Skip to the content
2 layers118.5 × 71.5 mmAvionics, the printed circuit board in 3D

tusi avionics framework based on arduino

Size
118.5 × 71.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
36
Nets
96
Pads
137
Tracks, vias
143, 0
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
19 Nov 2024
Updated
19 Nov 2024

Overview

Avionics is an open-source printed circuit board by remontree, from the remontree/arduino-avionics-framework repository on GitHub. It is a 2-layer board of 118.5 × 71.5 mm with 36 parts on 96 nets, routed with 143 tracks and 0 vias.

It belongs with the AVR (ATmega, ATtiny) boards of this library.

README

readme.md

Arduino rocket avionics firmware platform

This project provides a framework for Arduino to quickly build and maintain Rocket Avionics and can be expanded according to the user's intentions. Users can easily add various sensors they want to use to the Avionics system, set them to perform custom missions, and help manage mission performance by flight stage throughout the entire flight process. This is significant in that it provides an expandable avionics framework based on Arduino, which is easily accessible, instead of existing expensive avionics such as Pixhawk. In addition, it provides not only software but also hardware design that includes basic sensors needed for avionics, helping to produce a low-cost avionics system in a short time.

feature

  1. Quick and convenient sensor addition and management
  2. Custom launch stages and mission control
  3. Providing communication packets for efficient telemetry transmission and reception with ground stations
  4. High reusability and maintainability
  5. Provide hardware circuit design
  6. support canard fin pid control

software architecture

packet architecture

In order to reduce unnecessary bit transmission during the communication process and ensure communication reliability and real-time, packets were designed and protocols were created. Data types are classified as follows. At this time, rocketstate, cmd, etc. must transmit and receive data accurately, so like the TCP protocol, when data is received from the receiver, it sends an ACK to the transmitter. If the ACK is not received from the transmitter, it is designed to transmit the data one more time. Like sensor telemetry, it sends an ACK to the transmitter. Data where real-time is important were excluded from this process.

uml

hardware

The hardware basically consists of GPS, IMU, barometer, SD reader, motor, and communication module. In addition, the user can replace and add sensors as needed. The initial version of the hardware used a breadboard, and the latest version had a new PCB design to increase stability. excluded from this process.

Parts

36
QtyValueFootprintReferences
19, , , , , , , , , , , , , , , +3
6~avionics:motor_vccU6, U7, U8, U9, U10, U11
6~avionics:motor_gndU12, U13, U14, U15, U16, U17
1ALTavionics:bmp280U5
1Arduino_Mega2560_R3_Shieldarduino-library:Arduino_Mega2560_R3_ShieldA1
1GPSavionics:gpsU3
1SDavionics:sdU4
1xbeeavionics:xbeeU2

Similar boards

  • 2 layers65 × 30 mmRgb to hdmi, the printed circuit board in 3D

    Rgb to hdmi

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    36 parts1kGPL-3.0
  • 2 layers55 × 70 mmArduino v1, the printed circuit board in 3D

    Arduino v1

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    36 parts915
  • 2 layers50.4 × 24.8 mmLEDboardRev3, the printed circuit board in 3D

    LEDboardRev3

    Architeuthis-Flux/Jumperless

    A jumperless breadboard

    36 parts914
  • 2 layers45.7 × 31.8 mmLEDx16 board, the printed circuit board in 3D

    LEDx16 board

    tardate/LittleArduinoProjects

    a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!

    36 parts803MIT
  • 2 layers32 × 24 mmEsp onelayer3, the printed circuit board in 3D

    Esp onelayer3

    cnlohr/colorchord

    Chromatic Sound to Light Conversion System

    36 parts712
  • 2 layers69 × 53.8 mmTUSS4470 shield, the printed circuit board in 3D

    TUSS4470 shield

    Neumi/open_echo

    Open Source echo sounder / depth sounder / SONAR for bathymetry and research. Arduino based and compatible.

    36 parts530
  • 2 layers99.1 × 53.3 mmABSIS Mega, the printed circuit board in 3D

    ABSIS Mega

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    36 parts431
  • 2 layers16.1 × 119 mmConnectorL, the printed circuit board in 3D

    ConnectorL

    thpoll83/PolyKybd

    PolyKybd

    36 parts411CERN-OHL-W-2.0

Questions

How big is the Avionics PCB?

It measures 118.5 × 71.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Avionics use?

36 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Avionics KiCad files?

From the remontree/arduino-avionics-framework repository on GitHub, at the commit this page was made from: the board is pcb/avionics.kicad_pcb and its schematic pcb/avionics.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Avionics design in my own project?

Its repository states no licence, so its author keeps all rights: ask remontree before reusing the design.