
OM Landroid MB
rich21044/Openmower-for-Landroid-WR141E
Taking the hardware developed as part of ClemensElfleins work on Openmower and adapting it to fit a 2019 Landroid WR141E.

Taking the hardware developed as part of ClemensElfleins work on Openmower and adapting it to fit a 2019 Landroid WR141E.
OM Landroid MB is an open-source printed circuit board by rich21044, from the rich21044/Openmower-for-Landroid-WR141E repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 85.6 × 88.9 mm with 126 parts on 190 nets.
It is built around the SN74LV1T34DBV, MCP604-I/P and TSC101CILT, with the 74HC4051, 74ALVC164245DGG,11 and SIP32509DT among its other parts. Its parts include 27 resistors, 26 capacitors, 22 diodes, 15 connectors and 12 ICs. It belongs with the RP2040 and NXP (LPC, Kinetis, i.MX RT) boards of this library.
Taking the hardware developed as part of ClemensElfleins work on Openmower and adapting it to fit a 2019 Landroid WR141E.
This is my first venture into Github so it might get a bit clunky. Usual rules apply.. please try to be constructive, I'm learning as I go so if you're going to leave some negative feedback have the grace to tell me why and how I can put it right.
The Openmower project by ClemensElflein started all this for me and I've been so fed up with the performance (or lack thereof) of my Landroid WR141E that I considered selling it and then just buying his kit however, the Landroid does have cut to edge capability that the Open mower doesnt have and when all is said and done it probably works out at about the same cost.
According to the Gurus on Discord, the firmware in the Landroid is encoded, the data streams between the processors is encoded, the main processor is read locked and the JTAG interface is disabled. I dont have the knowledge, expertise or equipment to hack into the exiitng Landroid hardware so the plan is to make best use of the Openmower hardware and firmware thats already been developed and port it into the Landroid WR141E.
The main thrust of this first stage of the project is to adjust the Openmower motherboard to fit into the available space in the Landroid.
I am also discussing development and asking questions on Discord as @Slartibartfast
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R4, R12, R26, R28, R40, R42, R48, R50 |
| 9 | DNP | Diode_SMD:D_SMB | D4, D5, D6, D7, D8, D9, D10, D11, D12 |
| 7 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7, R13, R18, R41, R43, R45, R47 |
| 6 | 220uF | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C2, C3, C4, C6, C7, C8 |
| 5 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C15, C18, C19, C24, C26 |
| 4 | 22uF | Capacitor_SMD:C_1206_3216Metric | C16, C20, C21, C22 |
| 4 | Conn_01x03_Male | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J11, J12, J13, J14 |
| 4 | D_Schottky | Diode_SMD:D_SMA_Handsoldering | D2, D3, D15, D16 |
| 3 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C5, C25 |
| 3 | 4k7 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R14, R17, R49 |
| 3 | Conn_01x03_Pin | Landroid_Motor_Conn:TE_179839 | JC1, JL1, JR1 |
| 3 | Conn_01x04 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J5, J6, J19 |
| 3 | DNP | Diode_SMD:D_SMA | D18, D19, D20 |
| 3 | SolderJumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP6, JP7, JP8 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_D2.0mm | TP1, TP2, TP5 |
| 3 | xESC2 | xESC2:xESC2 | U4, U5, U6 |
| 2 | 150 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R27 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric | C13, C14 |
| 2 | 4.7uF | Capacitor_SMD:C_1206_3216Metric | C11, C12 |
| 2 | 47k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R44, R46 |
| 2 | 680uF | Capacitor_SMD:CP_Elec_10x12.5 | C9, C23 |
| 2 | 74HC4051 | Package_SO:SSOP-16_4.4x5.2mm_P0.65mm | U9, U10 |
| 2 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q3, Q5 |
| 2 | Conn_01x05_Socket | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J51, J52 |
| 2 | DNP | Diode_SMD:D_SOD-123F | D13, D14 |
| 2 | Fuse | MyModules:Fuseholder5x20_horiz_open_inline_Type-I | F2, F4 |
| 2 | I2C_OR_TTL | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm | JP10, JP11 |
| 2 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm | JP4, JP5 |
| 1 | 0.003R | Resistor_SMD:R_2512_6332Metric_Pad1.40x3.35mm_HandSolder | R51 |
| 1 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C17 |
| 1 | 4.7uH 5A | Inductor_SMD:L_Vishay_IHLP-2525 | L1 |
| 1 | 53k6 1% | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11 |
| 1 | 74ALVC164245DGG,11 | 74ALVC164245DGG:SOP50P810X120-48N | IC1 |
| 1 | Conn_01x02 | Connector_Molex:Molex_Mini-Fit_Jr_5566-02A_2x01_P4.20mm_Vertical | J3 |
| 1 | Conn_01x02 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J17 |
| 1 | Conn_01x02_Pin | Connector_JST:JST_XH_B2B-XH-AM_1x02_P2.50mm_Vertical | J1 |
| 1 | Conn_02x04_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J22 |
| 1 | Conn_02x04_Top_Bottom | Connector_Molex:Molex_Mini-Fit_Jr_5566-08A_2x04_P4.20mm_Vertical | J2 |
| 1 | Conn_02x06_Female | MyModules:WT901 | WT901 |
| 1 | DNP | Diode_SMD:D_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D17 |
| 1 | DNP | Capacitor_SMD:CP_Elec_10x12.5 | C10 |
| 1 | DNP | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
| 1 | D_Schottky | Diode_SMD:D_SOD-123F | D1 |
| 1 | Fan | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | M1 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | D23 |
| 1 | LSM6DSOTR | MyModules:LGA-14_2.5X3X0.86_ | AC1201 |
| 1 | MAX20405AFOF_VY+T | MAX2040:MAX2040 | IC3 |
| 1 | MCP604 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U2 |
| 1 | MK-11C04-G013 | lcsc:SW-SMD_MK-11C04-G013 | SW1 |
| 1 | Pico | PicoW:Raspberry_Pi_Pico_SMT_THT | U11 |
| 1 | Q_PMOS_GDS | Package_TO_SOT_SMD:TO-252-2 | Q6 |
| 1 | Raspberry_Pi_2_3 | RPi_c:RPi_40Pin_Fan_Courtyard | J21 |
| 1 | SIP32509DT | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | SN74LV1T34DBV | Package_TO_SOT_SMD:SOT-23-5 | U7 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP9 |
| 1 | TSC101CILT | TSC101CILT:SOT95P280X145-5N | IC2 |
| 1 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D25 |

rich21044/Openmower-for-Landroid-WR141E
Taking the hardware developed as part of ClemensElfleins work on Openmower and adapting it to fit a 2019 Landroid WR141E.

rich21044/Openmower-for-Landroid-WR141E
Taking the hardware developed as part of ClemensElfleins work on Openmower and adapting it to fit a 2019 Landroid WR141E.




bluepylons/USB-C-3-way-splitter
A splitter board (for making a cable splitter) for turning a 5V 3A USB power source to 3 5V 1A USB sources


piecol/CM5_MINIMA_REV2
Compact, feature-filled CM5 carrier board

CircuitGuy943/Sabre-Integrated-flight-controller
(🚧) A "Jack of all trades" custom flight controller board. With support for both power and control and the ability for custom firmware

It measures 85.6 × 88.9 mm and has 2 copper layers, 1.6 mm thick.
126 parts, built around the SN74LV1T34DBV, MCP604-I/P, TSC101CILT and 74HC4051. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the rich21044/Openmower-for-Landroid-WR141E repository on GitHub, at the commit this page was made from: the board is Hardware/OM_Landroid_MB/Landroid_Motor_Conn.pretty/OM Landroid MB.kicad_pcb and its schematic Hardware/MCF8316A/MCF8316A Module/MCF8316A Module.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).