

Esc v3
My custom ESC project
- Size
- 40 × 25 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 37
- Nets
- 66
- Pads
- 221
- Tracks, vias
- 575, 48
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 4 Jan 2024
- Updated
- 4 Jan 2024
Overview
Esc v3 is an open-source printed circuit board by savob, from the savob/esc repository on GitHub, published under the CERN-OHL-W-2.0 licence. It is a 2-layer board of 40 × 25 mm with 37 parts on 66 nets, routed with 575 tracks and 48 vias.
It is built around the ATMEGA328PB-MU and FAN7888M. Its parts include 7 diodes, 6 transistors, 5 capacitors, 3 resistors and 3 connectors. It belongs with the robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATMEGA328PB-MU
QFN-32-EP(5x5)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 27 2KB 32KB 8 Bit AVR Built-in FLASH Power-on reset (POR)、Undervoltage detection (BOR/LVD/LVR/LVI)、Watchdog reset、External pin reset (NRST)、Built-in general-purpose timer、Programmable watchdog、Touch function QFN-32-EP(5x5) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)FAN7888M
SOIC-20-40℃~+125℃ 10V~20V 160uA 30ns 350mA 50ns 6 650mA IGBT、MOSFET Interleaved conduction protection、Dead-time control Three Phase SOIC-20 Gate Drivers ROHSonsemiGate Drivers
README
README.mdesc
My custom ESC attempt
Parts
37| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | Q_NMOS_SGD | esc:TPN2R903PLL1Q | Q1, Q2, Q3, Q4, Q5, Q6 |
| 5 | 0v8 | Diode_SMD:D_SOD-323 | D1, D2, D3, D6, D7 |
| 3 | 4u7 | Capacitor_SMD:C_0805_2012Metric | C2, C3, C4 |
| 2 | 100 | Resistor_SMD:R_Array_Convex_4x0402 | RN1, RN2 |
| 2 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C8 |
| 2 | 33k | Resistor_SMD:R_Array_Convex_4x0402 | RN4, RN5 |
| 2 | LED | LED_SMD:LED_0805_2012Metric | D4, D5 |
| 1 | 0 | Resistor_SMD:R_Array_Convex_4x0402 | RN3 |
| 1 | 10k | Resistor_SMD:R_Array_Convex_4x0402 | RN6 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 16MHz | Crystal:Resonator_SMD_muRata_CSTxExxV-3Pin_3.0x1.1mm | Y1 |
| 1 | 2k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 470 | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | A1 | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | A2 | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP2 |
| 1 | A3 | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP3 |
| 1 | ATmega328PB-MU | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U1 |
| 1 | AVR-ISP-6 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical_SMD | J1 |
| 1 | FAN7888 | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U2 |
| 1 | I2C_CTRL | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | REV | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP4 |
| 1 | SER_PROG | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J3 |
More from savob/esc
7- 2 layers65 × 35 mm

- 2 layers40 × 25 mm

- 2 layers40 × 25 mm

- 2 layers40 × 25 mm

- 2 layers49 × 34 mm

- 4 layers

- 2 layers12 × 13.5 mm

Similar boards
- 2 layers

Drone ESC
Arpit192005/Drone-ESC
A custom 3-phase Brushless DC (BLDC) Electronic Speed Controller (ESC) designed in KiCad, intended for drone and robotics applications.
31 parts1 - 2 layers75 × 75 mm

- 2 layers89.4 × 66.9 mm

E foc
embedded-pro/e-foc-hardware
hardware to be used with https://github.com/embedded-pro/e-foc
186 parts - 6 layers80 × 49 mm

ButterStick
butterstick-fpga/butterstick-hardware
Basic ECP5 based GigE to SYZYGY interface.
256 parts225 - 4 layers115 × 85.8 mm

- 4 layers50 × 50 mm

- 6 layers42.6 × 42.6 mm

Project OAK MAIN BRD V0
0101shift/Project_OAK
All design files, source code, and documentation for Project OAK, a digital watch inspired by mechanical complications.
145 parts29MIT - 4 layers115 × 65 mm

Questions
How big is the Esc v3 PCB?
It measures 40 × 25 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esc v3 use?
37 parts, built around the ATMEGA328PB-MU and FAN7888M. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esc v3 KiCad files?
From the savob/esc repository on GitHub, at the commit this page was made from: the board is hardware/esc_v3/esc_v3.kicad_pcb and its schematic hardware/driver_ic_adapter/driver_ic_adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esc v3 design in my own project?
Its repository publishes it under the CERN-OHL-W-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).