Skip to the content
4 layers46.4 × 32.6 mmRegulator, the printed circuit board in 3D
Size
46.4 × 32.6 mm
Copper layers
4
Thickness
1.6 mm
Parts
32
Nets
28
Pads
109
Tracks, vias
179, 79
Pours
5
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
26 Mar 2024
Updated
3 Nov 2026

Overview

Regulator is an open-source printed circuit board by robotique-udes, from the robotique-udes/PCB repository on GitHub, published under the MIT licence. It is a 4-layer board of 46.4 × 32.6 mm with 32 parts on 28 nets, routed with 179 tracks and 79 vias.

Its parts include 10 capacitors, 6 resistors, 6 connectors, 2 fuses and 1 IC. It belongs with the power boards of this library.

README

rover/2024/pdb/README.md

PDB (Power Distribution Board)

PCB servant à gérer la distribution à bas courant et le de data du rover

Image du PCB en 3D

Capture d’écran, le 2024-09-18 à 21 24 36

Objectifs:

  • Protéger tous les autres boards du Over/Under Voltage pour le 5V, 12V et 24V
    • Seulement le 5v et le 24v sont protégé, car les résistance 5% ont trop d'incertitude.
  • Injecteur POE(12V custom pinout) pour les cameras branché en Ethernet
    • On/Off possible par le MCU
  • Diriger le signal des cameras sur les bonnes pins selon la norme Ethernet
  • Agir en tant que POE pour les antennes 24V (vrai POE)
  • Controller l'alimentation de 2 circuit d'accessoires 12V
    • Par 2 connecteurs Ethernet
  • Permettre de pouvoir sortir une des 3 tension (5v, 12v, 24v) par un screw terminal
    • Alimente la switch ethernet en dessous
  • MCU Connecté sur le CAN BUS
  • Sélectionner avec les GPIO les cameras qui doivent recevoir du power

Composants principaux:

  • ESP32 DEV KIT V1
  • TJA1050 (CAN BUS)
  • LTC4365 (Over/Under Voltage protaction)
  • DMG4822SSD (DIODE pour la switch du LTC4365)
  • DELs
  • CLP6C-FKB-CKNPRGJBB7A363 (ERROR DEL)
  • Boutons
  • Horizontal Amphenol 54602 RJ45
  • ASSMANN_A-2014 Ethernet connector
  • CRJ036-5-TH_2x4 Ethernet connector
  • BTS5200 (4 Channel Mosfet)

Fonctionnement:

  • Le PDB reçoit 3 tensions régulé en entrée, du 5V, du 12V et du 24V.
  • Le 12V sert principalement pour alimenter les caméras qui sont alimentés avec un POE avec un Pinout spécial. Il sert aussi à alimenter 2 circuit d'accessoires potentiels.
  • Le 24V sert à alimenter le/les antennes qui sont sur le Rover.
  • Le 5V est passé avec les fils de CanBus pour alimenter et communiquer avec les autres PCB du rover
  • Le circuit sécurise les trois tensions contre les sur-tensions et le drops de tensions.
  • La sortie vers l'ordinateur principal n'est pas utilisé, l'ordinateur est directement branché dans la switch.

PGIO

Outputs

NameGPIO
CAM_SIGN_0D18
CAM_SIGN_1D19
CAM_SIGN_2D33
CAM_SIGN_3D32
PWM_0D21
PWM_1D22
ACC1_CONTROLD23
ACC2_CONTROLD25
LED_RD14
LED_GD27
LED_BD26

Communication

NameGPIO
TXCD6
RXCD7

Parts

32
QtyValueFootprintReferences
4Conn_01x01_PinRoverFootprint:Pad_SMD_1x3mmJ2, J3, J4, J5
35.1kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR4, R5, R6
2(TBD)Resistor_SMD:R_0805_2012MetricR1, R3
2100uFCapacitor_SMD:CP_Elec_6.3x7.7C10, C11
210uFCapacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolderC1, C6
222uFCapacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolderC5, C7
2LOGOLOGOG***, G***
2MountingHole_PadMountingHole:MountingHole_3.2mm_M3_DIN965_Pad_TopBottomH1, H2
2SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mmJP1, JP2
1(TBD)Inductor_SMD:L_SXN_SMDRI125L1
1(TBD)Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC9
1100nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC3
12.7nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC8
122.1kResistor_SMD:R_0805_2012MetricR2
13ARoverFootprint:FuseHolder-3588-20F1
15ARoverFootprint:FuseHolder-3588-20F2
1DC_DC-AP64501Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mmU1
1ETH-RJHSE5081RoverFootprint:ETH-RJHSE5081J6
1ETH-RJHSE508102RoverFootprint:ETH-RJHSE508102J1
1OPENCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC4

More from robotique-udes/PCB

12
  • 4 layers152.8 × 53.5 mmDDB, the printed circuit board in 3D

    DDB

    robotique-udes/PCB

    110 partsMIT
  • 4 layers100 × 80 mmArmJ345, the printed circuit board in 3D

    ArmJ345

    robotique-udes/PCB

    98 partsMIT
  • 4 layers96.5 × 97.9 mmPdb, the printed circuit board in 3D

    Pdb

    robotique-udes/PCB

    96 partsMIT
  • 4 layers57.8 × 80 mmArm drive, the printed circuit board in 3D

    Arm drive

    robotique-udes/PCB

    69 partsMIT
  • 4 layers80 × 50 mmArm drive jl, the printed circuit board in 3D

    Arm drive jl

    robotique-udes/PCB

    62 partsMIT
  • 4 layers59.5 × 90 mmGripper 2024, the printed circuit board in 3D

    Gripper 2024

    robotique-udes/PCB

    60 partsMIT
  • 4 layers38 × 76 mmArm drive j2, the printed circuit board in 3D

    Arm drive j2

    robotique-udes/PCB

    58 partsMIT
  • 4 layers69.1 × 53 mmArmJ2, the printed circuit board in 3D

    ArmJ2

    robotique-udes/PCB

    57 partsMIT
  • 4 layers79.5 × 36 mmArmJL, the printed circuit board in 3D

    ArmJL

    robotique-udes/PCB

    57 partsMIT
  • 4 layers32.5 × 59.3 mmDrive 27A, the printed circuit board in 3D

    Drive 27A

    robotique-udes/PCB

    53 partsMIT

Similar boards

  • 4 layers15.3 × 10.8 mmAkl ad4, the printed circuit board in 3D

    Akl ad4

    azonenberg/starshipraider

    Open hardware test equipment

    32 parts193BSD-3-Clause
  • 4 layers45.3 × 53.3 mmAntenna switch, the printed circuit board in 3D

    Antenna switch

    matthuszagh/fmcw

    6GHz frequency-modulated continuous-wave radar with real-time range detection

    32 parts66Apache-2.0
  • 4 layers34.6 × 25 mmAmiga DB23 video adapter, the printed circuit board in 3D

    Amiga DB23 video adapter

    jbilander/Amiga_DB23_video_adapter

    A PCB for creating Amiga SCART or Amiga VGA cables. You can also use this adapter to feed a new clock to the Amiga via XCLK making your machine true PAL/NTSC switchable

    32 parts42CC-BY-SA-4.0
  • 4 layers44.8 × 12.5 mmHellen1-mcz33810, the printed circuit board in 3D

    Hellen1-mcz33810

    andreika-git/hellen-one

    Hellen-One Hardware Platform for rusEFI Engine Management System

    32 parts38
  • 4 layers88.9 × 88.9 mmFlight Controller, the printed circuit board in 3D

    Flight Controller

    sondrehr/Flight_Controller

    The code used on my STM32 diy drone flight controller

    32 parts36
  • 4 layers32.9 × 100 mmFilters, the printed circuit board in 3D

    Filters

    greatscottgadgets/misc

    miscellaneous Great Scott Gadgets projects

    32 parts21GPL-2.0
  • 4 layers113.3 × 23.5 mmTinyriser6, the printed circuit board in 3D

    Tinyriser6

    a-little-wifi/Tinyriser6

    Tinyriser for the Tiny6 and Tiny7 generations of Lenovo Tiny PCs

    32 parts17CERN-OHL-S-2.0
  • 4 layers22 × 18.5 mmHc32l110, the printed circuit board in 3D

    Hc32l110

    Aightech/CleverHand-hardware

    32 parts17GPL-3.0

Questions

How big is the Regulator PCB?

It measures 46.4 × 32.6 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Regulator use?

32 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Regulator KiCad files?

From the robotique-udes/PCB repository on GitHub, at the commit this page was made from: the board is rover/2025/Regulator/latest/Regulator.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Regulator design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).