2 layers34.5 × 18.8 mm
2 layers78 × 57 mm
Signalgenerator rounded
roboter/Hardware5Repository of all my Hardware modules
- Size
- 78 × 57 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 36
- Nets
- 69
- Pads
- 233
- Tracks, vias
- 467, 7
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 31 Mar 2023
- Updated
- 18 Oct 2026
Overview
Signalgenerator rounded is an open-source printed circuit board by roboter, from the roboter/Hardware repository on GitHub. It is a 2-layer board of 78 × 57 mm with 36 parts on 69 nets, routed with 467 tracks and 7 vias.
It is built around the CH32V003F4P6, CH32V003J4M6 and AMS1117-3.3, with the SK6805E-J among its other parts. Its parts include 9 connectors, 5 resistors, 5 switches, 4 ICs and 1 diode. It belongs with the RISC-V boards of this library.
Main components
4
CH32V003F4P6
TSSOP-20-175milTSSOP-20-175mil Microcontrollers (MCU/MPU/SOC) ROHSWCH (Nanjing Qinheng Microelectronics)Microcontrollers (MCU/MPU/SOC)
CH32V003J4M6
SOP-8SOP-8 Microcontrollers (MCU/MPU/SOC) ROHSWCH (Nanjing Qinheng Microelectronics)Microcontrollers (MCU/MPU/SOC)
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
SK6805E-J
SMD,5.4x5mm-40℃~+85℃ 0.5mA 1.6mm 100mcd~200mcd 100ns 120° 1kHz 2000V 3.7V~5.5V 385mcd~697.5mcd 460nm~470nm 5.4mm 50ns 520nm~535nm 5mm 620nm~625nm 800Kbit/s 80mcd~160mcd 80ns Built-in power-on reset circuit Semi-transparent lens SMD,5.4x5mm RGB LEDs(Built-in IC) ROHSOPSCO OptoelectronicsRGB LEDs(Built-In IC)
README
WCH/KiCAD/CH32V003J4M6/CH32V003J4M6/readme.mdWCH: CH32V003J4M6 Flash: 16K SRAM: 2K Pin: 8
Parts
36| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | PC1 | TestPoint:TestPoint_Pad_D2.0mm | 1, 3, 5, 6, 7, 8 |
| 5 | 1K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5 |
| 3 | Conn_01x12 | Connector_PinSocket_2.54mm:PinSocket_1x12_P2.54mm_Vertical | J7, J8, J9 |
| 2 | Conn_01x10 | Connector_PinHeader_2.00mm:PinHeader_1x10_P2.00mm_Vertical | J1, J2 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | CH32V003F4P6 | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U1 |
| 1 | CH32V003J4M6 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | Conn_01x02 | Connector_Wago:Wago_734-132_1x02_P3.50mm_Vertical | J4 |
| 1 | Conn_01x07_Pin | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J5 |
| 1 | Conn_02x05_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J3 |
| 1 | Conn_Coaxial | Connector_Coaxial:SMA_Samtec_SMA-J-P-X-ST-EM1_EdgeMount | J6 |
| 1 | DOWN | Button_Switch_SMD:SW_Push_1P1T_NO_6x6mm_H9.5mm | SW2 |
| 1 | ENTER | Button_Switch_SMD:SW_Push_1P1T_NO_6x6mm_H9.5mm | SW5 |
| 1 | LEFT | Button_Switch_SMD:SW_Push_1P1T_NO_6x6mm_H9.5mm | SW3 |
| 1 | RIGHT | Button_Switch_SMD:SW_Push_1P1T_NO_6x6mm_H9.5mm | SW4 |
| 1 | RN42N | RF_Module:RN42N | U3 |
| 1 | SK6805 | LED_SMD:LED_SK6812_EC15_1.5x1.5mm | D1 |
| 1 | SSD1306 | SSD1306:128x64OLED | Brd1 |
| 1 | UP | Button_Switch_SMD:SW_Push_1P1T_NO_6x6mm_H9.5mm | SW1 |
| 1 | ~ | Library:LR1262 | M1 |
The 32 most common of 36 parts.
Questions
How big is the Signalgenerator rounded PCB?
It measures 78 × 57 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Signalgenerator rounded use?
36 parts, built around the CH32V003F4P6, CH32V003J4M6, AMS1117-3.3 and SK6805E-J. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Signalgenerator rounded KiCad files?
From the roboter/Hardware repository on GitHub, at the commit this page was made from: the board is WCH/KiCAD/SignalGenerator/SignalGenerator/signalgenerator-rounded.kicad_pcb and its schematic PROJECTS/LORAWAN LR1262/LR1262/LR1262.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Signalgenerator rounded design in my own project?
Its repository states no licence, so its author keeps all rights: ask roboter before reusing the design.
More from roboter/Hardware
1Similar boards
- 2 layers36.1 × 21 mm
- 2 layers50.5 × 94.7 mm
SwordOfSecretsUSBProd
gili-yankovitch/SwordOfSecrets
To solve the challenge you will need to discover a series of flags, hidden inside the sword. Each one will help you unlock the next step in the challenge, to finally reveal the ultimate secret the sword holds.
16 parts47MIT - 2 layers65.4 × 133.6 mm
BSidesTLV2025GloveBadge
bsidestlv/bsidestlv-2025-badge
To solve the challenge you will need to discover a series of flags, hidden inside the badge. Each one will help you unlock the next step in the challenge, to finally reveal the ultimate secret the badge holds.
35 parts13MIT - 2 layers14.7 × 30.6 mm
- 4 layers240 × 180 mm
- 2 layers45 × 45 mm
Just a dice
rmingon/just-a-dice
Electronic dice with CH32V003 RISC-V microcontroller. Press the PCB bottom to roll - 6 LEDs display random results. USB-powered, compact 45mm design.
27 parts - 2 layers17.8 × 33 mm
- 2 layers52.3 × 16.3 mm
