Skip to the content
2 layers48 × 24.3 mmLS018B7DH02-breakout, the printed circuit board in 3D

LS018B7DH02-breakout

rroels/LS018B7DH02-breakout1

Small breakout board for the Sharp LS018B7DH02 display

Size
48 × 24.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
10
Nets
10
Pads
38
Tracks, vias
79, 8
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
16 Jun 2024
Updated
14 Aug 2024

Overview

LS018B7DH02-breakout is an open-source printed circuit board by rroels, from the rroels/LS018B7DH02-breakout repository on GitHub, published under the MIT licence. It is a 2-layer board of 48 × 24.3 mm with 10 parts on 10 nets, routed with 79 tracks and 8 vias.

Its parts include 6 connectors, 3 capacitors and 1 resistor. It belongs with the interfaces and adapters and lEDs and displays boards of this library.

README

README.md

Sharp LS018B7DH02 Memory LCD breakout board

[!WARNING] The information and material (code, designs, files, ...) are provided "AS IS". We make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability, or completeness of any information or material. Use this at your own risk.

Introduction

This repository contains a small breakout board for the Sharp LS018B7DH02 Memory LCD.

Also see this repository for an Arduino driver for this display: https://github.com/rroels/Sharp_LS018B7DH02_Arduino

Design Considerations

"Refresh" signal

To explain in layman's terms, this type of display needs a periodic "refresh signal" (even if you don't intend to change the displayed image), otherwise pixels start to get stuck (until the display is reset).

It's not actually a refresh of the display, but rather a "polarity inversion". A shortended explanation from the Sharp "Programming Sharp’s Memory LCDs" documentation:

When designing with a memory LCD panel, a decision must be made as to how VCOM will be generated. VCOM is an alternating signal that prevents a DC bias from being built up within the panel. If this DC bias is allowed to accumulate, it will eventually reach the point where the state of the liquid crystals in the panel cells cannot be changed by the panel electronics and the cells will no longer change state.

It must be supplied using one of two methods: software, or external clock. The mode is selected by the EXTMODE pin on the interface.

  • If external clock is selected [EXTMODE = H], the clock should be supplied on the EXTCOMM pin.
  • When the software clock is selected [EXTMODE = L], bit V of the command bit string sets the state of VCOM.

Depending on the chosen method, hardware is configured in one of two ways:

This breakout board should allow either hardware setup. This is done by setting a jumper that connects EXTMODE to either VSS or VDD. The user is still responsible for providing the refresh signal, either via software commands or via an external clock signal, depending on how the jumper is placed.

When the user chooses for the software clock option, EXTCOMIN should be tied to GND. This is also possible with a jumper.

VDD = VDDA

Typically, most designs combine digital power supply and analog power supply. This leaves the option to supply them seperately, but they can also be combined by placing a jumper. When the jumper is in placed, you only need to connect either VDD or VDDA.

SCS Pull-down

It's good practise to have a pull-up for SPI chip-select lines:

HOWEVER, note that the SCS is active high for this display, and not active low like most SPI devices. For this reason, we provide an optional pull-down resistor, instead of a pull-up resistor. This can be enabled by placing a jumper.

Schematics

We base ourselves on the following recommended circuits from the datasheet:

Which led to the following schematics:

Bill of Materials (BOM)

ReferenceFootprintValueQty
J6,J4,J5PinHeader_1x02_P2.54mm_VerticalConn_01x023
C1C_0603_1608Metric_Pad1.08x0.95mm_HandSolder0.1uF1
C3,C2C_0603_1608Metric_Pad1.08x0.95mm_HandSolder1uF2
J3PinHeader_1x03_P2.54mm_VerticalConn_01x031
J25034801000Conn_01x101
J1PinHeader_1x09_P2.54mm_HorizontalConn_01x091
R1R_0603_1608Metric_Pad0.98x0.95mm_HandSolder10K1

See image of the PCB below to have a better idea of what these components look like.

All capacitors and resistors and SMD 0603. Instead of the horizontal pin header I used, a vertical pin header will also work fine (as long as the pitch is 2.54mm).

How to Obtain the Physical PCB

The Gerber file is in this repository (gerber/LS018B7DH02-breakout.zip). Simply upload this file a PCB manufacturer of your choice (JLPCB, PCBWay, ...), and you they will make it for you for as low as $5 for 5 pieces (with the cheapest shipping option, which can take a few weeks).

[!WARNING] Note that you will still have to solder the components onto the PCB yourself!

How to Edit Design

Everything you need to edit this design in KiCad 8 is included in the repository.

However, this project uses symbols, footprints and 3D models from Component Search Engine. Their license allows us to do pretty much whatever we want with them, except redistributing them. For this reason I can't include them in this repository.

If you would like to edit the design yourself, you will need to download the following component libraries from https://componentsearchengine.com/ (it's free!):

From the downloaded zip file, move the content of the KiCad and 3D subfolders into the project structure, so that the end-result looks like this:

The KiCad project is configured to look for these files in these locations, using relative paths, so no changes to the project itself are required.

Related Sources

Parts

10
QtyValueFootprintReferences
3Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ4, J5, J6
21uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC2, C3
10.1uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC1
110KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR1
1Conn_01x03Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ3
1Conn_01x09Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_HorizontalJ1
1Conn_01x10503480-1000:5034801000J2

Similar boards

  • 2 layers57 × 55.2 mmLogicAnalyzer, the printed circuit board in 3D

    LogicAnalyzer

    gusmanb/logicanalyzer

    24 channel, 100Msps logic analyzer hardware and software

    10 parts5.1kGPL-3.0
  • 2 layers32.2 × 15.4 mmProtector, the printed circuit board in 3D

    Protector

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    10 parts4.3kMIT
  • 2 layers26 × 18 mmConn, the printed circuit board in 3D

    Conn

    yaqwsx/KiKit

    Automation tools for KiCAD

    10 parts2.1kMIT
  • 2 layers44.3 × 30.5 mmLime2-SATA RevA, the printed circuit board in 3D

    Lime2-SATA RevA

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    10 parts1.5k
  • 2 layers17.8 × 43.2 mmNano Adapter, the printed circuit board in 3D

    Nano Adapter

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    10 parts1.1kGPL-3.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    10 parts1kGPL-3.0

Questions

How big is the LS018B7DH02-breakout PCB?

It measures 48 × 24.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the LS018B7DH02-breakout use?

10 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the LS018B7DH02-breakout KiCad files?

From the rroels/LS018B7DH02-breakout repository on GitHub, at the commit this page was made from: the board is kicad/LS018B7DH02_breakout.kicad_pcb and its schematic kicad/LS018B7DH02_breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the LS018B7DH02-breakout design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).