

ESP32-DevKit Lipo Rev D
- Size
- 27.9 × 48.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 56
- Nets
- 65
- Pads
- 221
- Tracks, vias
- 1,221, 108
- Pours
- 12
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 8 Apr 2026
- Updated
- 11 Jun 2026
Overview
ESP32-DevKit Lipo Rev D is an open-source printed circuit board by rompasaurus, from the rompasaurus/dilder repository on GitHub. It is a 2-layer board of 27.9 × 48.3 mm with 56 parts on 65 nets, routed with 1,221 tracks and 108 vias.
It is built around the HX6211A332MR and WPM2015-3/TR. Its parts include 15 resistors, 7 capacitors, 6 diodes, 4 ICs and 2 transistors. It belongs with the power boards and the ESP32 boards of this library.
Main components
2HX6211A332MR
SOT-23-5-40℃~+85℃ 1 260mV@(200mA) 3.3V 500mA 50uVrms 55uA 60dB@(10KHz) 6V Fixed Positive Short Circuit Protection、Enable control SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSHXLinear Voltage Regulators (LDO)WPM2015-3/TR
SOT-231 P-Channel 1.1W 110mΩ@4.5V 1V 2.4A 20V 534pF 54pF 62pF 7.3nC@4.5V P-Channel ±8V SOT-23 MOSFETs ROHSKUUMOSFETs
README
hardware-design/reference-boards/rp2040-minimal-jlcpcb/README.mdRP2040 Minimal Design for JLCPCB
Based on Minimal design example referenced in Hardware design with RP2040: Using RP2040 microcontrollers to build boards and products. Design updated for KiCAD 7 and manufacture/assembly at JLCPCB.
Parts
56| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 1N5819S4/SOD123 | OLIMEX_Diodes-FP:SOD-123_1C-2A_KA | D1, D2, D4, D5, D6 |
| 4 | 10k/R0402 | OLIMEX_RLC-FP:R_0402_5MIL_DWS | R1, R6, R13, R17 |
| 4 | 2.2k/R0402 | OLIMEX_RLC-FP:R_0402_5MIL_DWS | R3, R4, R8, R9 |
| 3 | 470k/R0402 | OLIMEX_RLC-FP:R_0402_5MIL_DWS | R2, R5, R16 |
| 3 | Fiducial | OLIMEX_Other-FP:Fiducial1x3 | FID2, FID3, FID4 |
| 3 | Opened | OLIMEX_Jumpers-FP:SJ_1_SMALLER | BAT_PWR_E1, BAT_SENS_E1, PWR_SENS_E1 |
| 2 | 100nF/10V/10%/X7R/C0402 | OLIMEX_RLC-FP:C_0402_5MIL_DWS | C5, C9 |
| 2 | 22uF/6.3V/20%/X5R/C0603 | OLIMEX_RLC-FP:C_0603_5MIL_DWS | C1, C4 |
| 2 | 4.7uF/6.3V/C0603 | OLIMEX_RLC-FP:C_0603_5MIL_DWS | C6, C7 |
| 2 | BC817-40(SOT23) | OLIMEX_Transistors-FP:SOT23 | Q2, Q3 |
| 2 | HN1x19 | OLIMEX_Connectors-FP:HN1x19 | EXT1, EXT2 |
| 2 | TESTPAD | OLIMEX_Other-FP:TESTPAD_40-ROUND | D_Com1, GND1 |
| 1 | OLIMEX_LOGOs-FP:LOGO_OLIMEX_80 | Olimex_Logo_Small | |
| 1 | OLIMEX_LOGOs-FP:LOGO_RECYCLEBIN_1 | Sign_RecycleBin | |
| 1 | OLIMEX_LOGOs-FP:LOGO_OPENHARDWARE_8x8 | Logo_OSHW | |
| 1 | OLIMEX_LOGOs-FP:OLIMEX_LOGO_TB | Olimex_Logo_Big | |
| 1 | 1uF/10V/10%/X5R/C0603 | OLIMEX_RLC-FP:C_0603_5MIL_DWS | C8 |
| 1 | 220R/R0402 | OLIMEX_RLC-FP:R_0402_5MIL_DWS | R10 |
| 1 | 220k/R0402 | OLIMEX_RLC-FP:R_0402_5MIL_DWS | R15 |
| 1 | 4.7k/R0402 | OLIMEX_RLC-FP:R_0402_5MIL_DWS | R11 |
| 1 | BAT54C(SOT23-3) | OLIMEX_Diodes-FP:SOT23-3 | D3 |
| 1 | BL4054B-42TPRN(SOT23-5) | OLIMEX_IC-FP:SOT-23-5 | U1 |
| 1 | CE_Sign_Small | OLIMEX_Signs-FP:CE_Sign_Small | Sign_CE_Small |
| 1 | CH340X(MSOP-10) | OLIMEX_IC-FP:MSOP-10_Pitch-0.5mm_3.00x3.00x1.00mm | U2 |
| 1 | DW02S | OLIMEX_Connectors-FP:LIPO_BAT_VERTICAL_DW02S | BAT1 |
| 1 | ESP32-WROOM-32D-4MB | OLIMEX_Cases-FP:ESP32-WROVER_MODULE | U5 |
| 1 | Fiducial | OLIMEX_Other-FP:Fiducial1x3_Past | FID1 |
| 1 | HX6211A332MR | OLIMEX_Regulators-FP:SOT-23-5 | U3 |
| 1 | IT-1185AU2-160G-G-TR | OLIMEX_Buttons-FP:IT1185AU2_V2 | RST1 |
| 1 | LED/YELLOW/0603 | OLIMEX_LEDs-FP:LED_0603_KA | CHARGING1 |
| 1 | MISB-SWMM-5B-LF(USB_MICRO) | OLIMEX_Connectors-FP:USB-MICRO_MISB-SWMM-5B_LF | USB-UART1 |
| 1 | NA/R0402 | OLIMEX_RLC-FP:R_0402_5MIL_DWS | R7 |
| 1 | Val** | OLIMEX_LOGOs-FP:LOGO_ANTISTATIC_SMALL_4.5mmX2.8mm | Sign_Antistatic |
| 1 | WPM2015-3/TR | OLIMEX_Transistors-FP:SOT23 | FET1 |
More from rompasaurus/dilder
3- 2 layers34.8 × 65.9 mm

- 2 layers52 × 51 mm

- 2 layers19.6 × 19.6 mm

Similar boards
- 4 layers25.4 × 53.3 mm

RT1010Py Rev.C
OLIMEX/RT1010Py
RT1010Py is Cortex-M7 running at 500Mhz MicroPython board
89 parts6GPL-3.0 - 4 layers28 × 80 mm

ESP32-PoE Rev M
OLIMEX/ESP32-POE
ESP32 IoT development board with 100Mb Ethernet and 802.3 Power Over Ethernet (POE)
142 parts415Apache-2.0 - 2 layers50.8 × 62.2 mm

ESP32-GATEWAY Rev I
OLIMEX/ESP32-GATEWAY
ESP32 IoT Gateway board with BLE WIFI and Ethernet
111 parts322Apache-2.0 - 2 layers75.2 × 74.7 mm

ESP32-EVB Rev K2
OLIMEX/ESP32-EVB
ESP32 WiFi / BLE Development board with Ethernet interface, Relays, microSD card
170 parts287Apache-2.0 - 2 layers50 × 86 mm

MOD LCD2.8RTP Rev D
OLIMEX/MOD-LCD2.8RTP
TFT COLOR LCD module with UEXT connector for ESP32-EVB
44 parts10Apache-2.0 - 2 layers

- 2 layers79 × 79 mm

Hm env sensor
HiMinds/himinds-boosting-innovation-embedded-env-sensor-hw
HiMinds Open Source Wireless Environmental Sensor HW
94 parts1Apache-2.0 - 2 layers27.9 × 55.9 mm

ESP32-S3-DevKit LiPo Rev B
Shaas1405/CASTOR
Natural disasters can rapidly disable communication infrastructure, leaving affected communities and emergency responders unable to exchange critical information when every minute matters, so CASTOR is a portable…
64 parts1
Questions
How big is the ESP32-DevKit Lipo Rev D PCB?
It measures 27.9 × 48.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP32-DevKit Lipo Rev D use?
56 parts, built around the HX6211A332MR and WPM2015-3/TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32-DevKit Lipo Rev D KiCad files?
From the rompasaurus/dilder repository on GitHub, at the commit this page was made from: the board is hardware-design/examples/05-olimex-devkit-lipo/HARDWARE/ESP32-DevKit-LiPo-Rev.D/ESP32-DevKit-Lipo_Rev_D.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32-DevKit Lipo Rev D design in my own project?
Its repository states no licence, so its author keeps all rights: ask rompasaurus before reusing the design.