

Dropkick
A data logger designed for skydivers
- Size
- 44.5 × 50.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 76
- Pads
- 249
- Tracks, vias
- 533, 57
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 22 Jan 2022
- Updated
- 27 Jan 2026
Overview
Dropkick is an open-source printed circuit board by rrainey, from the rrainey/dropkick repository on GitHub. It is a 2-layer board of 44.5 × 50.8 mm with 50 parts on 76 nets, routed with 533 tracks and 57 vias.
It is built around the SAM-M10Q-00B, BMP390 and MEM2061-01-188-00-A, with the ICM-42688-P, MCP73831T-2ACI/OT-HXY and LTST-S270KGKT among its other parts. Its parts include 14 capacitors, 12 resistors, 6 ICs, 4 connectors and 3 inductors. It belongs with the radio and wireless and sensors and measurement boards and the SAM D and SAM boards of this library.
Main components
12SAM-M10Q-00B
LGA-20Hot start acceleration LGA-20 GNSS Modules ROHSu-bloxGNSS ModulesBMP390
LGA-10(2x2)-40℃~+85℃ 0.6pa/K 1.5uA 1.65V~3.6V 30Kpa~1.25bar 3pa 50pa I2C、SPI Integrated ADC and digital interface、Standby mode、On-chip temperature output Yes LGA-10(2x2) Pressure Sensors ROHSBosch SensortecPressure SensorsMEM2061-01-188-00-A
MICR-SD-CARD1.88mm MicroSD Card (TF Card) Push-Push MICR-SD-CARD SD Card / Memory Card Connector ROHSGlobal Connector Technology (GCT)SD Card / Memory Card ConnectorICM-42688-P
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 16bit 2KB 7.5uA IMU (accelerometer + gyroscope) SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps Motion Event Detection, Synchronization, Timestamp Support LGA-14(2.5x3) Accelerometers ROHSTDK InvenSenseAccelerometersMCP73831T-2ACI/OT-HXY
SOT-23-5LBattery ManagementHXY MOSFETLTST-S270KGKT
SMD,1.6x1.2mm-30℃~+85℃ 130° 20mA 2V 571nm 574nm 71mcd 75mW Discrete Diode Side View Mount Water Clear Yellow Green SMD,1.6x1.2mm LED Indication - Discrete ROHSLite-OnLED Indication - Discrete3221-10-0300-00-TR
SMD,P=1.27mm-40℃~+105℃ 1.27mm 1.27mm 10P 1A 2 2x5P 5 5.3mm 50V 5mm Brass Gold Surface Mount,Vertical SMD,P=1.27mm IDC Connectors ROHSCNC TechWire To Board Connector1056TR
-- ROHSKeystone ElectronicsBatteryConnectorKMR211NGLFS
SMD-40℃~+85℃ 1.2N 1.9mm 2.8mm 32V 4.6mm 50mA Gull Wing Round Button SPST-NO Surface Mount,Vertical SMD Tactile Switches ROHSC&KTactile SwitchesLTST-C191KFKT
0603-30℃~+85℃ 130° 20mA 2V 605nm 611nm 75mW 90mcd Discrete Diode Orange Water Clear 0603 LED Indication - Discrete ROHSLite-OnLED Indication - DiscreteLTST-S270KRKT
SMD,1.6x1.2mm-30℃~+85℃ 130° 20mA 2V 54mcd 631nm 639nm 75mW Discrete Diode Red Side View Mount Water Clear SMD,1.6x1.2mm LED Indication - Discrete ROHSLite-OnLED Indication - DiscreteSM5817PL-TP
SOD-123FL-65℃~+125℃ 1 Independent 1A 20V 30A 450mV@1A SOD-123FL Schottky Diodes ROHSMicro Commercial ComponentsSchottky Diodes
README
README.mdDropkick
An experimental logger for skydivers
These devices are designed to be carried in a skydiver's breast pocket. The device loggs GPS position, barometric altitude, body rotation rates, and acceleration forces. Data is logged to a SD card for analysis on the ground.
There are two board variants active in this project: V4 SAM, is the board I use for skydiving. V5-CAM is a design repurposed for real-time use on a telescope pointing experiments. See CHANGELOG.md for a more detailed history.
Sponsorship
I'd like to thank PCBWay for their generous sponsorship. PCBWay supplied prototype PCBs and solder stencils for the CAM variant of this project. My experience with PCBWay predates their sponsorship here. PCBWay has been a great choice for my projects. They deliver good PCBs and accurate stencils quickly.
Description
This is a stand-alone, battery-powered data logger designed to be carried by a skydiver during their jump. It includes a GNSS (GPS) receiver, 6-DOF IMU, and altitude sensors. Data from all sensors is logged onto a Micro-SD card. The logged data can be reviewed post-jump by to-be-designed software.
One objective of this project is to research compact GNSS receiver performance in the dynamic environment that a skydiver routinely experiences. As such, there are currently two different u-blox receiver modules that I'm testing. There is a distinct PCB for each board variant.

Directory Structure
- pcb-sam - KiCad 6 PCB project files for the u-blox SAM-M10Q variant (this is the preferred variant for skydiving)
- pcb-cam - KiCad 7 PCB project files for the u-blox CAM-M8 variant
- enclosure - Fusion 360 enclosure; designed to be 3D-printed
- firmware - Arduino-based firmware for the microcontroller
- images - supporting images and videos
- analysis - GNU Octave-based log file analysis software
Gerber production files generated by KiCad are included in the PCB directories.
Exploded enclosure view (click to view)
Specifications
Enclosure Dimensions: 58mm x 51mm x 20mm
Power: rechargeable 500mAh Li-Polymer battery
Unit Weight: 55 grams
Storage: removable microSD card
Log file format: one log file for each jump; raw log format is an extension of NMEA0183.
USB micro-B connector (for recharging and programming)
Bootloader programmed via a 10-pin J-Link compatible connector; routine Arduino programming via the USB connector.
** Compiling Firmware The Arduino board type should be set to "Adafruit Trinket M0" with Tiny USB enabled.
These libraries are required:
- Adafruit_BMP3XX
- ICM42688
- SparkFun u-blox GNSS Arduino_Library
- MicroNMEA (2.0.6)
- SD (install the custom fork that I maintain on github)
PCB Notes
My prototype circuit boards were fabricated by both OSHPark and PCBgogo. Both are excellent manufacturers for hobbyists.
Bootloader
I flash all variants with the Adafruit Trinket M0 UF2 bootloader bin image. The current version is 3.15. Programming is performed via a Segger J-Link USB adapter using Microchip Studio (formerly Atmel Studio). Use Device = "ATSAMD21G18A". Program from the bootload .bin image file and then set the USER_WORD_0.NVMCTRL_BOOTPROT fuse to 8192 bytes.
Solder Reflow
The solder reflow process has turned out to be a tricky step in constructing the PCBs, particularly with the SAM-M8Q IC. Basically it requires extra heat soak in order to properly flow the solder. Some u-blox instructions are repeated below, but I'll ultimately add some notes about what worked best for me.
The u-blox Hardware Integration Manual provides some detailed requirements for soldering the GNSS module to a PCB:
Soldering paste
Use of "no clean" soldering paste is highly recommended, as it does not require cleaning after the soldering process has taken place. The paste in the example below meets these criteria.
- Soldering paste: OM338 SAC405 / Nr.143714 (Cookson Electronics)
- Alloy specification: Sn 95.5/ Ag 4/ Cu 0.5 (95.5% tin/ 4% silver/ 0.5% copper)
- Melting temperature: 217 °C
- Stencil thickness: 120 um
The final choice of the soldering paste depends on the approved manufacturing procedures. The paste-mask geometry for applying soldering paste should meet the recommendations.
Reflow soldering
A convection-type soldering oven is highly recommended over the infrared-type radiation oven. Convection-heated ovens allow precise control of the temperature, and all parts will heat up evenly, regardless of material properties, thickness of components and surface color. As a reference, see the "IPC-7530 Guidelines for temperature profiling for mass soldering (reflow and wave) processes”, published in 2001.
Preheat phase
During the initial heating of component leads and balls, residual humidity will be dried out. Note that this preheat phase will not replace prior baking procedures.
- Temperature rise rate: max. 3 °C/s. If the temperature rise is too rapid in the preheat phase it may cause excessive slumping.
- Time: 60 - 120 s. If the preheat is insufficient, rather large solder balls tend to generate. Conversely, if performed excessively, fine balls and large balls will be generated in clusters.
- End temperature: 150 - 200 °C. If the temperature is too low, non-melting tends to be caused in areas containing large heat capacity.
Heating and Reflow Phase
The temperature rises above the liquidus temperature of 217 °C. Avoid a sudden rise in temperature as the slump of the paste could become worse.
- Limit time above 217 °C liquidus temperature: 40 - 60s
- Peak reflow temperature: 245 °C
SAC405 solder paste is relatively expensive. I have been unable to locate SAC405 in hobbyist-friendly quantities, so I opted to use SAC305 for these prototypes. The melting qualities are quite similar, and it retains the essential "no clean" properties required by U-blox -- at the cost of potentially having slightly less sound solder connections.
I own a very basic infrared-type reflow oven, a Puhui T962. Even though infrared ovens are not recommended by U-blox, I decided to use it and pay careful attention to the programming of heating profile. First, I did a series to timing experiments with the standard profiles comparing them against the u-blox requirements. It turned out that my oven does not have a standard heating profile that would comply with these requirements. In particular, the closest standard profile held the oven temperature above 217 °C for roughly 90 seconds. That's far longer than the 40 to 60 seconds stated in the requirements. I had to develop a custom profile to match.
I programmed this profile into the reflow oven:
Enclosure Notes
The enclosure is designed to be 3D printed. Tolerances between the upper enclosure, lower enclosure, and the PCB are quite tight - printing precision will be important. Since 3D printing technologies will vary in their precision, you may need to scale or otherwise modify the objects to adequately match the final measurements in the original design.
For example, I printed the prototype enclosure on a MakerBot Replicator 2 (PLA) printer. Using the default print settings I know that an object will shrink typically by about 1% post-printing. I set the scale to 101% to compensate for that in the MakerBot Desktop tooling and the end result works well.
Credits
This PCB design is based on several Adafruit Feather and Stemma QT sensor boards. Adafruit maintains a family of excellent microcontroller and sensor evaluation boards and companion software. Support them. They deserve it.
The enclosure for this project was designed using the personal edition of Fusion 360. Autodesk supports the Maker community through access to this epic design tool. Try it out.
Disclaimer
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Parts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10uF | Capacitor_SMD:C_0805_2012Metric | C2, C3, C4, C5, C8 |
| 3 | 100K | Resistor_SMD:R_0603_1608Metric | R3, R4, R5 |
| 3 | 10K | Resistor_SMD:R_0603_1608Metric | R6, R11, R12 |
| 3 | 2.2K | Resistor_SMD:R_0603_1608Metric | R8, R9, R10 |
| 3 | MountingHole | lib_fr:MOUNTINGHOLE_2.5_PLATED | H1, H2, H3 |
| 2 | 100nF | Capacitor_SMD:C_0603_1608Metric | C12, C13 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C1, C9 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric | C6, C7 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | LTST-S270KGKT | lib_fr:CHIPLED_0603_NOOUTLINE | L1, L3 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C10 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C14 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | 3221-10-0300-00-TR | lib_fr:3221-10-0300-00-TR | J4 |
| 1 | 450405020524 | lib_fr:450405020524 | SW1 |
| 1 | ATSAMD21G18A-AUT | lib_fr:ATSAMD21G15B-AU | U4 |
| 1 | BATT | lib_fr:JSTPH2 | J2 |
| 1 | BMP390 | lib_fr:LGA10_BMP390_BOS | U5 |
| 1 | CR1220 | lib_fr:CR1220-2 | B1 |
| 1 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_Vertical | J3 |
| 1 | ICM-42688-P | lib_fr:PQFN50P300X250X97-14N | U6 |
| 1 | KMR211NG_LFS | lib_fr:KMR211NG LFS | SW2 |
| 1 | LTST-C191KFKT | lib_fr:CHIPLED_0603_NOOUTLINE | CHG1 |
| 1 | LTST-S270KRKT | lib_fr:CHIPLED_0603_NOOUTLINE | L2 |
| 1 | MCP73831T-2ACI/OT | lib_fr:SOT23-5 | U3 |
| 1 | MEM2061-01-188-00-A | lib_fr:MICROSD | X1 |
| 1 | OSHW-Logo2_14.6x12mm_SilkScreen | Symbol:OSHW-Logo2_14.6x12mm_SilkScreen | REF1 |
| 1 | OSHW-Logo2_7.3x6mm_SilkScreen | Symbol:OSHW-Logo2_7.3x6mm_SilkScreen | REF2 |
| 1 | SAM-M10Q | lib_fr:MODULE_SAM-M8Q-0-10 | U2 |
| 1 | SCHOTTKY 20V | Diode_SMD:D_SOD-123F | D1 |
| 1 | SPX3819-3.3 | lib_fr:SOT23-5 | U1 |
| 1 | USB C USB2.0 | Connector_USB:USB_C_Receptacle_GCT_USB4085 | J1 |
More from rrainey/dropkick
1- 2 layers44.5 × 50.8 mm

Similar boards
- 4 layers58.4 × 54 mm

- 2 layers71.5 × 33 mm

- 2 layers114 × 102 mm

Rpi cm4-switch board
sequoia-hope/rpi-cm4-switch-board
A Raspberry Pi (RPi) Compute Module 4 (CM4) Carrier Board with integrated gigabit switch
94 parts45 - 12 layers232 × 250 mm

KlusterLab r2.0
PCB-Arts/fast-open-switch-hardware
KlusterLab is an open FPGA development platform designed for experimenting with high-speed interfaces and formally verified IP cores.
1,169 parts15 - 2 layers81.8 × 55.4 mm

Cm4-digipi carrier
hemna/cm4-digipi-carrier
Raspberry Pi CM4 Carrier board for Ham radio PTT Control
52 parts3 - 2 layers34.5 × 50 mm

- 4 layers262.9 × 64.4 mm

MorphoDock
SlimeVR/SlimeVR-Morphocharger
SlimeVR Official charger design for butterfly trackers
188 parts1Apache-2.0 - 4 layers90 × 90 mm

Questions
How big is the Dropkick PCB?
It measures 44.5 × 50.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Dropkick use?
50 parts, built around the SAM-M10Q-00B, BMP390, MEM2061-01-188-00-A and ICM-42688-P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Dropkick KiCad files?
From the rrainey/dropkick repository on GitHub, at the commit this page was made from: the board is pcb-sam/dropkick.kicad_pcb and its schematic pcb-cam/dropkick.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Dropkick design in my own project?
Its repository states no licence, so its author keeps all rights: ask rrainey before reusing the design.
