Skip to the content
4 layers94.5 × 117 mmMinibox carrier, the printed circuit board in 3D

Minibox carrier

richarddzh/minibox1

This is the user's actual kicad carrier, not the separate integrated design. Open minibox-carrier.kicadpro in KiCad 10. There is no schematic: PCB DRC/net checks do not constitute ERC or schematic-parity verification.

Size
94.5 × 117 mm
Copper layers
4
Thickness
1.6 mm
Parts
20
Nets
26
Pads
118
Tracks, vias
347, 54
Pours
27
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
24 Sep 2026
Updated
4 Nov 2026

Overview

Minibox carrier is an open-source printed circuit board by richarddzh, from the richarddzh/minibox repository on GitHub. It is a 4-layer board of 94.5 × 117 mm with 20 parts on 26 nets, routed with 347 tracks and 54 vias.

It is built around the CPG151101D13, WJ500V-5.08-2P and WJ500V-5.08-03P-14-00A, with the YV13S-L7.85-B10KA(60)-0-DL01 among its other parts. Its parts include 9 connectors, 4 switches and 2 resistors. It belongs with the ESP32 boards of this library.

Main components

4

README

kicad/README.md

Minibox carrier v1.2 — 2026-10-10

This is the user's actual kicad carrier, not the separate integrated design. Open minibox-carrier.kicad_pro in KiCad 10. There is no schematic: PCB DRC/net checks do not constitute ERC or schematic-parity verification. The direct-solder revision is implemented; final review is documented in the Chinese HTML guide and revision checklist. Engineering-review files are not permission to manufacture or order.

Layout and parts

The board is 94.5 × 117 mm, R5, four copper layers, nominal 1.6 mm. Four Ø3.0 mm NPTH holes have 84.5 × 107 mm center spacing; KiCad centers are (10,8), (94.5,8), (10,115), (94.5,115) mm. Each hole has a 3.5 mm-radius/square conservative all-layer copper keepout. Ø3.0 mm is a tight M3 fit: check screw size/tolerance and the new enclosure. Bounding-rectangle area is only 1.28% smaller than the old 100 × 112 mm board.

PlacementRequired reservation
ESP32USB left, antenna right; estimated body stays inside PCB
RTCUpright, battery included in 27.5 × 12 mm reservation; 3.03 mm to ESP32 estimate
MAX98357Flat 27 × 24 mm reservation; bottom Y=72, above keycap top Y=80.5
Red boundaryY=76; upper bodies ≤74, lower operation envelopes ≥78
Joystick JS1Vertical, center (16.8,95.5); 30 mm diameter motion may overhang 3.20 mm; body/pad copper retain ≥1 mm to the left copper boundary
MicrophoneCenter (44.455,90.25), Ø19.5 mm envelope; top Y80.5; horizontal maximin clearance to all keycaps and joystick motion is approximately 3.40 mm
Four keysStandard 19.05 mm pitch both ways; lower row moves right 1.425 mm, retaining 8.10 mm left stagger and 0.20 mm to the screw square
KeycapsMaximum accepted envelope 18 × 18 mm; neighboring gap 1.05 mm
Wire entriesJ8/J9 left, J7 right; external wire/tool clearance still requires a fit check

SW1–SW4 use HanElectricity CPG151101D13 / C49234235; JS1 uses YTL YV13S-L7.85-B10Ka(60)-0-DL01 / C37323747. Their local footprints are traced to the exact linked drawings, not generic MX/joystick substitutes. The joystick has a press mechanism but it is intentionally unused; switch and mounting leads have no net; GPIO42 now controls amplifier GAIN. Reference PDFs and layout images are in hardware_references. The exact parts lack precise supplied 3D models; renders must not be mistaken for complete assembled-product models. Module envelopes and keycap size are acceptance reservations, not measured/verified models.

J11/J12 cable sockets are removed. Remaining female strips: 1×22 two, 1×14 one, 1×7 one, 1×6 one, 1×3 two, totaling seven strips/77 contacts. J3 is two separate 1×3 sockets, row spacing 7.62 mm, not a normal 2×3 socket. Three 5.08 mm screw terminals, four direct-solder switches, one direct-solder joystick, and two 0402 resistors complete the assembly. All components install from the front; THT leads solder from the back. J7 is KANGNEX WJ500V-5.08-03P-14-00A / C72334; J8/J9 are WJ500V-5.08-2P / C8465. Exact local footprints include the 0.60 mm joining lug, 10 mm body depth, 14.07 mm height, and a tolerance-aware courtyard. J8/J9 move left2.5/up3.94 mm from the prior version, with anchors (11.5,48.56)/(11.5,61.06). J8's actual body top aligns with the estimated ESP32 body bottom at Y45.97; their wire entries and electrical order are unchanged. The selected terminal holes are Ø1.50 mm, with unchanged Ø2.60 mm pads and 0.55 mm radial annular rings. No original Phoenix 3D model is reused to impersonate the selected WJ500V; current renders show its holes/outline, not an exact terminal body.

GPIO and Type-C

Keys → GPIO4/5/6/7 (active-low, internal pulls); RTC SDA/SCL →15/16; MIC_SD →21; amplifier GAIN/SD_MODE →42/47; GPIO17 is NC. I2S WS/BCLK/DIN →39/40/41; joystick VR1/VR2 wipers →1/2; LCD remains GPIO9–14. Actual front silkscreen identifies each module/terminal signal and its GPIO using digits only, for example SDA15, BCLK40, DIN41, and KEY1 4. Power pins retain 3V3/5V/GND; disconnected pins retain NC. Labels are on F.SilkS, not just the non-printing fabrication layer. See the authoritative wiring table. RTC front-view order is CLK/INT/SCL/SDA/3V3/GND; only functional net names and labels changed, retaining both original copper paths. INMP441 front-view left top-to-bottom is L/R(GND), WS39, SCK40; right is GND, 3V3, SD21. The lower-row centre reaches approximately58% of the upper-left key width: the requested approximate2/3 position would overlap the lower-right screw square with18 mm keycaps. The screw exclusion takes priority without moving the hole. The joystick's leftmost pad copper is X7.22 mm:1.22 mm from the X6 mm copper-pour boundary and2.22 mm from the board edge. The body gap is1.05 mm. Octal-memory GPIO35/36/37 are unused, as are USB19/20 and UART43/44. GPIO39–42 cannot simultaneously be used for external four-wire JTAG. Actual clone RGB firmware remains GPIO48; official v1.1 uses38, requiring physical board identification, not an automatic firmware change. The requested independent GPIO audit checked all44 J1/J2 pads against the official v1.1 J1/J3 table: no mapping errors or peripheral conflicts were found. Verify the clone's actual pinout/RGB before production. The user has tested the actual INMP441 module and confirmed no additional SD pull-down is needed; keep the carrier, firmware and BOM unchanged. This does not establish the module's internal resistor arrangement or apply to other module variants.

External Type-C VBUS/GND →J8; independent CC1/CC2 →J9 pads1/2. R1/R2 each pull their own CC to GND through 5.1 kΩ, 0402, 1%. Do not short CC1/CC2 or parallel Rd already present on a Type-C breakout. This identifies a ordinary 5 V sink, not USB-PD or a 3 A guarantee. No USB data traces are routed. Check regulator current and USB/external-5V backfeeding before connecting two sources.

Routing and manufacturing review

F.Cu signals/GND; In1 continuous GND; In2 separated power corridors/GND; B.Cu signals/GND. I2S prefers F.Cu/In1, with limited B.Cu/In2-ground-reference branches. The router checks actual filled reference copper every ≤0.1 mm outside necessary same-net antipads and requires one connected In1 region. Signal vias receive nearby GND stitching. This is not a signal-integrity test. Ground stitching was pruned from41 to23 vias after rerouting;18 redundant vias were removed, with candidate-by-candidate connectivity/refill checks. The current manifest records the final counts: retain return paths within 3 mm of every signal/power via and connections to separate ground-copper regions. Do not add periodic stitching along same-layer I2S traces merely for their length; the continuous reference plane carries their return current.

Signals/clearance 0.20/0.20 mm, 3V3 feeders0.65 mm, 5V feeders0.80 mm; ordinary vias 0.60/0.30 mm. Copper-edge0.50 mm; PTH hole spacing0.45 mm; Track-to-other-net pad clearance is 0.30 mm, or 0.50 mm at 5V pads. The upper keys retain their previous positions; rightmost keycap-to-edge gap0.60 mm. These tighter mechanical edge margins require an enclosure/cap tolerance check. silk ≥1.0 mm with0.15 mm strokes. Header holes1.0/pads1.7 mm; terminal holes1.5/pads2.6 mm; switch holes1.5/pads2.1 mm. Do not treat signal width or these power feeders as a 3 A qualification. Actual factory stackup/copper thickness, temperature rise and power bottlenecks remain review items. Domestic JLC capability rules distinguish limits from recommendations.

Actual latest DRC/mechanical metrics and hashes belong in assembly\manifest.json and drc.json; an absent report or failed gate means export is incomplete. Only a clean saved board may pass export_revision.py. The exporter checks all plated-pad/via centers on all four copper CAM layers against the saved PCB, and checks PTH/NPTH drill coordinates and diameters using the same lower-left origin. This is digital alignment, not factory registration certification. R1/R2 use verified UNI-ROYAL 0402WGF5101TCE/C25905, 5.1 kΩ ±1%; domestic catalog stock is not reserved. Full-assembly BOM now identifies all 17 physical pieces with C numbers, including the five LAIL female-strip sizes. Factory insertion/soldering approval, actual fit and final supply leave the BOM review-only, even if DRC is clean.

JLC placement-library mapping

Use assembly\positions-jlc-review.csv for the selected domestic JLC library, together with the full BOM and the unchanged Gerber ZIP. positions-all-review.csv records KiCad pad centres/footprint angles; it is not directly interchangeable with the JLC file. In the factory library, the seven female strips have a different zero angle and JS1 has a different head datum. The exporter fits numbered library pads to actual saved PCB pads, including the two separate J3 strips, and rejects mismatched parts or geometry. jlc-placement-review.json records each angle, origin and pad-fit residual. It also records the KiCad centre/angle and the factory origin/angle corrections. jlc-saved-placement.json preserves the actual factory-saved, refreshed readback for this board hash. Generated placements are checked against that snapshot at the website's coordinate precision. After changing the layout, regenerate from the new PCB: reuse library datum definitions, never copy old absolute positions. The old snapshot is then historical evidence, not approval of the new layout.

This corrects assembly instructions, not copper or holes. Gerber has no component-library rotation/model mapping; do not rotate PCB footprints or change Gerber geometry to repair a factory preview. Missing J4/J6 3D models are not missing parts. Verify the website's rotation convention and saved positions against the actual Gerber pads before approving factory DFM. The files remain engineering review inputs, not production approval.

Regenerate only these placement files without rerouting or re-exporting CAM:

powershell
& 'C:\Program Files\KiCad\10.0\bin\python.exe' .\kicad\export_jlc_positions.py

Current outputs and Git history

Current revisionPurpose
renders\assembly-layout.svgReservation layout, not exact assembled geometry
renders\minibox-carrier-front.png / back.pngGenuine saved-board renders
renders\minibox-carrier-isometric.pngGenuine saved-board perspective
renders\minibox-carrier-front-legend.png / back-legend.pngCurrent Chinese material legends and board/hole dimensions
assemblyDRC, manifest, SMT BOM/CPL, separate THT positions, pin map
fabricationFour-copper-layer Gerbers and separate PTH/NPTH drills
fabrication\minibox-gerber-review.zipPCB CAM review archive

Only fixed current paths are retained. Previous quote CSVs, dated revision directories and older archives are recoverable from Git history, not alternate submission inputs. The manifest records PCB/artifact hashes rather than a date as a version identifier. Do not embed the current commit SHA in generated files: it would describe the pre-export commit and change again when those files commit. No order, upload, purchase or payment is authorized by these files.

Reproducible commands

From C:\gitroot\minibox, after explicitly backing up the routed board:

powershell
& 'C:\Program Files\KiCad\10.0\bin\python.exe' .\kicad\generate_board.py --replace-routed
& 'C:\Program Files\KiCad\10.0\bin\python.exe' .\kicad\route_board.py
& 'C:\Program Files\KiCad\10.0\bin\python.exe' .\kicad\prune_ground_vias.py
& 'C:\Program Files\KiCad\10.0\bin\python.exe' .\kicad\export_revision.py

Generation replaces routing, so its default guard refuses to overwrite tracks. Inspect every command's result; do not continue after a failure. For PNGs, use KiCad pcb render --side top|bottom --quality basic (high is optional). Then run python .\kicad\add_render_legends.py; its dimensions are read from the saved PCB, and the legends now correctly identify four copper layers. After updating renders or documentation, run python .\kicad\package_review.py to refresh assembly\minibox-assembly-review.zip and all artifact hashes. Every PCB/part change requires the full export, not only the coordinate command. The full exporter now also renders the saved board's front/back/isometric PNGs and regenerates both Chinese dimension/legend images before packaging. render_source_board_sha256 binds that render batch to the exported PCB. After partial rerouting, the pruning command removes only redundant GND vias, refilling and checking each candidate's connectivity and actual I2S reference copper. It preserves a GND return via within3 mm of every signal/power via. Its reduction report is in assembly\ground-stitching-review.json; run the full export afterwards to renew DRC, renders, CAM, placements and hashes.

Parts

20
QtyValueFootprintReferences
4CPG151101D13Minibox:CPG151101D13SW1, SW2, SW3, SW4
4M3 NPTHMountingHole:MountingHole_3mmH1, H2, H3, H4
25.1k 1%Resistor_SMD:R_0402_1005MetricR1, R2
2WJ500V-5.08-2PMinibox:WJ500V_5.08_2PJ8, J9
1ESP32-S3 J1 - USB LEFTConnector_PinSocket_2.54mm:PinSocket_1x22_P2.54mm_VerticalJ1
1ESP32-S3 J3 - USB LEFTConnector_PinSocket_2.54mm:PinSocket_1x22_P2.54mm_VerticalJ2
1INMP441 two 1x3 socketsMinibox:INMP441_2x03_Row7.62mmJ3
1MAX98357A module socketConnector_PinSocket_2.54mm:PinSocket_1x07_P2.54mm_VerticalJ4
1PCF8563T upright moduleConnector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_VerticalJ5
1ST7796 14-pin displayConnector_PinSocket_2.54mm:PinSocket_1x14_P2.54mm_VerticalJ6
1WJ500V-5.08-03P-14-00AMinibox:WJ500V_5.08_3PJ7
1YV13S-L7.85-B10Ka(60)-0-DL01Minibox:YV13S_L7.85_B10Ka_60_0_DL01JS1

Similar boards

  • 2 layers42 × 40 mmClick counter Q3, the printed circuit board in 3D

    Click counter Q3

    dudgeon/count-fidget

    A lightweight, rechargeable two-key fidget that counts clicks, resets with a second key, and remembers its count while asleep or unpowered. Designed for a home-printed enclosure and professionally assembled electronics.

    82 parts
  • 2 layers90.2 × 91.3 mmPb v1, the printed circuit board in 3D

    Pb v1

    ossm-rs/ossm-rs-powerboard

    Power management PCB for AIM family motors, designed to pair with the Industrial ESP32-S3-RS485-CAN control board by Waveshare and run with OSSM-RS software.

    58 parts2
  • 2 layers81.6 × 39.7 mmShield, the printed circuit board in 3D

    Shield

    pcaunegre/MkrfoxWindShield

    Arduino Mkrfox1200 interface to wind sensors

    31 parts2Unlicense
  • 4 layers80 × 80 mmFocDrive, the printed circuit board in 3D

    FocDrive

    01binary/foc

    Field-Oriented Control Board

    125 parts1
  • 4 layers76 × 88 mmHoerbaer, the printed circuit board in 3D

    Hoerbaer

    drachosaurus/hoerbaer

    Hör Bär (v2)

    233 parts1
  • 4 layers210.9 × 127 mmDual panel, the printed circuit board in 3D

    Dual panel

    fchorney/krakenpad-poc

    proof of concept and research into making kraken pad

    174 parts1
  • 2 layers45.3 × 56.3 mmAbb welcome gateway v3, the printed circuit board in 3D

    Abb welcome gateway v3

    fquinto/abb-welcome-gateway

    ESP32 gateway for ABB‑Welcome / Busch‑Welcome 2‑wire intercoms. Doorbell notifications + remote door control in Home Assistant. Includes PCB design and firmware.

    69 parts1CERN-OHL-W-2.0
  • 4 layers110 × 85 mmPreview, the printed circuit board in 3D

    Preview

    Takazudo/zudo-pd

    P15 r1 is the common 27 × 40 mm STUSB4500 15 V / 3 A module for LED first, then PD15. The same PCB, population and NVM image serve both. Source: board-p15-draft.kicadpcb and ../../scripts/schgen/boardp15spec.py.

    285 parts1

Questions

How big is the Minibox carrier PCB?

It measures 94.5 × 117 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Minibox carrier use?

20 parts, built around the CPG151101D13, WJ500V-5.08-2P, WJ500V-5.08-03P-14-00A and YV13S-L7.85-B10KA(60)-0-DL01. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Minibox carrier KiCad files?

From the richarddzh/minibox repository on GitHub, at the commit this page was made from: the board is kicad/minibox-carrier.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Minibox carrier design in my own project?

Its repository states no licence, so its author keeps all rights: ask richarddzh before reusing the design.