2 layers50 × 50 mm
2 layers64.8 × 36.8 mm
Lamp controller using MQTT and NodeMCU
- Size
- 64.8 × 36.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 24
- Nets
- 21
- Pads
- 102
- Tracks, vias
- 79, 4
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 20 Apr 2017
- Updated
- 23 Apr 2017
Overview
Lamps is an open-source printed circuit board by rmd6502, from the rmd6502/NodeMCULights repository on GitHub, published under the MIT licence. It is a 2-layer board of 64.8 × 36.8 mm with 24 parts on 21 nets, routed with 79 tracks and 4 vias.
It is built around the ESP-12E and LD1117S33CTR-HXY. Its parts include 10 resistors, 6 transistors, 4 connectors, 2 capacitors and 2 ICs. It belongs with the lEDs and displays boards and the ESP8266 boards of this library.
Main components
2
ESP-12E
SMD,24x16mm-20℃~+70℃ -90dBm 16dBm 170mA 2.4GHz 3V~3.6V 56mA 802.11b/g/n ESP8266 Chip On-board PCB Antenna Over-the-air (OTA) update UART、SPI、I2C SMD,24x16mm WiFi Modules ROHSAi-ThinkerWiFi Modules
LD1117S33CTR-HXY
SOT-223-20℃~+85℃ 1.3V@(800mA) 15V 2mA 3.3V 800mA Fixed Over Temperature Protection SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSHXY MOSFETVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdNodeMCULights
Lamp controller using MQTT and NodeMCU
Parts
24| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 10k | Resistors_SMD:R_0603_HandSoldering | R1, R2, R3, R4, R5, R6, R7, R8, R9, R10 |
| 6 | NMOS-PMOS-SOT23-6 | TO_SOT_Packages_SMD:SOT-23-6 | Q1, Q2, Q3, Q4, Q5, Q6 |
| 2 | Screw_Terminal_1x04 | Terminal_Blocks:TerminalBlock_Pheonix_MPT-2.54mm_4pol | J2, J3 |
| 1 | 10u | Capacitors_SMD:CP_Elec_4x5.3 | C2 |
| 1 | 1u | Capacitors_SMD:CP_Elec_4x5.3 | C1 |
| 1 | BARREL_JACK | Connect:BARREL_JACK | J1 |
| 1 | CONN_01X05 | Pin_Headers:Pin_Header_Straight_1x05_Pitch2.54mm | J4 |
| 1 | ESP-12E | ESP8266:ESP-12E | U1 |
| 1 | LD1117S33CTR | TO_SOT_Packages_SMD:SOT-223 | U2 |
Similar boards
- 2 layers95.3 × 53.3 mm
- 2 layers35 × 57.5 mm
- 2 layers36.8 × 41.3 mm
- 2 layers77 × 100 mm
- 4 layers72.4 × 95.3 mm
DingoPDM
corygrant/dingoPDM
Hardware - dingoPDM is an open source, affordable automotive PDM (Power Distribution Module). Pre-assembled and tested units are available or the design can be used to build a DIY version.
156 parts128MIT - 4 layers43.4 × 25.4 mm
R820t2 breakout
emeb/r820t2
Breakout PCB design and STM32F0 firmware for the Rafael R820T2 tuner chip
83 parts85 - 4 layers40 × 40 mm
CANBoard
corygrant/CANBoard
Hardware - CAN enabled small input / output expansion board. Switch panels, steering wheel buttons/knobs, etc.
83 parts53MIT
Questions
How big is the Lamps PCB?
It measures 64.8 × 36.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Lamps use?
24 parts, built around the ESP-12E and LD1117S33CTR-HXY. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Lamps KiCad files?
From the rmd6502/NodeMCULights repository on GitHub, at the commit this page was made from: the board is kicad/lamps.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Lamps design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).