

BadgeInventor
- Size
- 81.6 × 61.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 37
- Nets
- 34
- Pads
- 125
- Tracks, vias
- 321, 16
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 12 Dec 2015
- Updated
- 20 Feb 2016
Overview
BadgeInventor is an open-source printed circuit board by sabas1080, from the sabas1080/InventorsBadge repository on GitHub. It is a 2-layer board of 81.6 × 61.3 mm with 37 parts on 34 nets, routed with 321 tracks and 16 vias.
It is built around the ESP-12E, MCP73831 and SPX1117M3, with the MBR120 and WS2812B among its other parts. Its parts include 12 resistors, 7 connectors, 6 diodes, 5 capacitors and 3 ICs. It belongs with the ESP8266 boards of this library.
Main components
5ESP-12E
SMD,24x16mm-20℃~+70℃ -90dBm 16dBm 170mA 2.4GHz 3V~3.6V 56mA 802.11b/g/n ESP8266 Chip On-board PCB Antenna Over-the-air (OTA) update UART、SPI、I2C SMD,24x16mm WiFi Modules ROHSAi-ThinkerWiFi ModulesMCP73831
UncategorisedMicrochip TechnologySPX1117M3
--40℃~+125℃@(Tj) 0.003%Vout 1 1.1V@(800mA) 1.25V~15V 5mA 75dB@(120Hz) 800mA Adjustable Over Current Protection、Over Temperature Protection Positive - Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSIPEXVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMBR120
SOD-123Schottky DiodesDoeshareWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
README.mdInventorsBadge
Parts
37| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10K | Resistors_SMD:R_0805_HandSoldering | R1, R4, R8, R9, R10 |
| 3 | 1K | Resistors_SMD:R_0805_HandSoldering | R2, R3, R7 |
| 2 | 10uF | Capacitors_SMD:C_0805_HandSoldering | C3, C4 |
| 2 | 1N4148 | Diodes_SMD:SOD-323 | D3, D5 |
| 2 | 3k3 | Resistors_SMD:R_0805_HandSoldering | R11, R12 |
| 2 | CONN_01X10 | Pin_Headers:Pin_Header_Straight_1x10 | P22, P23 |
| 1 | 1.0uF | Capacitors_SMD:C_0805_HandSoldering | C1 |
| 1 | 100K | Resistors_SMD:R_0805_HandSoldering | R6 |
| 1 | 220K | Resistors_SMD:R_0805_HandSoldering | R5 |
| 1 | 4.7uF | Capacitors_SMD:C_0805_HandSoldering | C2 |
| 1 | C | Capacitors_SMD:C_0805_HandSoldering | C5 |
| 1 | CONN_01X10 | Pin_Headers:Pin_Header_Straight_1x02 | P2 |
| 1 | ESP-12E | esp:ESP-12E | U3 |
| 1 | LED | LEDs:LED-0805 | D4 |
| 1 | LED | LEDs:LED-0603 | D1 |
| 1 | LOGO | theinventorhouse:electronic_cats_logo_8x6 | G*** |
| 1 | LOGO | theinventorhouse:intel_logo | G*** |
| 1 | LiPo | open-project:CONN_JST-2_SMD | P3 |
| 1 | MBR120 | Diodes_SMD:SOD-123 | D2 |
| 1 | MCP73831 | TO_SOT_Packages_SMD:SOT-23-5 | U2 |
| 1 | OLED_I2C | Socket_Strips:Socket_Strip_Straight_1x04 | P5 |
| 1 | PROG_JUMP | Pin_Headers:Pin_Header_Straight_1x02 | P1 |
| 1 | RESET | open-project:SW_PUSH_SMD | SW1 |
| 1 | SPX1117 | TO_SOT_Packages_SMD:SOT-223 | U1 |
| 1 | SW_PUSH | open-project:SW_PUSH_SMD | SW2 |
| 1 | USB Serial | Socket_Strips:Socket_Strip_Straight_1x06 | P6 |
| 1 | WS2812B | Neopix:WS2812B_PP | LED1 |
Similar boards
- 2 layers148.1 × 115.1 mm

- 4 layers45.5 × 66.7 mm

Sunshine pcb rounded
Nv7-GitHub/sunshine
The source code and PCB design for my melty brain combat robot, Sunshine!
54 parts1 - 2 layers84.5 × 80.3 mm

- 2 layers83.9 × 108.8 mm

- 2 layers45 × 60 mm

- 2 layers40 × 40 mm

VeinFinder ControlBoard
ElectronicCats/Vein-Finder
A reliable, easy-to-make and open source device!
39 parts7GPL-3.0 - 2 layers39.5 × 21.9 mm

- 2 layers61.2 × 61.2 mm

OpenBCI Wifi Shield
nestorufpe/OpentDCS-Hardware
All design files made with KiCad PCB design software. http://kicad-pcb.org/
35 parts1
Questions
How big is the BadgeInventor PCB?
It measures 81.6 × 61.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the BadgeInventor use?
37 parts, built around the ESP-12E, MCP73831, SPX1117M3 and MBR120. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BadgeInventor KiCad files?
From the sabas1080/InventorsBadge repository on GitHub, at the commit this page was made from: the board is badgeInventor.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the BadgeInventor design in my own project?
Its repository states no licence, so its author keeps all rights: ask sabas1080 before reusing the design.