

RFID/NFC board with ethernet+PoE with numerous I/Os.
- Size
- 70 × 40 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 139
- Nets
- 38
- Pads
- 238
- Tracks, vias
- 214, 9
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 17 Nov 2013
- Updated
- 30 Jul 2020
Overview
POE is an open-source printed circuit board by reportingsjr, from the reportingsjr/rfidBoard repository on GitHub. It is a 2-layer board of 70 × 40 mm with 139 parts on 38 nets, routed with 214 tracks and 9 vias.
It is built around the PS2811-4, BAS516 and 0813-1X1T-57-F, with the MMBTA42, PA1134NL and PMEG3050EP among its other parts. Its parts include 17 capacitors, 17 resistors, 10 diodes, 6 connectors and 3 transistors. It belongs with the radio and wireless and interfaces and adapters boards of this library.
Main components
8PS2811-4
SOIC16Low Input Current, High CRT, Quad Channel PhotocouplerCELUncategorisedBAS516
SOD-523Switching Diodeshongjiacheng0813-1X1T-57-F
插件0℃~+70℃ 1 Copper alloy Gold Non-LED Shielded 插件 Ethernet Connectors / Modular Connectors (RJ45 RJ11) ROHSBel FuseEthernet Connectors / Modular Connectors (RJ45 RJ11)MMBTA42
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mV 300V 350mW 500mA 50MHz 5V NPN SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)PA1134NL
--40℃~+125℃ 253.4uH - Pulse Transformers(LAN) ROHSPulse ElecPulse Transformers(LAN)PMEG3050EP
SOD-1281 Independent 30V 360mV@5A 5A 70A 8mA@30V SOD-128 Schottky Diodes ROHSNexperiaSchottky DiodesSMAJ58A
DO-214AC(SMA)-55℃~+150℃ 1uA 4.3A@10/1000us 400W@10/1000us 58V 71.2V 93.6V IEC 61000-4-2 TVS Unidirectional DO-214AC(SMA) ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)TLV431ASN
TSOP-5-1.5mm-40℃~+85℃@(Ta) 1.24V~16V 150nA 20mA 80uA Adjustable Parallel ±1% TSOP-5-1.5mm Voltage Reference ROHSonsemiVoltage Reference
README
README.mdGeneral
This repository has the source for a PCB that uses Power over Ethernet (PoE) to power an STM32F103 microcontroller. It has a 10mbit ethernet MAC/PHY and 3.3V (.6A, 2W) and 12V (.5A, 6W) supplies fed from a 5V (1.8A, 9W) power rail. This gives this board the capability to provide power and control for quite a few different peripherals. The first use of the circuit boards and software in this repository is to provide a lower cost and more versatile RFID based entry method for a local hackerspace, Hive13.
In this repository you will currently find two main sections: hardware, and software. The hardware section contains the KiCad files for the PoE (power over ethernet)/micro board and the rfid transceiver board (rfidBoad). The software section contains the software/firmware for the stm32f103 to support the wanted functionality (currently ethernet comms and rfid/access control). RFID/NFC board with ethernet+PoE with numerous I/Os.
Hardware
The hardware consists of two separate boards: rfidBoard and PoE. rfidBoard is simply an rfid transceiver and antenna. PoE has an STM32F103 microcontroller which is connected to a 10mbit ethernet MAC/PHY. It alsohas a power over ethernet supply that provides 5V@1.8A total. This 5 volt supply provides power for a 3.3V supply and a 12V supply. The 3.3V supply is meant for powering ICs and other electronics while the 12V supply is meant for providing power to electronic door latches (solenoids).
rfid antenna ST Micro's antenna.exe (can be found with google) was used to calculate the antenna size for an approximately 430nH antenna. A similar antenna of different shapes can be created by using the equations in the paper "Simple Accurate Expressions for Planar Spiral Inductances" (DOI 10.1109/4.792620). The parameters I used in antenna.exe are as follows: 2 turns, 8 segments, 1mm wide conductor, 0.25mm spacing between conductors, 35um conductor thickness, and 40mm by 40mm width and length.
Software
There is no software or firmware set up or written yet! It will consist of a TCP/IP stack, an RFID stack, and a user access stack.
programs needed for compilation on fedora: sudo yum install arm-none-eabi-gcc-cs arm-none-eabi-newlib scons
To program the board an STLINK v2 programmer is needed as well as stlink (on linux).
When cloning from git cd in to software/libopencm3 and run:
git submodule init
git submodule update
To flash the board with gdb and an st-link device:
In a separate terminal run the st-link server st-util -1
In another terminal run arm-none-eabi-gdb firmware.elf
Then in gdb run tar ext :4242, load, and finally either continue or run.
Datasheets
The datasheets directory contains some datasheets for different chips on board. Currently it only contains STM32 microcontroller stuff. They are large and don't fit well in to a git repository, but it helps keep everything together and makes things easier to investigate down the line.
Notes and Issues
- TODO: Add fuses on to POE board to protect circuitry.
- Several of the components in the PoE circuitry get WAY too hot.
- C5 (4.7uF cap on the PoE input) should have the negative pin connected to GNDA/Pout rather than VPortN.
The 12V power supply current rating pretty much maxes out what the PoE can theoretically supply. Probably should derate the 12V supply quite a lot. This means that the 3.3V, 5V, and 12V will interfere with each other which is bad.Updated current rating to 500mA which provides an ok margin for total power.D1 may need to be unidirectional. The part specified in the BOM is currently bidirectional.D1 should be a schottky!- D2 is actually a zener, not a schottky as currently shown.
- The footprint for U1 (LTC4267) is undersized.
Parts
139| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 1uF | IPC7351-Nominal:CAPC1608X90 | C12, C16, C17 |
| 3 | BAS516 | rfid:SOD-523 | D3, D4, D7 |
| 2 | 0.250R | IPC7351-Nominal:RESC2013X65 | R4, R400 |
| 2 | 100nF | IPC7351-Nominal:CAPC1608X90 | C10, C11 |
| 2 | 100uF, 6.3V, X5R | IPC7351-Nominal:CAPC3216X180 | C14, C15 |
| 2 | 220K | IPC7351-Nominal:RESC1608X55 | R2, R3 |
| 2 | CDNBS04-B08200 | rfid:CDNBS04 | D6, D9 |
| 1 | +5V | Measurement_Points:Measurement_Point_Round-SMD-Pad_Big | P4 |
| 1 | 0.1uF, 100V, X7R | IPC7351-Nominal:CAPC2012X95 | C1 |
| 1 | 0813-1X1T-57-F | rfid:0813-1X1T-57-F | J1 |
| 1 | 100R, 1/8W | IPC7351-Nominal:RESC2012X70 | R7 |
| 1 | 100k | IPC7351-Nominal:RESC1608X55 | R8 |
| 1 | 100k, 1% | IPC7351-Nominal:RESC1608X55 | R13 |
| 1 | 10R | IPC7351-Nominal:RESC1608X55 | R10 |
| 1 | 10k | IPC7351-Nominal:RESC1608X55 | R1 |
| 1 | 1N5237B, 8.2V | rfid:SOD-123 | D5 |
| 1 | 1k | IPC7351-Nominal:RESC1608X55 | R11 |
| 1 | 1uF, 100V | IPC7351-Nominal:CAPC3216X180 | C2 |
| 1 | 2.8k | IPC7351-Nominal:RESC1608X55 | R22 |
| 1 | 2.8nF, 250VAC, YCAP | IPC7351-Nominal:CAPC4532X150 | C8 |
| 1 | 220uF, 6.3v | rfid:EEE-FK0J221P | C9 |
| 1 | 27nF | IPC7351-Nominal:CAPC2012X88 | C7 |
| 1 | 2N7002 | smd-semi:SOT-23 | Q2 |
| 1 | 3.3uH | IPC7351-Nominal:INDC2012X130 | L1 |
| 1 | 33.2k | IPC7351-Nominal:RESC1608X55 | R14 |
| 1 | 33nF | IPC7351-Nominal:CAPC1608X95 | C13 |
| 1 | 4.7K | IPC7351-Nominal:RESC1608X55 | R5 |
| 1 | 4.7uF, 100v | rfid:EEE-2AA4R7UP | C5 |
| 1 | 4.7uF, 10V | IPC7351-Nominal:CAPC2012X135 | C4 |
| 1 | 470R | IPC7351-Nominal:RESC1608X55 | R21 |
| 1 | 470pF | IPC7351-Nominal:CAPC1608X90 | C6 |
| 1 | 47k | IPC7351-Nominal:RESC1608X55 | R12 |
| 1 | 510R | IPC7351-Nominal:RESC1608X55 | R6 |
| 1 | 5V LED | LEDs:LED-0603 | D12 |
| 1 | 5Vout | Connect:1pin | P6 |
| 1 | 6.8k | IPC7351-Nominal:RESC1608X55 | R9 |
| 1 | 68pF, 200V | IPC7351-Nominal:CAPC1608X87 | C3 |
| 1 | CONN_01X05 | conn-2mm:CONN-2MM-F-1x5 | P5 |
| 1 | GND | Measurement_Points:Measurement_Point_Round-SMD-Pad_Big | P3 |
| 1 | GNDout | Connect:1pin | P7 |
| 1 | LOGO | mech:OSHW-6mm | G*** |
| 1 | LTC4267-3 | IPC7351-Nominal:SOP63P600X175-16 | U1 |
| 1 | MMBTA42 | smd-semi:SOT-23 | Q3 |
| 1 | PA1134 | rfid:PA1134 | T1 |
| 1 | PMEG3050EP | rfid:SOD-128 | D1 |
| 1 | PS2811 | rfid:SSOP-4 | U3 |
| 1 | SI3440DV, NFET | rfid:TSOP-6 | Q1 |
| 1 | SMAJ58A | IPC7351-Nominal:DIOM5436X265 | D2 |
| 1 | TLV431 | smd-semi:SOT-23 | D8 |
The 58 most common of 139 parts.
Similar boards
- 4 layers40 × 40 mm

- 2 layers187.5 × 45 mm

Gamma spectrometer
Motokichirou/gamma-spectrometer
NaI(Tl) gamma spectrometer: STM32G474 + R1307 PMT + 4-board stack, KiCad schematics, LTspice simulations
231 parts - 4 layers68.6 × 21 mm

- 2 layers34.9 × 24.1 mm

Breakout 0813-1X1T-57-F
newAM/Breakout_0813-1X1T-57-F
PoE 10/100 Magjack 0813-1X1T-57-F Breakout
2 partsMIT - 2 layers34.9 × 24.1 mm

- 2 layers19 × 20 mm

LiIon Charger
SpaceTeam/uHoubolt_PCB_LiIon_Charger
Small sized PCB (19mm x 20mm). Used to control and monitor the charging process of a connected LiIon Battery.
35 parts1CERN-OHL-W-2.0 - 4 layers300 × 200 mm

- 4 layers61.6 × 95.8 mm

In car dashboard
andreiii04/in-car-dashboard
Custom STM32 in-car telemetry display: G-meter, GPS speed and cabin weather on a 2.8" TFT, with each drive logged to SD.
51 partsMIT
Questions
How big is the POE PCB?
It measures 70 × 40 mm and has 2 copper layers, 1.6 mm thick.
What parts does the POE use?
139 parts, built around the PS2811-4, BAS516, 0813-1X1T-57-F and MMBTA42. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the POE KiCad files?
From the reportingsjr/rfidBoard repository on GitHub, at the commit this page was made from: the board is hardware/POEstamp/POE.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the POE design in my own project?
Its repository states no licence, so its author keeps all rights: ask reportingsjr before reusing the design.