

Experimental Kit
Analog Discovery 2(AD2)와 마이크로컨트롤러 보드를 함께 꽂아 실습하는 확장 보드의 KiCad 프로젝트입니다. Arduino UNO R3 호환 헤더, STM32 Nucleo Morpho 헤더(CN7/CN10), Adafruit Feather 소켓을 지원하며, 5V 주변장치(LCD, PWM)와 3.3V 주변장치(SPI)를 위한 레벨 시프터가 보드에 실장되어 있습니다.
- Size
- 69.7 × 76.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 42
- Nets
- 101
- Pads
- 273
- Tracks, vias
- 924, 184
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 15 Jul 2026
- Updated
- 5 Nov 2026
Overview
Experimental Kit is an open-source printed circuit board by sckim, from the sckim/Stm32NucleoF103RB repository on GitHub. It is a 2-layer board of 69.7 × 76.4 mm with 42 parts on 101 nets, routed with 924 tracks and 184 vias.
It is built around the ARDUINO UNO R3, TXU0304PW and 1N5819HW, with the BAT54S among its other parts. Its parts include 13 connectors, 12 resistors, 4 diodes, 4 transistors and 2 capacitors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
4ARDUINO UNO R3
Arduino UNO R3 Printed Circuit Board ModuleArduinoUncategorisedTXU0304PW
TSSOP-14-40℃~+125℃ 1 1.08V~5.5V 1.08V~5.5V 200Mbps 4 Level translator Power-off protection、Output enable high-impedance、Integrated pull-up resistor Tri-State Unidirectional TSSOP-14 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters1N5819HW
SOD-123-65℃~+150℃ 1 Independent 1A 1mA@40V 25A 40V 450mV@1A SOD-123 Schottky Diodes ROHSDiodes IncorporatedSchottky DiodesBAT54S
SOT-231 Pair Series Connection 1V@100mA 200mA 2uA@25V 30V 600mA SOT-23 Schottky Diodes ROHSMDDSchottky Diodes
README
Schematics/AD2_extension/README.md🔌 AD2 확장 키트 (Analog Discovery 2 Extension Kit)
Analog Discovery 2(AD2)와 마이크로컨트롤러 보드를 함께 꽂아 실습하는 확장 보드의 KiCad 프로젝트입니다. Arduino UNO R3 호환 헤더, STM32 Nucleo Morpho 헤더(CN7/CN10), Adafruit Feather 소켓을 지원하며, 5V 주변장치(LCD, PWM)와 3.3V 주변장치(SPI)를 위한 레벨 시프터가 보드에 실장되어 있습니다.
📂 파일 구성 (Files)
| 파일 | 내용 |
|---|---|
Experimental_Kit.kicad_pro | KiCad 프로젝트 파일 (이 파일을 여세요) |
Experimental_Kit.kicad_sch | 회로도 |
Experimental_Kit.kicad_pcb | PCB (2층, 배선 및 GND 동박 완료) |
AD2_extension.kicad_sym, sym-lib-table | 프로젝트 심볼 라이브러리 (TXU0304PW) |
AD2_extension.pretty/, fp-lib-table | 프로젝트 풋프린트 라이브러리 (UNO 실드 헤더, 2×19 미러 소켓) |
🧩 커넥터 (Connectors)
| 레퍼런스 | 이름 | 용도 |
|---|---|---|
| A1 | Arduino_UNO_R3 | Arduino UNO R3 호환 헤더 |
| J11 / J13 | CN7 / CN10 | STM32 Nucleo Morpho 헤더 |
| MS1 | Feather | Adafruit Feather 소켓 |
| J10 | AD2 | Analog Discovery 2 연결 |
| J2 | Keypad | 키패드 (전원 IOREF) |
| J3 | LCD | I2C LCD (5V, 레벨 시프트된 SDA/SCL) |
| J5 / J6 | PWM | 5V PWM 출력 (DIO3 / DIO5) |
| J14 | SPI | 3.3V SPI 장치 |
| J12 | IOREF | IOREF–3V3 연결 헤더 (아래 참고) |
| J7 / J9 | AREF / W1 | 아날로그 기준 전압 / AD2 파형 발생기 |
🔁 온보드 레벨 시프터 (On-board Level Shifters)
이전 버전은 BSS138 레벨 시프터 모듈을 헤더(J2/J4)에 꽂아 사용했으나, 현재는 보드에 직접 실장했습니다. 호스트 쪽 전압은 IOREF를 기준으로 하므로 5V 보드(UNO)와 3.3V 보드(Nucleo, Feather) 모두에서 규격에 맞는 신호 레벨이 나옵니다.
| 신호 | 회로 | 방향 |
|---|---|---|
| SDA, SCL → LCD | 2N7002 MOSFET (Q1, Q2), 호스트 쪽 풀업 4.7kΩ, 5V 쪽 풀업 10kΩ | 양방향 |
| DIO3, DIO5 → PWM | 2N7002 MOSFET (Q3, Q4), 풀업 10kΩ | IOREF → 5V |
| DIO13/11/10 → SCK/MOSI/CS | TXU0304 (U1), VCCA = IOREF, VCCB = 3.3V | 호스트 → 장치 |
| MISO ← DIO12 | TXU0304 (U1) | 장치 → 호스트 |
⚠️ Feather 사용 시: Feather에는 IOREF 핀이 없으므로 J12(IOREF)에 점퍼를 꽂아 IOREF를 3.3V에 연결해야 레벨 시프터가 동작합니다. UNO/Nucleo 사용 시에는 점퍼를 빼 두세요.
🛠️ 여는 방법 (How to Open)
- KiCad 최신 버전을 설치합니다.
Experimental_Kit.kicad_pro를 엽니다. 프로젝트 라이브러리(sym-lib-table,fp-lib-table)는 자동으로 로드됩니다.- 추가 라이브러리는 KiCad 라이브러리 저장소를 참고하세요.
Parts
42| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 4.7k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4, R5, R6, R7 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8, R9, R10, R11 |
| 4 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4 |
| 4 | MountingHole_3.2mm_M3 | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 2 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 2 | 1N5819HW | Diode_SMD:D_SOD-123 | D3, D4 |
| 2 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 2 | BAT54S | Package_TO_SOT_SMD:SOT-23 | D1, D2 |
| 2 | PWM | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7, J8 |
| 1 | 2.2k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13 |
| 1 | AD2 | AD2_extension:PinSocket_2x15_P2.54mm_Horizontal_BoardEdge | J10 |
| 1 | AREF | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | Arduino_UNO_R3 | AD2_extension:Arduino_UNO_R3_ShieldHeaders | A1 |
| 1 | CN10 | AD2_extension:PinSocket_2x19_P2.54mm_Vertical_Mirrored | J12 |
| 1 | CN7 | AD2_extension:PinSocket_2x19_P2.54mm_Vertical_Mirrored | J11 |
| 1 | FEATHERWING_NODIM | Adafruit nRF52 Bluefruit Feather rev G:FEATHERWING_NODIM | MS1 |
| 1 | I2C | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | Keypad | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | LCD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | SPI_3V3 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J6 |
| 1 | SPI_5V | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J13 |
| 1 | TXU0304PW | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U1 |
| 1 | W1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | W2 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
Similar boards
- 2 layers88.9 × 106 mm

- 2 layers88.9 × 101.6 mm

- 6 layers89 × 165 mm

- 6 layers200 × 190 mm

- 6 layers155.5 × 194.6 mm

NerdEKO Gamma NoATX
phil31/NerdEKO-Gamma
fork of the NerdOCTAXE-Gamma design (https://github.com/Patsch91/NerdOCTAXE-Gamma), with 12 x BM1370 (14TH/s SHA256)
499 parts42 - 4 layers155.5 × 130 mm

- 6 layers89 × 184 mm

NerdQX
IxTechCrypto/NerdQX
The NerdQX was developed as the world's first multi-ASIC home miner for overclocking, which also enables extremely efficient mining.
263 parts26CERN-OHL-S-2.0 - 6 layers91.8 × 139.8 mm

Questions
How big is the Experimental Kit PCB?
It measures 69.7 × 76.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Experimental Kit use?
42 parts, built around the ARDUINO UNO R3, TXU0304PW, 1N5819HW and BAT54S. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Experimental Kit KiCad files?
From the sckim/Stm32NucleoF103RB repository on GitHub, at the commit this page was made from: the board is Schematics/AD2_extension/Experimental_Kit.kicad_pcb and its schematic Schematics/AD2_extension/Experimental_Kit.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Experimental Kit design in my own project?
Its repository states no licence, so its author keeps all rights: ask sckim before reusing the design.