2 layers77.8 × 112.9 mm
2 layers94.7 × 83.2 mm
Ripolab pcb
ripolab/Placas-PCB1Diseño de placas PCB
- Size
- 94.7 × 83.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 36
- Nets
- 37
- Pads
- 111
- Tracks, vias
- 327, 75
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 21 Feb 2018
- Updated
- 6 Apr 2019
Overview
Ripolab pcb is an open-source printed circuit board by ripolab, from the ripolab/Placas-PCB repository on GitHub. It is a 2-layer board of 94.7 × 83.2 mm with 36 parts on 37 nets, routed with 327 tracks and 75 vias.
It is built around the ESP-12E, SPX3819M5-L-3-3 and WS2812B. Its parts include 9 diodes, 7 resistors, 4 capacitors, 2 ICs and 1 connector. It belongs with the ESP8266 boards of this library.
Main components
3
ESP-12E
SMD,24x16mm-20℃~+70℃ -90dBm 16dBm 170mA 2.4GHz 3V~3.6V 56mA 802.11b/g/n ESP8266 Chip On-board PCB Antenna Over-the-air (OTA) update UART、SPI、I2C SMD,24x16mm WiFi Modules ROHSAi-ThinkerWiFi Modules
SPX3819M5-L-3-3
SOT-23-5-40℃~+85℃@(Ta) 1 20V 3.3V 420mV@(100mA) 500mA 5uA 70dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
WS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
README.mdPlacas-PCB
Diseño de placas PCB
Parts
36| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | WS2812B | LEDs:LED_WS2812B-PLCC4 | LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8 |
| 5 | 10K | Resistor_SMD:R_0805_2012Metric | R1, R2, R3, R4, R5 |
| 2 | 47uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.50mm_HandSolder | C1, C4 |
| 1 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.50mm_HandSolder | C2 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.50mm_HandSolder | R7 |
| 1 | 10nF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.50mm_HandSolder | C3 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | Conn_01x02 | Connector_Molex:Molex_PicoBlade_53261-0271_1x02_P1.25mm_Horizontal | J1 |
| 1 | D_Schottky_ALT | Diode_SMD:D_SOD-123 | D1 |
| 1 | ESP-12E | ESP8266:ESP-12E_SMD | U1 |
| 1 | G*** | ripolab_pcb:logo_ripolab_12x14mm | svg2mod |
| 1 | G*** | ripolab_pcb:logo_pcb_cara.pretty | svg2mod |
| 1 | GND | ripolab_pcb:TestPad | GND_1 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | ON1 |
| 1 | RX | ripolab_pcb:TestPad | RX_1 |
| 1 | SPDT | Button_Switch_SMD:SW_SPDT_PCM12 | SW1 |
| 1 | SPX3819M5-L-3-3 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_TL3342 | PROG1 |
| 1 | SW_Push RESET | Button_Switch_SMD:SW_SPST_TL3342 | RST1 |
| 1 | TEST_1P | ripolab_pcb:TestPad | RST_1 |
| 1 | TEST_VCC | ripolab_pcb:TestPad | VCC_1 |
| 1 | TX | ripolab_pcb:TestPad | TX_1 |
The 34 most common of 36 parts.
More from ripolab/Placas-PCB
4- 2 layers59.8 × 112.5 mm
- 2 layers94.7 × 83.2 mm
- 2 layers40.4 × 31 mm
Similar boards
- 2 layers25.6 × 23 mm
Breakout
skorokithakis/tiny-ESP8266-breakout
A very small and basic ESP8266 breakout board
12 parts115BSD-2-Clause - 2 layers49 × 25 mm
SlimeVR Tracker
CoreanXka/SlimeVR-Tracker
基于上述原因，诞生了这个项目，解决了上面的问题，并具有以下特点： - 超小尺寸，超高集成度，仅比开发板长1mm。 - 整合接口，仅用一个Type-C接口实现充电与程序下载。 - 集成最最最重要的电池保护芯片。 - 预留电池引脚接口和开关引脚接口，锂电池不再直连3.3V引脚，而是会先经过降压芯片降压后输出。 - 智能切换供电，在有外部USB供电的情况下会切断锂电池供电并进行充电，断开供电后自动使用锂电池供电。 -…
40 parts6GPL-3.0 - 2 layers50 × 50 mm
- 6 layers76 × 46.4 mm
Rp2350 driver
sequoia-hope/rp2350-motor-controller
An RP2350 based brushless motor controller
291 parts39 - 2 layers230.1 × 77.6 mm
- 2 layers112.5 × 41.5 mm
- 2 layers20 × 20 mm
- 2 layers57.4 × 56.9 mm
Weltkatze
KorewaKiyo/weltkatze
An RGB cat lamp capable of syncing over the local network or worldwide with a server
90 parts
Questions
How big is the Ripolab pcb PCB?
It measures 94.7 × 83.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Ripolab pcb use?
36 parts, built around the ESP-12E, SPX3819M5-L-3-3 and WS2812B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ripolab pcb KiCad files?
From the ripolab/Placas-PCB repository on GitHub, at the commit this page was made from: the board is ripolab_pcb/ripolab_pcb.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ripolab pcb design in my own project?
Its repository states no licence, so its author keeps all rights: ask ripolab before reusing the design.