

CPU09RAM
kees 1948 Uniflex Remake
- Size
- 160 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 48
- Nets
- 127
- Pads
- 588
- Tracks, vias
- 1,764, 273
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 15 May 2025
- Updated
- 25 Feb 2026
Overview
CPU09RAM is an open-source printed circuit board by roberto314, from the roberto314/kees1948_Boards repository on GitHub. It is a 2-layer board of 160 × 100 mm with 48 parts on 127 nets, routed with 1,764 tracks and 273 vias.
It is built around the 74HC245D, MXD1210CPA+ and AS6C4008-55PCN, with the 74HC574D, 74HC138 and 74HC139D among its other parts. Its parts include 18 ICs, 15 capacitors, 2 diodes, 1 resistor and 1 connector. It belongs with the FPGA and CPLD boards of this library.
Main components
874HC245D
SO-20-300mil-40℃~+125℃ 1 160uA 2V~6V 7.8mA 7.8mA 74HC 8 9ns@4.5V,50pF Bidirectional Tri-State SOIC-20-300mil Buffers, Drivers, Receivers, Transceivers ROHSNexperiaBuffers, Drivers, Receivers, TransceiversMXD1210CPA+
PDIP-8Interface - SpecializedAnalog DevicesAS6C4008-55PCN
PDIP-320℃~+70℃ 2.7V~5.5V 30mA 4Mbit 4uA 55ns Parallel Port (Parallel) PDIP-32 SRAM ROHSAlliance MemorySRAM74HC574D
SOP-20L-40℃~+125℃ 1 13ns 15ns@6V,50pF 2.7V~6V 20uA 28MHz 5ns 6.5pF 7.8mA 7.8mA 74HC Series 8 D-Type Enable Rising Edge Tri-State SOP-20L Flip Flops ROHSMDDFlip Flops74HC138
SOP-160℃~+70℃ 24ns@5.0V,16pF 2V~6V 3/8 5.2mA 5.2mA 5uA 74HC Decoder Reverse function Single Supply SOP-16 Signal Switches, Multiplexers, Decoders ROHSGRSignal Switches, Multiplexers, Decoders74HC139D
SO-16-40℃~+125℃ 11ns@6.0V,50pF 160uA 2/4 2V~6V 74HC Decoder Single Supply SOIC-16 Signal Switches, Multiplexers, Decoders ROHSNexperiaSignal Switches / Encoders & Decoders / Multiplexers74HC21D
SOP-14-40℃~+125℃ 1.5V~4.2V 1.9V、3.98V、4.4V、5.48V、5.9V 100mV、260mV、400mV 19ns@6V,50pF 2 2V~6V 2uA 4 5.2mA 5.2mA 500mV~1.8V 74HC Series AND Gate SOIC-14 Logic Gates ROHSNexperiaGatesBAT42
DO-35-65℃~+125℃ 200mA 30V 4A 500nA@25V 650mV@50mA Independent DO-35 Schottky Diodes ROHSSTMicroelectronicsSchottky Diodes
README
README.mdkees1948_Boards
kees 1948 Uniflex Remake
This Repository is for my Remake of the PCBs from kees1948 FLEX and UniFLEX Project. I like SMD Components and started with a new Version of the CPU09RAM Board with Battery Backup.
I also started some modifications to the CPUXXCMI Board to run the Exorciser Firmware (Exbug) and in the near future i will make a Exordisk Hardware to read real floppies. See the Exorciser Subdirectory.
This is my Uniflex System:

Parts
48| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100n | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2, C3, C4, C5, C6, C7, C8, C9, C10, C11, C12, C13, C14, C15 |
| 8 | AS6C4008-55PCN | Package_SO:SOP-32_11.305x20.495mm_P1.27mm | U4, U5, U6, U7, U8, U9, U10, U11 |
| 2 | 100k | Resistor_THT:R_Array_SIP9 | RN1, RN2 |
| 2 | 74HC245 | Package_SO:SOP-20_7.5x12.8mm_P1.27mm | U15, U16 |
| 2 | 74HC574 | Package_SO:SOP-20_7.5x12.8mm_P1.27mm | U13, U14 |
| 2 | Battery_Cell | Battery:BatteryHolder_Keystone_3002_1x2032 | BT1, BT2 |
| 1 | 10u | Capacitor_Tantalum_SMD:CP_EIA-7343-31_Kemet-D_Pad2.25x2.55mm_HandSolder | C1 |
| 1 | 160x100 PCB | my_own:Eurocard_160x100_19inch_holes_connector | H1 |
| 1 | 4k7 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1 |
| 1 | 74HC138 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U18 |
| 1 | 74HC139 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U12 |
| 1 | 74HC21 | Package_SO:SO-14_3.9x8.65mm_P1.27mm | U1 |
| 1 | 74HC245 | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U3 |
| 1 | ? | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP2 |
| 1 | BAT42 | Diode_THT:D_DO-15_P10.16mm_Horizontal | D1 |
| 1 | BUS | Connector_DIN:DIN41612_C_2x32_Male_Horizontal_THT | J1 |
| 1 | Don't Touch | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP3 |
| 1 | GAL16V8 | Package_DIP:DIP-20_W7.62mm_Socket | U2 |
| 1 | MXD1210 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U17 |
| 1 | RED | LED_THT:LED_D3.0mm | D2 |
| 1 | SW_DIP_x08 | Package_DIP:DIP-16_W7.62mm_Socket | SW1 |
| 1 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm | JP1 |
| 1 | TestPoint | TestPoint:TestPoint_Keystone_5005-5009_Compact | TP1 |
| 1 | Writeprotect | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP4 |
More from roberto314/kees1948_Boards
4- 2 layers160 × 100 mm

- 2 layers206 × 132.5 mm

- 2 layers160 × 100 mm

- 2 layers160 × 100 mm

Similar boards
- 2 layers177.8 × 130.8 mm

- 2 layers208 × 110 mm

- 4 layers188 × 128.3 mm

- 2 layers180 × 67.5 mm

- 2 layers234 × 100 mm

V2b
KITTY-6502/hardware
the KITTY is a 65c02 homebrew kit microcomputer designed around text mode graphics and cartridge media. It is fully open source, and uses exclusively in-production parts.
147 parts - 2 layers233.4 × 280 mm

- 4 layers304.5 × 217.2 mm

Latest Full Backplane
Trilobyte-CPU/8-bit-computer
A DIY 8-bit computer built mostly with discrete logic chips
478 parts2 - 2 layers100 × 100 mm

RAMROM CPLD board
roberto314/Unicomp2
A modular 8-bit Computer able to recreate (nearly) every Retro computer of the late 70s to mid 80s.
46 parts1
Questions
How big is the CPU09RAM PCB?
It measures 160 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the CPU09RAM use?
48 parts, built around the 74HC245D, MXD1210CPA+, AS6C4008-55PCN and 74HC574D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the CPU09RAM KiCad files?
From the roberto314/kees1948_Boards repository on GitHub, at the commit this page was made from: the board is CPU09RAM/CPU09RAM/CPU09RAM.kicad_pcb and its schematic 09FLP/09FLP/09FLP.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the CPU09RAM design in my own project?
Its repository states no licence, so its author keeps all rights: ask roberto314 before reusing the design.