Skip to the content
4 layers51 × 47.5 mmSelector, the printed circuit board in 3D
Size
51 × 47.5 mm
Copper layers
4
Thickness
1.6 mm
Parts
18
Nets
16
Pads
48
Tracks, vias
38, 1
Pours
25
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
26 Mar 2024
Updated
3 Nov 2026

Overview

Selector is an open-source printed circuit board by robotique-udes, from the robotique-udes/PCB repository on GitHub, published under the MIT licence. It is a 4-layer board of 51 × 47.5 mm with 18 parts on 16 nets, routed with 38 tracks and 1 via.

It is built around the XT60PW-M and BZV55B5V6. Its parts include 5 resistors, 5 connectors, 3 diodes, 1 IC and 1 fuse.

Main components

2

README

rover/2024/pdb/README.md

PDB (Power Distribution Board)

PCB servant à gérer la distribution à bas courant et le de data du rover

Image du PCB en 3D

Capture d’écran, le 2024-09-18 à 21 24 36

Objectifs:

  • Protéger tous les autres boards du Over/Under Voltage pour le 5V, 12V et 24V
    • Seulement le 5v et le 24v sont protégé, car les résistance 5% ont trop d'incertitude.
  • Injecteur POE(12V custom pinout) pour les cameras branché en Ethernet
    • On/Off possible par le MCU
  • Diriger le signal des cameras sur les bonnes pins selon la norme Ethernet
  • Agir en tant que POE pour les antennes 24V (vrai POE)
  • Controller l'alimentation de 2 circuit d'accessoires 12V
    • Par 2 connecteurs Ethernet
  • Permettre de pouvoir sortir une des 3 tension (5v, 12v, 24v) par un screw terminal
    • Alimente la switch ethernet en dessous
  • MCU Connecté sur le CAN BUS
  • Sélectionner avec les GPIO les cameras qui doivent recevoir du power

Composants principaux:

  • ESP32 DEV KIT V1
  • TJA1050 (CAN BUS)
  • LTC4365 (Over/Under Voltage protaction)
  • DMG4822SSD (DIODE pour la switch du LTC4365)
  • DELs
  • CLP6C-FKB-CKNPRGJBB7A363 (ERROR DEL)
  • Boutons
  • Horizontal Amphenol 54602 RJ45
  • ASSMANN_A-2014 Ethernet connector
  • CRJ036-5-TH_2x4 Ethernet connector
  • BTS5200 (4 Channel Mosfet)

Fonctionnement:

  • Le PDB reçoit 3 tensions régulé en entrée, du 5V, du 12V et du 24V.
  • Le 12V sert principalement pour alimenter les caméras qui sont alimentés avec un POE avec un Pinout spécial. Il sert aussi à alimenter 2 circuit d'accessoires potentiels.
  • Le 24V sert à alimenter le/les antennes qui sont sur le Rover.
  • Le 5V est passé avec les fils de CanBus pour alimenter et communiquer avec les autres PCB du rover
  • Le circuit sécurise les trois tensions contre les sur-tensions et le drops de tensions.
  • La sortie vers l'ordinateur principal n'est pas utilisé, l'ordinateur est directement branché dans la switch.

PGIO

Outputs

NameGPIO
CAM_SIGN_0D18
CAM_SIGN_1D19
CAM_SIGN_2D33
CAM_SIGN_3D32
PWM_0D21
PWM_1D22
ACC1_CONTROLD23
ACC2_CONTROLD25
LED_RD14
LED_GD27
LED_BD26

Communication

NameGPIO
TXCD6
RXCD7

Parts

18
QtyValueFootprintReferences
2100kResistor_SMD:R_0805_2012MetricR2, R3
220kResistor_SMD:R_0805_2012MetricR1, R4
2BZV55B5V6Diode_SMD:D_MiniMELFD1, D3
2JST3_PinConnector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_VerticalJ4, J5
2MountingHole_PadMountingHole:MountingHole_3.2mm_M3_DIN965_Pad_TopBottomH2, H3
11KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR5
12ARoverFootprint:FUSE_3568-20F1
1JST2_PinConnector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_VerticalJ6
1JST4_PinConnector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_VerticalJ2
1JST6_PinConnector_JST:JST_PH_B6B-PH-K_1x06_P2.00mm_VerticalJ3
1LOGOLOGOG***
1RLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD2
1XT60PW-MRoverFootprint:AMASS_XT60PW-M_1x02_P7.20mm_HorizontalU1

More from robotique-udes/PCB

12
  • 4 layers152.8 × 53.5 mmDDB, the printed circuit board in 3D

    DDB

    robotique-udes/PCB

    110 partsMIT
  • 4 layers100 × 80 mmArmJ345, the printed circuit board in 3D

    ArmJ345

    robotique-udes/PCB

    98 partsMIT
  • 4 layers96.5 × 97.9 mmPdb, the printed circuit board in 3D

    Pdb

    robotique-udes/PCB

    96 partsMIT
  • 4 layers57.8 × 80 mmArm drive, the printed circuit board in 3D

    Arm drive

    robotique-udes/PCB

    69 partsMIT
  • 4 layers80 × 50 mmArm drive jl, the printed circuit board in 3D

    Arm drive jl

    robotique-udes/PCB

    62 partsMIT
  • 4 layers59.5 × 90 mmGripper 2024, the printed circuit board in 3D

    Gripper 2024

    robotique-udes/PCB

    60 partsMIT
  • 4 layers38 × 76 mmArm drive j2, the printed circuit board in 3D

    Arm drive j2

    robotique-udes/PCB

    58 partsMIT
  • 4 layers69.1 × 53 mmArmJ2, the printed circuit board in 3D

    ArmJ2

    robotique-udes/PCB

    57 partsMIT
  • 4 layers79.5 × 36 mmArmJL, the printed circuit board in 3D

    ArmJL

    robotique-udes/PCB

    57 partsMIT
  • 4 layers32.5 × 59.3 mmDrive 27A, the printed circuit board in 3D

    Drive 27A

    robotique-udes/PCB

    53 partsMIT

Similar boards

  • 4 layers86.6 × 85.1 mmDPB PCB, the printed circuit board in 3D

    DPB PCB

    V2-Tech/DPB-PCB

    118 parts1GPL-3.0
  • 2 layers36 × 47 mmMad, the printed circuit board in 3D

    Mad

    0x007E/mad

    Matrix Display

    48 parts
  • 2 layersRcl, the printed circuit board in 3D

    Rcl

    0x007E/rcl

    Color Lamp

    82 parts
  • 4 layers57.1 × 33.9 mmSabiaR1 v2, the printed circuit board in 3D

    SabiaR1 v2

    CarloCBragagnolo/SABIAR1

    Project files for the Sabiá R1 flight computer

    64 partsGPL-3.0
  • 2 layers23 × 23 mmSensorBoard, the printed circuit board in 3D

    SensorBoard

    neerajadsul/SmartSystems

    Home Monitoring with Private IoT Sensor Dashboard using Django + PostgreSQL

    14 parts
  • 2 layers25.4 × 54.6 mmSimple mesh, the printed circuit board in 3D

    Simple mesh

    ondrejh/ohMesh

    My take to Meshtastic networking.

    23 partsApache-2.0
  • 2 layers45.7 × 43.2 mmDC---DC Buck Converter-, the printed circuit board in 3D

    DC---DC Buck Converter-

    Uttu2611/DC---DC-Buck-Converter-

    DC - DC Buck Converter schematic and PCB files for drop the DC Voltage levels.

    36 parts
  • 4 layers179 × 72.5 mmEL Load Power MCU, the printed circuit board in 3D

    EL Load Power MCU

    fietser28/EL-Load

    The DCL8010 electronic load module features a DC Electronic Load with several modes and protections. This project is the for the development boards for this project. There is a seperate git project for the firmware.

    137 parts15

Questions

How big is the Selector PCB?

It measures 51 × 47.5 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Selector use?

18 parts, built around the XT60PW-M and BZV55B5V6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Selector KiCad files?

From the robotique-udes/PCB repository on GitHub, at the commit this page was made from: the board is rover/2025/Selector/latest/Selector.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Selector design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).