 24 diodes, 14 transistors and 12 ICs. It belongs with the ESP32 boards of this library.
Main components
6ST485EBDR
SOIC-8-40℃~+85℃ 1 1 300uA 4.75V~5.25V 5Mbps Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHSSTMicroelectronicsRS-485 / RS-422 ICsESP32-WROOM-32D
-- WiFi Modules ROHSEspressif SystemsWiFi ModulesLM5109MA
SOIC-8-40℃~+125℃ 15ns 15ns 1A 1A 2 8V~14V Half-Bridge MOSFET SOIC-8 Gate Drivers ROHSTexas InstrumentsGate DriversAMS1117-5.0
SOT-223-40℃~+125℃ 1 1.3V 15V 1A 5V 60dB Fixed Positive Short Circuit Protection、Thermal shutdown SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLM393
SOP-8-16V~16V 0℃~+70℃ 2 2.5mA 250nA 2V~36V 36V 5mV 5nA Fail-safe function Open-drain SOP-8 Comparators ROHSMSKSEMIComparatorsBCP56
SOT-223-55℃~+150℃ 1 NPN 1.5W 100MHz 100nA 1A 250 500mV 5V 80V NPN SOT-223 Bipolar (BJT) ROHSHXY MOSFETBipolar (BJT)
README
READMEMPPT charge controller for maximum power
- free software and hardware design. Can be adapted to other requirements.
- all ceramic capacitors.
- buck/boost design allow either higher or lower voltage of battery vs panel.
- components rated for up to 48 volt system (60 volt mosfets)
- voltage and current monitoring on both input and output.
- high-efficiency regulators to power the 3.3v logic as well as the 10v needed for gate drive.
This project uses the stm32duino environment.
Parts
152| Qty | Value | Footprint | References |
|---|---|---|---|
| 17 | 10k | Resistor_SMD:R_0603_1608Metric | R2, R3, R5, R14, R16, R18, R21, R22, R28, R33, R37, R46, R47, R50, R51, R53 +1 |
| 12 | D | Diode_SMD:D_SOD-323F | D4, D7, D8, D9, D10, D11, D12, D13, D17, D18, D19, D20 |
| 8 | 1uF | Capacitor_SMD:C_1206_3216Metric | C8, C9, C15, C23, C24, C27, C28, C42 |
| 6 | 100nF | Capacitor_SMD:C_0805_2012Metric | C2, C6, C7, C13, C22, C32 |
| 6 | 33 | Resistor_SMD:R_0603_1608Metric | R15, R17, R26, R27, R39, R40 |
| 6 | Q_NMOS_GDS | mppt_footprints:TDSON-8-1 | Q3, Q4, Q10, Q11, Q12, Q13 |
| 5 | 100k | Resistor_SMD:R_0603_1608Metric | R13, R24, R30, R36, R38 |
| 5 | 10uF | Capacitor_SMD:C_1206_3216Metric | C14, C16, C17, C25, C45 |
| 4 | 10uF | Capacitor_SMD:C_0805_2012Metric | C4, C5, C12, C30 |
| 4 | 200k | Resistor_SMD:R_0603_1608Metric | R8, R9, R12, R23 |
| 4 | 4.7uF 100v | Capacitor_SMD:C_1210_3225Metric | C19, C20, C33, C34 |
| 4 | 5.6v | Diode_SMD:D_MiniMELF | D15, D24, D25, D27 |
| 4 | 510 | Resistor_SMD:R_0805_2012Metric | R10, R20, R25, R48 |
| 4 | Q_NPN_BEC | Package_TO_SOT_SMD:SOT-23 | Q5, Q6, Q8, Q14 |
| 3 | .001 | Resistor_SMD:R_1206_3216Metric | R11, R19, R31 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric | R7, R32, R34 |
| 3 | 333k | Resistor_SMD:R_0603_1608Metric | R45, R49, R52 |
| 3 | D | mppt_footprints:DO-214AC | D1, D2, D5 |
| 3 | D_Schottky_AAK | Package_TO_SOT_SMD:TO-277A | D6, D14, D16 |
| 3 | INA180 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U3, U6, U9 |
| 3 | lm5109 | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U4, U5, U8 |
| 2 | 10 | Resistor_SMD:R_0805_2012Metric | R29, R35 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric | C29, C31 |
| 2 | 4.7uF | Capacitor_SMD:C_1210_3225Metric | C3, C18 |
| 2 | 470uF | Capacitor_THT:CP_Radial_D16.0mm_P7.50mm | C11, C36 |
| 2 | FUSE | mppt_footprints:BladeFuse-CarType | F1, F2 |
| 2 | ST485EBDR | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U11, U12 |
| 2 | TVS | Diode_SMD:D_SMC | TVS1, TVS2 |
| 1 | 100uH | Inductor_THT:L_Toroid_Vertical_L33.0mm_W17.8mm_P12.70mm_Pulse_KM-5 | L3 |
| 1 | 100uH | Inductor_SMD:L_10.4x10.4_H4.8 | L1 |
| 1 | 120k | Resistor_SMD:R_0805_2012Metric | R4 |
| 1 | 20k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 33nF | Capacitor_SMD:C_0603_1608Metric | C10 |
| 1 | 33uF 100v | Capacitor_SMD:C_Elec_10x10.2 | C1 |
| 1 | 47k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-89-3 | U7 |
| 1 | APE1707H-33-HF | Package_TO_SOT_SMD:TO-252-5_TabPin3 | U2 |
| 1 | BCP56 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | Q9 |
| 1 | Conn_01x04 | mppt_footprints:rs422connector | J5 |
| 1 | ESP32-WROOM-32D | RF_Module:ESP32-WROOM-32 | U10 |
| 1 | GREEN | LED_SMD:LED_0805_2012Metric | D3 |
| 1 | IN+ | mppt_footprints:screw_terminal | J3 |
| 1 | IN- | mppt_footprints:screw_terminal | J6 |
| 1 | LM393 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Wuerth_693072010801 | J4 |
| 1 | OUT+ | mppt_footprints:screw_terminal | J7 |
| 1 | OUT- | mppt_footprints:screw_terminal | J8 |
| 1 | Q_NMOS_GDS | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Q_PMOS_GSD | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | Q_PNP_BCE | Package_TO_SOT_SMD:SOT-23 | Q7 |
| 1 | Thermistor_NTC | Resistor_SMD:R_0805_2012Metric | TH1 |
| 1 | UART | mppt_footprints:uart | J2 |
| 1 | YELLOW | LED_SMD:LED_0805_2012Metric | D26 |
| 1 | boot | mppt_footprints:SW_SPST_PTS810 | SW3 |
| 1 | menu | mppt_footprints:SW_SPST_PTS810 | SW2 |
| 1 | page | mppt_footprints:SW_SPST_PTS810 | SW1 |
Similar boards
- 4 layers60 × 60 mm

- 4 layers100 × 100 mm

MotorControllerPowerBoard
HEEV/motor-controller-2018
Sam Ellicott's and Isaac Jones's motor controller senior design project. Fall 2018-Spring 2019
134 parts4 - 2 layers100 × 100 mm

DC line module+Meter probe
kwiecinski/BMS-and-offgrid-photovoltaic-management-system
Project contains BMS for lead-acid batteries and ESP-based board used to pull information from EASUN offgrid inverter, energy meters and sensors.
100 parts3MIT - 2 layers30 × 54 mm

- 2 layers99.1 × 99.1 mm

- 2 layers290 × 221 mm

- 2 layers63.5 × 76.2 mm

- 2 layers105 × 70 mm

Questions
How big is the Mppt PCB?
It measures 136.1 × 70.6 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Mppt use?
152 parts, built around the ST485EBDR, ESP32-WROOM-32D, LM5109MA and AMS1117-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Mppt KiCad files?
From the seandepagnier/mppt repository on GitHub, at the commit this page was made from: the board is schematics/mppt.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Mppt design in my own project?
Its repository states no licence, so its author keeps all rights: ask seandepagnier before reusing the design.